Three simple methods are described for the determination of amoxicillin (AMX) in bulk drug and dosage forms using iodate-iodide mixture reagent. These methods employed the well-known analytical reaction between iodate-iodide mixture in the presence of acid solution. The iodide oxidized by iodate to iodine in an amount equivalent to the -COOH group present in amoxicillin (AMX) and the liberated iodine determined by titrimetry and spectrophotometry. In the titrimetric method (method A), the liberated iodine was reacted with a measured excess of thiosulphate and the residual thiosulphate was determined by titration with a standard iodine solution using starch indicator, the method was applicable over 2 - 16 mg of AMX. In the second and third methods, the absorbance of the liberated iodine was measured at 370 nm (method B) and also iodine was reacted with starch and starch-iodine complex was measured at 570 nm (method C). In spectrophotometric methods (B and C), Beer’s law was obeyed over the concentration range of 5 - 50 and 5 - 60 µg mL-1 AMX with a molar absorptivity values of 5.55×103 L mol-1 cm-1 and 4.76×103 L mol-1 cm-1 for the method A and method B, respectively. The limits of detection (LOD) and quantification (LOQ) were calculated for method B and method C. The proposed methods were found to yield reliable results when applied to bulk drug and dosage forms analysis, and hence they can be applied in quality control laboratories.

Two simple, selective and sensitive spectrophotometric methods were developed and validated for the determination of valganciclovir hydrochloride (VLGH) in pure drug and tablets. The first method was based on the reduction of iron(III) to iron(II) by VLGH and subsequent formation of iron(III)-ferricyanide complex (Prussian blue) in acid medium which was measured at 730 nm (method A). In the second method (method B), permanganate was reduced by VLGH to bluish green manganate in alkaline medium and the absorbance was measured at 610 nm. The absorbance measured in each case was related to VLGH concentration. The experimental conditions were carefully studied and optimized. Beer’s law was obeyed over the concentration ranges of 2.5-20.0 and 2.0-40.0 µg mL-1 for method A and method B, respectively, with corresponding molar absorptivity values of 1.28×104 and 6.88×103 L mol-1 cm-1. The limits of detection (LOD) and quantification (LOQ) were 0.11 and 0.33 µg mL-1 (method A) and 0.21 and 0.64 µg mL-1 (method B). Within-day and between-day relative standard deviations (%RSD) at three different concentrations levels were < 2.4%, and the respective relative errors (%RE) were ≤ 3%. The proposed methods were successfully applied to the determination of VLGH in tablets, and the results confirmed that the proposed methods were equally precise and accurate as the official method.

<p>Two simple, rapid and inexpensive spectrophotometric methods are described for the determination of diethylcarbamazine citrate (DEC) in bulk drug and formulations. The methods are based on the charge–transfer (CT) complexation reaction involving DEC as the n- donor and 2,3-dichloro-5,6-dicyano-<italic>p</italic>-benzoquinone [DDQ] (method A) and 2,4-dinitro phenol [DNP] (method B) as π-acceptors in chloroform. The absorbance of CT complexes was measured at 480 nm for method A, and 420 nm for method B. Under optimum conditions, Beer’s law was obeyed over the concentration ranges 4-90 and 4-100 μg mL-1 for methods A and B, respectively.</p>

Propõem-se titulação e dois métodos espectrofotométricos para a determinação de citrato de dietilcarbamazina (DEC) a granel e em suas formulações, usando iodato de potássio e iodeto de potássio como reagente. Os métodos utilizam a reação analítica conhecida entre iodato e iodeto, na presença de ácido. Na titulometria (Método A), o fármaco foi tratado com excesso medido de tiossulfato, na presença de excesso não medido de mistura iodato-iodeto e, depois de um tempo de repouso de 10 min, o excesso de tiossulfato foi determinado por titulação de retorno com iodo até o ponto final com amido. A titulação é baseada em reação com estequiometria 1:3 entre DEC e iodo e o método é aplicável na faixa de 2.0-10.0 mg. O iodo liberado é medido espectrofotometricamente a 370 nm (método B) ou o complexo de iodo-amido medido a 570 nm (método C). Em ambos os métodos, a absorvância é considerada linearmente dependente da concentração de iodo, a qual, por sua vez, está relacionada à concentração de DEC. As curvas de calibração são lineares para concentrações de DEC de 2.5-50 e 2.5-30 mg mL- 1 para o método B e para o método C, respectivamente. A absortividade molar calculada e os valores de sensibilidade Sandel foram 6.48×103 L mol-1 cm- 1 e 0.0604 ug cm-2, respectivamente, para o método B, e os seus respectivos valores para o método C são 9.96×103 L mol-1 cm-1 e 0.0393 mg cm-2. Os estudos de exatidão e precisão intra-dia e inter-dia foram realizados de acordo com as diretrizes da ICH. Os métodos foram aplicados com sucesso na análise de formulações de DEC.

