ABSTRACT Introduction: The objectives of this study are to experimentally evaluate the haemostatic effects of two organic substances, a membrane of chitosan and a collagen sponge coated with thrombin and human fibrinogen (TachoSil®), in sealing 7-0 needle stitches holes on the femoral arteries of rats as well as to evaluate local histological reactions. Methods: Twenty-four rats were included, and four holes were made in each common femoral artery. In the control group, haemostasis was achieved only by compression with gauze sponge; and in the two other groups, haemostasis was achieved with application of one of these two substances. Results: Membrane of chitosan and TachoSil® showed a power to reduce the time to achieve haemostasis compared with the control group (P=0.001), and the haemostatic effects of these two substances were comparable. There was lower blood loss in the groups where these two substances were used when compared with the control group, but no difference was found comparing the two substances. Conclusion: The use of these sealants did not promote more adhesion or local histological reactions when compared to the control group. Since chitosan is easy to find in nature, has a positive effect to promote haemostasis, and did not bring considerable local reactions, it might be used as a sealant in cardiovascular surgery.

Many researches aim to develop different biomaterials that are compatible with natural tissues. In vitro and in vivo tests are used to evaluate this potential. Our aim was to report the importance of the critical defect’s location for in vivo assays, to evaluate this approach; in vivo studies were performed, using different compositions of biomaterials in two critical size defects: tibia and parietal bone. Polycaprolactone was used as the main polymeric matrix with and without addition of hydroxyapatite. In vivo studies on the standard critical size defect in tibia and parietal bone were performed using Wistars models: 3x2 and 5x1 dimensions, respectively. The animals were sacrificed after 32 days; neobone formation was assessed with the histological data. The in vivo data demonstrated differences between the tibia and parietal bone groups: the influence of the bone on the neobone’s formation was notable. All the tibia defect samples had greater neobone volume when compared to the parietal data. Indeed, these bones have distinct embryology, influence of mechanical forces and vascularization rate that are well known; moreover, these characteristics were demonstrated to be critical for neobone formation.

Abstract Tissue engineering suggests different forms to reconstruct tissues and organs. One of the ways is through the use of polymeric biomaterials such as poly(L-lactic acid) (PLLA). PLLA is a recognized material in tissue engineering due to its characteristics as biocompatibility and bioresorbability. In this work PLLA fibrous membranes were produced by a simple technique known as rotary jet spinning. The rotary jet spinning consists of fibrous membranes production, with fibers of scale nano/micrometric, from a polymeric solution through the centrifugal force generated by the equipment. The membranes formed were subjected to preliminary in vitro assays to verify the cytotoxicity of the membranes made in contact with the cells. Direct cytotoxicity assays were performed through the MTT, AlamarBlue® and Live/Dead® tests, with fibroblastic and osteoblastic cells. The results obtained in this study showed that PLLA membranes produced by rotary jet spinning showed promising results in the 24-hours contact period of the cells with the PLLA fibrous membranes. The information presented in this preliminary study provides criteria to be taken in the future procedures that will be performed with the biomaterial produced, aiming at its improvement.

Rotary jet spinning (RJS) and electrospinning are techniques to obtain fibrous scaffolds. RJS is a simple method, which fabricates three-dimensional fibers by exploiting a high-speed rotating nozzle, creating a polymer jet which stretches until solidification, and does not require high voltage. In opposite, electrospinning technique needs the presence of an external electric field to create fiber from the polymeric jet solution. This article investigates both processes using two different biocompatible polymers: Poly(L-lactic acid) (PLLA) and Poly(ε-caprolactone) (PCL). Samples were characterized by scanning electron microscopy, thermogravimetric analysis, differential scanning calorimeter, and Fourier-transform infrared spectroscopy. Morphological observations showed the efficiency of both techniques in obtaining nanofibers. Thermal analyses of data indicate immiscible property of different blends and the total solvent evaporation. In vitro cytocompatibility test showed that RJS and electrospinning samples exhibited good cytocompatibility. Based on these results, it may be concluded that the fibers obtained with both technologies are non-cytotoxicity and with good biocompatibility, and might be suitable for applications as scaffold for cell growth.