The Laves phase reinforced CoCrMoSi alloy system has emerged as a candidate material to protect the surface of components to withstand harsh environments under wear and/or corrosion. However, previous reports have raised some concerns and restricted a wider selection of iron-based substrates to be coated, especially limiting the carbon content. This work aims to outline the Laves - Carbides phases in the microstructure and its effect on the properties of T400 alloy deposited on GGG40 ductile iron. Dilution of 26 % ensured Laves formation either as primary or secondary, due to high-silicon substrate selected. Departing from 41 % dilution, the alloy changed to a completely carbide strengthened system. Therefore, for the lowest dilution the coatings hardness is dictated by Laves phase whereas, for higher ones, carbides are the most influent phases.

Broadly speaking, the research and design of coatings are generally studied by way of single-track deposits; otherwise, the development of a coated part entails the understanding of how multi-track welding influences the microstructure and properties of the surface. This study evaluated the effect of track overlap on the microstructure and properties of the CoCrMoSi Tribaloy T400 alloy coatings produced on AISI 316L steel substrate. The characterization was performed by scanning electron microscopy, hardness and X-ray diffraction. The correlation between the degree of overlap and performance of the coatings was assessed by wear tests. The single track deposits showed hypoeutectic microstructure as a result of high Iron, Chromium and Nickel content. From the second track on, the chemical composition was displaced back to eutectic and then to hypereutectic with overlap of 25 and 50%, respectively. The microstructure dictated the hardness of the coatings (527 – 701 HV0.5) and the lower mass loss rate was measured for hypereutectic with primary Laves phase.

This work assessed Ni-based C276 alloy coatings by PTA with different degree of interaction with AISI 316L and API 5L X70 steel substrates. Track geometry, dilution and microstructure of coatings were evaluated by optical, scanning electron microscopy and X-ray diffraction. Properties were evaluated by hardness and wear tests. Microstructure exhibited austenite Ni-FCC dendrites and interdendrictic regions containing carbides. Dilution from 4,9 to 25,4% for coatings on API 5L X70 leaded to hardness ranging from 283 to 243 HV0,5. Otherwise, dilution between 22,3 and 41,5% for coatings on AISI 316L induced hardness from 267 to 225 HV0,5. Higher interaction with the substrate leaded to 19,8% increase of mass loss rate on API 5L X70 coatings. The slight difference for coatings properties deposited on different substrates indicated that the degree of interaction was the most significant factor.

Revestimentos soldados são amplamente usados para proteger componentes mecânicos entretanto a maioria das técnicas de soldagem disponíveis restringe a variedade de ligas de alta resistência que podem ser depositadas. O processo de plasma por arco transferido permite ultrapassar esta limitação ao utilizar material de adição na forma de pó, oferecendo a possibilidade de se customizar a composição dos revestimentos e em consequências as suas propriedades. A elevada resistência mecânica e inercia química das ligas de aluminetos tornam estas ligas atrativas para a proteção de componentes diversos. Entretanto a grande interação com o substrato que ocorre quando do processamento exige que para a otimização das propriedades e soldabilidade seja realizada uma a análise de cada sistema liga e substrato. Neste trabalho foram processados e caracterizados revestimentos utilizando uma liga fundida e triturada de Nb40wt%Al e analisado o efeito do Fe e do C nas características dos revestimentos. O trabalho confirmou que é possível processar revestimentos íntegros de Nb40wt%Al por PTA e que ocorre uma forte interação com o substrato, que vai determinar a microestrutura final e as propriedades do revestimento. Destaca-se que na customização de revestimentos de Nb-Al a diluição tem de ser considerada logo nos estágios iniciais do projeto do revestimento.

Hardfacing is widely applied to components yet the majority of the welding techniques available restrain the variety of hard alloys that can be deposited. Plasma Transferred Arc hardfacing offsets this drawback by using powdered feedstock offering the ability to tailor the chemical composition of the coating and as a consequence its properties. The high strength and chemical inertia of aluminide alloys makes them very suitable to protect components. However, the strong interaction with the substrate during hardfacing requires analysis of each alloy system to optimize its properties and weldability. This work analyzed coatings processed with a cast and ground Nb40wt%Al alloy and the effect of Fe and C on the coatings features. It confirmed that sound Nb aluminide coatings can be processed by plasma Transferred arc hardfacing and will have a strong interaction with the substrate, which determines the final microstructure and properties of coatings. Final remarks point out that during Nb-Al coating tailoring the interaction with the substrate has to be considered at the early stages of design process.

Os autores relatam três casos de pacientes portadores de psoríase que utilizaram inadvertidamente doses elevadas de metotrexato e apresentaram ulceração das lesões cutâneas de psoríase. Os efeitos adversos cutâneos do metotrexato são raros, algumas vezes dose-dependentes, outras idiossincrásicos ou relacionados com alteração de metabolização da droga, ou, ainda, interações medicamentosas

The authors report three cases of psoriatic patients who inadvertently increased Methotrexate doses and presented with ulceration of cutaneous psoriatic lesions. Adverse cutaneous effects of Methotrexate are rare. At times they may be dose related, while at others they are idiosyncratic, or related to drug metabolism or drug interactions.