One titrimetric and two spectrophotometric methods are proposed for the determination of diethylcarbamazine citrate (DEC) in bulk drug and in formulations using potassium iodate and potassium iodide as reagent. The methods employ the well-known analytical reaction between iodate and iodide in the presence of acid. In titrimetry (method A), the drug was treated with a measured excess of thiosulfate in the presence of unmeasured excess of iodate-iodide mixture and after a standing time of 10 min, the surplus thiosulfate was determined by back titration with iodine towards starch end point. Titrimetric assay is based on a 1:3 reaction stoichiometry between DEC and iodine and the method is applicable over 2.0-10.0 mg range. The liberated iodine is measured spectrophotometrically at 370 nm (method B) or the iodine-starch complex measured at 570 nm (method C). In both methods, the absorbance is found to be linearly dependent on the concentration of iodine, which in turn is related to DEC concentration. The calibration curves are linear over 2.5-50 and 2.5-30 µg mL-1 DEC for method B and method C, respectively. The calculated molar absorptivity and Sandell sensitivity values were 6.48×103 L mol-1 cm-1 and 0.0604 µg cm-2, respectively, for method B, and their respective values for method C are 9.96×103 L mol-1 cm-1 and 0.0393 µg cm-2. The intra-day and inter-day accuracy and precision studies were carried out according to the ICH guidelines. The methods were successfully applied to the analysis of DEC formulations.

Dois métodos espectrofotométricos, simples, rápidos e de baixo custo são descritos para a determinação do albendazol (ALB) como fármaco e em comprimidos. Os métodos baseiam-se em reação de complexação de transferência de carga (TC) envolvendo ALB como n-doador e iodo como aceptor de σ (método A) em diclorometano ou ácido pícrico como π-aceptor (método B), em clorofórmio. A absorção de complexos TC foi medida em 380 nm para o método A e 415 nm para o método B. A otimização das condições experimentais é descrita. Sob condições ideais, a lei de Beer é obedecida nas concentrações entre 8,0 e 240 e 2,4 e 42 μg mL-1 para os métodos A e B, respectivamente. A absortividade molar aparente dos complexos de TC no respectivo λ max foi calculada como sendo 1,17×103 e 5,22×103 L mol-1 cm-1, respectivamente, e os valores de sensibilidade de Sandell correspondentes são 0,2273 e 0,0509 ng cm-2. Os limites de detecção (LOD) e quantificação (LOQ) calculados são (0,69 e 2,08) e (0,10 e 0,30) μg mL-1, com o método A e o método B, respectivamente. A exatidão intra-dia e inter-dia, expressa como % de erro relativo e precisão expressa como % DPR foi inferior a 3%. Os métodos foram aplicados para a determinação de ALB em comprimidos.

Two simple, rapid and inexpensive spectrophotometric methods are described for the determination of albendazole (ALB) in bulk drug and in tablets. The methods are based on charge-transfer (CT) complexation reaction involving ALB as n-donor and iodine as σ-acceptor (method A) in dichloromethane or picric acid (PA) as π-acceptor (method B) in chloroform. The absorbance of CT complexes was measured at 380 nm for method A, and 415 nm for method B. The optimization of the experimental conditions is described. Under optimum conditions, Beer's law obeyed over the concentration ranges 8.0-240 and 2.4-42 μg mL-1 for method A and method B, respectively. The apparent molar absorptivity of CT complexes at the respective λmax are calculated to be 1.17×103 and 5.22×103 L mol-1cm-1 respectively, and the corresponding Sandell sensitivity values are 0.2273 and 0.0509 ng cm-2. The limits of detection (LOD) and quantification (LOQ) are calculated to be (0.69 and 2.08), and (0.10 and 0.30) μg mL-1 with method A, and method B, respectively. The intra-day and inter-day accuracy expressed as % RE and precision expressed as % RSD were less than 3%. The methods were applied to the determination of ALB in tablets.

A UV-spectrophotometric method is described for the determination of lansoprazole (LAN). The method is based on the measurement of the absorbance of LAN solution in acetonitrile at 281 nm. The system obeyed Beer's law over the concentration range of 1.25-25.0 µg/mL. The degradation behavior of LAN was investigated under dry heat treatment, UV-degradation, acid hydrolysis, alkali hydrolysis and oxidation; and found to degrade extensively under acid hydrolysis, alkali hydrolysis and oxidation. The method was applied to the determination of LAN in capsule and the results were statistically compared with those of the reference method by applying Student's t-test and F-test.

Descrevem-se métodos, um titulométrico e dois espectrofotométricos, para a determinação de ofloxacino (OFX) na matéria-prima e em comprimidos, empregando a N-bromossuccinimida (NBS) como reagente analítico. Os métodos propostos envolvem a adição de excesso conhecido de NBS ao OFX, em meio ácido, seguida de determinação do NBS que não reagiu. Na titulometria, o NBS que não reagiu é determinado iodometricamente e na espectrofotometria, o NBS que não reagiu é determinado pela reação com quantidade fixa de índigo carmim (Método A) ou amarelo de metanila (Método B). Em todos os métodos, a quantidade de NBS que reagiu corresponde à quantidade de OFX. A titulometria permite a determinação de 1-8 mg de OFX e os cálculos se baseiam na estequiometria de reação de 1:5 (OFX:NBS). Na espectrofotometria, a Lei de Beer é obedecida nas faixas de concentração de 0,5-5,0 µg/mL, para o método A, e de 0,3-3,0 µg/mL, para o método B, respectivamente. Os métodos desenvolvidos foram aplicados para o teste de OFX em comprimidos e os resultados foram comparados estatisticamente com aqueles do método de referência. A precisão e a confiabilidade dos métodos foram, posteriormente, verificadas por meio dos testes de recuperação via método de adição de padrão.

One titrimetric and two spectrophotometric methods have been described for the determination of ofloxacin (OFX) in bulk drug and in tablets, employing N-Bromosuccinimide as an analytical reagent. The proposed methods involve the addition of a known excess of NBS to OFX in acid medium, followed by determination of unreacted NBS. In titrimetry, the unreacted NBS is determined iodometrically, and in spectrophotometry, unreacted NBS is determined by reacting with a fixed amount of either indigo carmine (Method A) or metanil yellow (Method B). In all the methods, the amount of NBS reacted corresponds to the amount of OFX. Titrimetry allows the determination of 1-8 mg of OFX and the calculations are based on a 1:5 (OFX:NBS) reaction stoichiometry. In spectrophotometry, Beer's law is obeyed in the concentration ranges 0.5-5.0 µg/mL for method A and 0.3-3.0 µg/mL for method B. The molar absorptivities are calculated to be 5.53x10(4) and 9.24x10(4) L/mol/cm for method A and method B, respectively. The methods developed were applied to the assay of OFX in tablets, and results compared statistically with those of a reference method. The accuracy and reliability of the methods were further ascertained by performing recovery tests via the standard-addition method.

Four new extraction-free spectrophotometric methods have been established for the quantitation of famotidine (FMT). The methods are based on the formation of yellow ion-pair complexes between FMT and four sulphonphthalein dyes viz., bromothymol blue (method A), bromophenol blue (method B), bromocresol purple (method C) and bromocresol green (method D) in dioxane or acetone medium. The experimental variables such as reagent concentration, solvent medium and reaction time have been carefully optimized to achieve the highest sensitivity. The proposed methods were applied successfully to the determination of famotidine in tablets with good accuracy and precision and without interferences from common excipients. The results obtained by the proposed methods were compared favorably with those of the reference method.

Hydroxyzine dihydrochloride (HDH), a piperazine H1-receptor antagonist and antihistamine, is a rapid acting anxiolytic used principally as an antiemetic. A sensitive, selective, and precise and accurate spectrophotometric method based on the formation of an ion-pair with orange II (ORG II) as ion-pair complexing agent was developed and validated for the determination of HDH in pharmaceuticals. The chloroform-extractable ion-pair complex exhibited an absorption maximum at 480 nm. Optimization of different experimental conditions is described. Beer's law is obeyed in the range of 1.5-15 μg mL-1 with an apparent molar absorptivity value of 2.07 × 10(4) L mol-1 cm-1 and Sandell's sensitivity value of 0.0216 μg cm-2. The limit of detection (LOD) and limit of quantification (LOQ) are 0.14 and 0.41 μg mL-1, respectively. A Job's plot of absorbance versus molar ratio of HDH to ORG II indicated (1:2) stoichiometric ratio. Within-and between-day relative standard deviations at three different concentration levels were < 3%. The developed method was successfully applied to commercial tablets. The results obtained were in good agreement with those obtained using the official method. No interference was encountered from coformulated substances. Recoveries were 96-109 %.

El dihidrocloruro de hidroxicina (HDH), una piperazina antagonista del receptor H1 y un antihistamínico, es un ansiolítico de acción rápida usado principalmente como anti-emético. Se desarrolló y validó un método espectrofotométrico sensible, selectivo, preciso y exacto basado en la formación de un par iónico con naranja II (ORG II) como un agente complejante para la determinación de HDH en productos farmacéuticos. El par iónico extraído en cloroformo exhibió un máximo de absorción a 480 nm. Se describió la optimización de las diferentes condiciones experimentales. La ley de Beer se obedeció en el intervalo de 1.5-15 μg mL-1 con un valor de absortividad molar aparente de 2.07 × 10(4) L mol-1 cm-1 y un valor de sensibilidad de Sandell de 0.0216 μg cm-2. El límite de detección (LD) y el límite de cuantificación (LC) son 0.14 y 0.41 μg mL-1, respectivamente. Una gráfica de Job de absorbancia versus relación molar de HDH y ORG II indicó una relación estequiométrica (1:2). Las desviaciones estándar relativas dentro y entre días, a tres diferentes niveles de concentración, fueron < 3%. El método desarrollado fue aplicado exitosamente a tabletas comerciales. Los resultados obtenidos estuvieron en buena concordancia con los obtenidos con el método oficial. No se encontró ninguna interferencia de parte de las sustancias de la formulación. Las recuperaciones fueron de 96-109 %.

One titrimetric and two spectrophotometric methods are described for the determination of famotidine (FMT) in either pure form or in its pharmaceutical formulations. The methods are based on redox reaction between FMT and KMnO4 in acid and alkaline media. In titrimetry, an acidified solution of FMT is titrated directly with permanganate. Direct spectrophotometry (method A) involves treating the alkaline solution of the drug with permanganate and measuring the bluish green product at 610 nm. In indirect spectrophotometry (method .), the drug solution is treated with a fixed concentration of permanganate in H2SO4 medium, and after a specified time, the unreacted permanganate is measured at 545 nm. The molar combining ratio in titrimetry and the optimum assay conditions are studied. Titrimetry is applicable over 1-10 mg range and the calculations are based on a 1:3 (FMT: KMnO4) molar-ratio. In spectrophotometry, Beer's law is obeyed over 0.75-7.5 and 2.5-20 μg mL-1 for method A and method ., respectively. The molar absorptivity values are calculated to be 2.79 × 10(4) and 1.62 × 10(4) L mol-1 cm-1 for method A and method B, respectively, and the corresponding Sandell sensitivity values are 0.012 and 0.021 μg cm-2. The limits of detection (LOD) and quantification (LOQ) are also reported for the spectrophotometric methods. The applicability of the developed methods was demonstrated by the determination of FMT in pure drug as well as in commercial dosage forms.

Se describen tres métodos, uno de titulación y dos espectrofotométricos, para la determinación de famotidina (FMT) en su forma pura o en sus formulaciones farmacéuticas. Los métodos están basados en la reacción redox entre FMT y KMnO4 en medios ácido y básico. En el método de titulación, una solución acidificada de FMT se titula directamente con permanganato de potasio. De los métodos espectrofotométricos, el método directo A consiste del tratamiento de la solución alcalina de la droga con KMnO4 y medición del producto verde azulado a 610 nm. En el método indirecto B, la solución de la druga se trata con una solución fija de KMnO4 en ácido sulfúrico y, después de un tiempo específico, el KMnO4 que no reaccionó se mide a 545 nm. Se estudió la proporción molar en el método de titulación, a fin de establecer las condiciones óptimas. Así, este método es aplicable en el intervalo de 1-10 mg, y los cálculos se basan en una proporción molar de FMT/KMnO4 (1:3). En los métodos espectrofotométricos A y B, la Ley de Beer se cumple en los intervalos de 0.757.5 y 2.5-20 μg mL-1, respectivamente. Los valores de absortividad molar se determinaron como 2.79 × 10(4) y 1.62 × 10(4) L mol-1 cm-1 para los métodos A y B, respectivamente, y los valores correspondientes de sensibilidad fueron 0.012 and 0.021 μg cm-2. Se describen igualmente los límites de detección (LOD) y cuantificación (LOQ) para los métodos espectrofotométricos. La aplicación de los métodos desarrollados se demostró en la determinación de FMT en su forma pura, así como en su forma de dosis comerciales.

Dois métodos espectrofotométricos simples, sensíveis, seletivos e baratos são descritos para a determinação de sinvastatina (SMT) a granel e em comprimidos, utilizando permanganato como reagente oxidimétrico. No método A, a SMT é tratada com excesso conhecido de permanganato em meio de ácido acético e o oxidante que não reage é medido a 550 nm, enquanto no método B, a reação é efetuada em meio alcalino e o manganato resultante é medido a 610 nm. No método A, a quantidade de permanganato que reage corresponde ao conteúdo de SMT e a absorbância diminui linearmente com o aumento da concentração; no método B, a absorbância aumenta com o aumento da concentração. As condições de trabalho do ensaio foram otimizadas e os métodos, validados de acordo com as normas do ICH. Sob condições ótimas, a SMT pode ser ensaiada nas faixas de concentração de 1,47- 17,67x10-5 e de 2,27-27,18 x10-6 mol/L pelo método A e B, respectivamente. As absortividades molares calculadas são 2 x 10³ e 2,5 x 10(4) L/ mol/cm, respectivamente, para os métodos A e B, com os valores correspondentes de sensibilidade de Sandell de 0,0387 e 0,0178 μg/cm². Os limites de detecção (LOQ) também foram relatados. A exatidão e a precisão do ensaio foram determinadas pelo cálculo de três concentrações intra- e inter-dia; a RSD intra-dia foi <2% e a exatidão foi melhor que 2,15% (RE). Os métodos foram aplicados com sucesso à determinação de SMT em comprimidos com alta porcentagem de recuperação, boa exatidão e precisão e sem interferência mensurável dos excipientes. A exatidão foi posteriormente determinada no placebo e na mistura sintética e, também, pelo método de spike recovery.

Two simple, sensitive, selective and inexpensive spectrophotometric methods are described for the determination of simvastatin (SMT) in bulk drug and in tablets using permanganate as the oxidimetric reagent. In method A, SMT is treated with a measured excess of permanganate in acetic acid medium and the unreacted oxidant is measured at 550 nm, whereas in method B the reaction is carried out in alkaline medium and the resulting manganate is measured at 610 nm. In method A, the amount of permanganate reacted corresponds to the SMT content and the absorbance is found to decrease linearly with the concentration; and in method B, the absorbance increases with concentration. The working conditions of assays were optimized, and the methods were validated according to the current ICH guidelines. Under optimum conditions, SMT could be assayed in the concentration ranges, 1.47 - 17.67x10-5 and 2.27 - 27.18 x10-6 mol/L by method A and method B, respectively. The calculated molar absorptivities are 3.2 x 10³ and 2.5 x 10(4) L/mol/cm for method A and method B, respectively with corresponding Sandell sensitivity values of 0.0387 and 0.0178 μg/cm². The limits of detection (LOD) and quantification (LOQ) have also been reported. Accuracy and precision for the assay were determined by calculating the intra-day and inter-day at three concentrations; the intra-day RSD was < 2% and the accuracy was better than 2.15 % (RE). The methods were applied successfully for the determination of SMT in tablet dosage form with a high percentage of recovery, good accuracy and precision, and without measurable interference by the excipients. The accuracy was further ascertained from placebo and synthetic mixture analysis and also from the spike-recovery method.

Dois métodos espectrofotométricos novos, usando o permanganato como o reagente oxidimétrico para a determinação da olanzapina (OLP) foram utilizados e validados de acordo com as diretrizes atuais do ICH. Os métodos envolveram a adição de excesso conhecido de permanganato à OLP em meio ácido ou alcalino, determinando-se o permanganato que não reagiu em 550 nm (método A), ou pela cor verde-azulada do manganato a 610 nm (método B). A diminuição da absorbância no método A ou o aumento da absorbância no método B, em função da concentração de OLP, foi medida e relacionada à concentração de OLP. Sob condições otimizadas, a lei de Beer foi obedecida, nas faixas de concentração de 2,0 a 20 e 1,0 a 10 ao μg mL-1, no método A e no método B, respectivamente. Os valores de absortividade molar foram de 1,34 x 104 e 2,54 x 104 l mol-1cm-1 para o método A e para o método B, respectivamente, e as sensibilidades respectivas de Sandell foram de 0,0233 e 0,0123 μg cm-2. Os LOD e os LOQ para o método A calculados foram 0,37 e 1,13 μg mL-1e os valores correspondentes para o método B foram 0,16 e 0,48 μg mL-1. A precisão intermediária, expressa como RSD, encontrou-se na faixa de 0,51 a 2,66%, e a exatidão, expressa como o erro relativo, variou de 0,79 a 2,24%. Os métodos propostos foram aplicados com sucesso ao ensaio de OLP em comprimidos comerciais, com porcentagens médias de recuperação de 102± 1,59% (método A) e de 101± 1,53% (método B). A exatidão e a confiabilidade dos métodos foram confirmadas executando testes de recuperação através de procedimento padrão de adição.

Two new spectrophotometric methods using permanganate as the oxidimetric reagent for the determination of olanzapine (OLP) were developed and validated as per the current ICH guidelines. The methods involved the addition of known excess of permanganate to OLP in either acid or alkaline medium followed by the determination of unreacted permanganate at 550 nm (method A) or bluish-green color of manganate at 610 nm (method B). The decrease in absorbance in method A or increase in absorbance in method B as a function of concentration of OLP was measured and related to OLP concentration. Under optimized conditions, Beer's law was obeyed over the ranges 2.0 to 20 and 1.0 to 10 μg mL-1 in method A and method B, respectively. The calculated molar absorptivity values were 1.34 x 10(4) and 2.54 x 10(4) l mol-1cm-1 for method A and method B respectively, and the respective Sandell sensitivities were 0.0233 and 0.0123 μg cm-2. The LOD and LOQ for method A were calculated to be 0.37 and 1.13 μg mL-1and the corresponding values for method B were 0.16 and 0.48 μg mL-1. Intermediate precision, expressed as RSD was in the range 0.51 to 2.66 %, and accuracy, expressed as relative error ranged from 0.79 to 2.24 %. The proposed methods were successfully applied to the assay of OLP in commercial tablets with mean percentage recoveries of 102 ±1.59 % (method A) and 101 ±1.53 % (method B). The accuracy and reliability of the methods were further confirmed by performing recovery tests via standard addition procedure.

Abstract Titrimetric and spectrophotometric assay of pantoprazole sodium (PPS) using permanganate as the oxidimetric reagent is described. In titrimetry, PPS is treated with a measured excess of permanganate in H2SO4 medium followed by the determination of unreacted oxidant by back titrating with a standard iron(II) solution. Spectrophotometry involves addition of a known excess of permanganate to PPS in H2SO4 medium followed by the measurement of absorbance of the residual permanganate at 545 nm. In both the methods, the amount of permanganate reacted corresponds to the PPS content. Experimental conditions that provide wide linear range, maximum sensitivity and selectivity, and accuracy and precisions have been optimized. In titrimetry, the calculations are based on a 1:1 (PPS : KMnO4) reaction stoichiometry and the method is applicable over 1.0-7.0 mg range. In spectrophotometry, Beer's law is obeyed over the concentration range 15.0-150.0 µg mL-1. The linear regression equation of the calibration graph is A = 0.78 + 0.005 C with a regression coefficient (r) of 0.9982 (n = 11). The apparent molar absorptivity is calculated to be 2.213 × 10³ l mol-1cm-1 and the Sandell sensitivity is 0.1954 µg cm-2. The limits of detection (LOD) and quantification (LOQ) calculated as per the ICH guidelines are 0.73 and 2.21 µg mL-1, respectively. Accuracy and precision of the assays were determined by computing the intra-day and inter-day variations at three different levels of PPS; the intra-day and inter-day RSD was < 3.09 % and the accuracy was better than 3.5 %. The methods were successfully applied to the determination of PPS in three different brands of tablets with good accuracy and precision, and without detectable interference by excipients. The accuracy was further ascertained by placebo blank and synthetic mixture analyses and also by recovery experiments via standard-addition procedure.

En este trabajo se describe la cuantificación de pantoprazol sódico (PPS) mediante una valoración redox usando permanganato como agente oxidante siguiendo la determinación potenciométrica y espectrofotométricamente. En potenciometría, se adiciona un exceso de permanganato en medio H2SO4 y el PPS es cuantificado valorando el excedente de permanganato con una solución estándar de Fe(II). La determinación espectrofotométrica se realiza agregando permanganato a una concentración que asegure un exceso conocido y se mide la absorbancia del permanganato residual a 545 nm. En ambos métodos la cantidad de permanganato que reacciona con PPS esta relacionada con el contenido de PPS. Fueron optimizadas las condiciones experimentales que proporcionan un rango lineal, selectividad y sensibilidad máxima, precisión y exactitud. En potenciometría, los cálculos se basan en una estequiométrica de reacción 1:1 (PPS: KMnO4) y el método es aplicable en un intervalo de 1.0-7.0 mg. En espectrofotometría, la ley de Beer es lineal en un intervalo de concentración de 15.0-150.0 µg mL-1. La regresión lineal para la curva de calibración es A = 0.78 + 0.005 C con un coeficiente de regresión (r) de 0.9982 (n = 11). El coeficiente de absorbitividad molar calculado fue de 2.213 × 10³ l mol-1 cm-1 y la sensibilidad de Sandell de 0.1954 µg cm-2. Los límites de detección y cuantificación calculados de acuerdo con la guía ICH son 0.73 y 2.21 µg mL-1, respectivamente. La precisión y exactitud de los ensayos fueron determinadas calculando la variación intra-día e inter-día a tres niveles de PPS; la desviación estándar relativa intra-día e inter-día fue < 3.09 % y la exactitud fue mejor que 3.5 %. Los métodos fueron exitosamente aplicados para la determinación de PPS en tres diferentes marcas de tabletas con buena exactitud y precisión y sin interferencia detectable por los excipientes. La exactitud fue asegurada realizando el análisis de un placebo blanco y una muestra sintética y también por los experimentos de recuperación vía el procedimiento de adiciones estándar.

Three simple and sensitive spectrophotometric methods are described for the determination of simvastatin (SMT) in bulk drug and in tablets using bromate-bromide as the bromination reagent in acid medium, and three dyes as subsidiary reagents. All the three methods are based on the bromination of SMT by a known excess of in situ generated bromine followed by determination of unreacted bromine by reacting with a fixed amount of methyl orange (method A), indigo carmine (method B) or meta-cresol purple (method C) and measuring the absorbance at 510, 610 or 540 nm. In all the methods, the amount of bromine reacted corresponds to the amount of SMT. The experimental conditions for the assay have been optimized. In all the methods, the absorbance is found to increase linearly with the concentration of SMT at the respective wavelengths. Beer's law is obeyed over the ranges 0.5-3.0, 2.5-15.0 and 2.5-15.0 |ig mL-1 for method A, method B and method C, respectively and the respective molar absorptivity values are 1.0 ×10 5, 2.3 ×10(4) and 2.1 ×10(4) l mol-1 cm-1. The limits of detection and quantification are reported for all the methods. The performance of the methods was validated according to the present ICH guidelines. The methods gave similar results in terms of precision and accuracy. The repeatability and intermediate precision, expressed by the RSD was better than 2%. The accuracy of the methods expressed as relative error was satisfactory. The proposed methods were applied to the analysis of tablet form of SMT and the results tallied well with the label claim. No interference was observed from the concomitant substances normally added to tablets. The results were statistically compared with those of a literature method by applying the Student's t-test and F-test. The accuracy and validity of the methods were further ascertained by performing recovery studies via spike method and standard-addition method.

Se describen tres métodos espectrofotométricos simples y sensibles para la determinación de simvastatina (STM) en el medicamento a granel y en comprimidos usando bromato-bromuro como el reactivo de bromación en medio ácido, y tres colorantes como reactivos subsidiarios. Los tres métodos se basan en la bromación de STM por un exceso conocido de bromo generado in situ, seguida por la determinación del bromo que no reacciona, mediante una reacción con una cantidad fija de naranja de metilo (método A), carmín índigo (método B) o púrpura de metacresol (método C), y midiendo la absorbancia a 510, 610 o 540 nm. En todos los métodos, la cantidad de bromo que reacciona corresponde a la cantidad de STM. Las condiciones experimentales para la determinación fueron optimizadas. En todos los métodos, se encontró que la absorbancia se incrementa linealmente con la concentración de SMT a las respectivas longitudes de onda. La ley de Beer se cumple en los intervalos de 0.5-3.0, 2.5-15.0 y 2.5-15.0 mL-1 para el método A, el método B y el método C, respectivamente, y los valores de los respectivos coeficientes de absortividad molar son 1.0 ×10 5, 2.3 ×10(4) y 2.1 ×10(4) l mol-1 cm-1. Los límites de detección y cuantificación se reportan para cada método. El desempeño de los métodos se validó de acuerdo con los procedimientos actuales ICH. Los métodos dieron resultados semejantes en términos de precisión y exactitud. La repetibilidad y la precisión intermedia, expresadas por el RSD fueron mejor que el 2%. La exactitud de los métodos, expresada como error relativo, fue satisfactoria. Los métodos propuestos fueron aplicados satisfactoriamente al análisis de STM en comprimidos y los resultados correspondieron con lo reportado en el marbete. No se observaron interferencias de las substancias concomitantes normalmente añadidas a los comprimidos. Los resultados fueron estadísticamente comparados con otros métodos publicados en la literatura aplicando la prueba t y F de Student. La exactitud y la validez de los métodos fueron adicionalmente comprobadas a través de la realización de estudios de recuperación de muestras fortificadas y el método de adiciones patrón.

Este trabalho descreve quatro métodos rápidos e sensíveispara a determinação de estavudina (STV) na matéria-prima ou em produtos formulados. Soluções aquosas de STV podem ser tituladas tratando-as com excesso de bromato-brometo em meio ácido clorídrico, seguido da determinação iodimétrica de bromo em excesso. Métodos espectrofotométricos tambémenvolvem a adição de excesso de bromato-brometo à amostra, seguida da determinação de bromo residual por adição de uma quantidade fixa de alaranjado de metila, índigo-carmim ou azul de timol, e de medidas de absorbância nos comprimentos de onda apropriados: 520, 610 ou 550 nm. Em todos os métodos, a quantidade de bromato consumida corresponde à quantidade de STV e os resultados da sua aplicação à determinação de STV em comprimidos e cápsulas são satisfatórios.

Four sensitive and rapid methods for the determination of stavudine (STV) in bulk drug and in dosage forms were developed and optimized. In titrimetry, aqueous solution of STV was treated with a known excess of bromate-bromide in HCl medium followed by estimation of unreacted bromine by iodometric back titration. Spectrophotometric methods involve the addition of a measured excess of bromate-bromide in HCl medium and subsequent estimation of the residual bromine by reacting with a fixed amount of methyl orange, indigocarmine or thymol blue followed by measurement of absorbance at 520 nm (method A), 610 nm (method B) or 550 nm (method C). In all the methods, the amount of bromate reacted corresponds to the amount of STV. Calculations in titrimetry were based on a 1:0.666 (STV:KBrO3) stoichiometry and the method was found to be applicable over 3.5-10 mg range. A linear increase in absorbance with concentration of STV was observed in the spectrophotometric methods, and the Beer's law was obeyed over the concentration ranges 0.125-1.75, 1-10 and 1-9.0 µg mL-1 STV for method A, method B and method C, respectively. The methods when applied to the determination of STV in tablets and capsules were found to give satisfactory results.