Chitosan microspheres with a mean size of 140 ± 119 µm were produced by the spray and coagulation methods. The microspheres were chemically modified using the following routes: a) crosslinking with glutaraldehyde b) crosslinking with epychlorohydrin and c) acetylation. For investigation of their ability as adsorbents, the following standard proteins were chosen as adsorbates: bovine serum albumin - BSA (pI = 4.8 and MW = 66 kDa) and lysozyme (pI = 11 and MW = 14 kDa). The adsorption experiments were performed using a static method. The adsorption media and equilibrium concentration of adsorbates were varied in the ranges of pH 4-11 and 0.07-0.70 mg.ml-1, respectively. The maximum adsorption capacities (q m) and the constant of the Langmuir model (Ks) were shown to be dependent on charge interactions and on the kind of treatment performed on chitosan microspheres. The satisfactory fit of a kinetic model to the experimental data shows that the step that controls the adsorption kinetics is probably the initial adsorbate transport.

O comportamento higroscópico de produtos desidratados pode ser visualizado a partir da construção de curvas denominadas Isotermas de Sorção de Umidade (ISU). Esse tipo de curva relaciona a quantidade máxima de água absorvida por uma substância, com a pressão de vapor de equilíbrio ou a atividade de água, numa dada temperatura mantida constante. Com o objetivo de estudar posteriormente a reconstituição, material de embalagem e utilização de implantes feitos a partir de pericárdio bovino liofilizado, foram traçadas curvas de adsorção e dessorção de umidade em um analisador de sorção de vapor de água, HydrosorbTM 1000, nas temperaturas de 15, 25 e 35°C. Os resultados obtidos mostraram ISU tendendo ao tipo II, segundo a classificação de BET, reação típica de superfícies hidrofílicas com formação de monocamada e multicamadas. O fenômeno da histerese foi observado durante todo o intervalo da ISU. Os modelos matemáticos de Brunauer-Emmett-Teller (BET) e Guggenheim-Anderson-de Boer (GAB) ajustaram bem os dados experimentais permitindo o cálculo do valor monomolecular, importante para a estimativa do nível crítico de umidade residual que confere maior estabilidade de armazenamento ao produto.

Hygroscopic behavior of lyophilized products can be visualized starting from the construction of Moisture Sorption Isotherms (MSI). Such curves show the relationship between the maximum amount of absorbed water for a substance, with the equilibrium vapor pressure or water activity, at a given constant temperature. Aimed to study later the reconstitution and use of biological materials of lyophilized bovine pericardium, it was plot adsorption and desorption curves, at temperatures of 15, 25 and 35°C, on HydrosorbTM 1000 - water vapor sorption analyzer. The results showed MSI type II, according BET classification, typical reaction of hydrophilic surfaces with monolayer and multilayer formation. Histerese phenomenon was observed during the whole MSI interval. The mathematical models of BET and GAB fitted well the experimental data and allowed the water monolayer calculation, estimate the critical level of residual moisture that assures more stability to the product.

Microesferas de quitosana podem ser empregadas na área de biomaterias, em processos biotecnológicos e como adsorventes. Neste trabalho, foi empregada a técnica de atomização e coagulação para produção dessas microesferas, que permitiu o controle dos parâmetros de operação e por conseqüência a obtenção de microesferas de tamanho e faixas de tamanho específicos. Após a sua obtenção, as microesferas foram modificadas quimicamente com objetivo de estudar as resistências térmica, mecânica e química. Para isso foram empregadas três rotas distintas: a-) reticulação com glutaraldeído; b-) reticulação com epicloridrina e c-) acetilação. As microesferas preparadas apresentaram distribuição de tamanho da ordem de 140 µm com desvio padrão de 11,9 µm. Após as modificações químicas, as microesferas apresentaram temperatura de degradação térmica em torno de 300 ºC, aumento da estabilidade química à solução de HCl, e diminuição da resistência mecânica.

Chitosan microspheres can be used as biomaterial, in biotechnology processes and as adsorbents. This work is concerned with the production of chitosan microspheres using spraying and coagulation processes, which allows us to control the operating parameters and to produce chitosan microspheres of several ranges and sizes. The microspheres were modified chemically in order to study their thermal, mechanical and chemical resistance. The methods used were: 1) crosslinking with glutaraldehyde; 2) crosslinking with epichlorohydrin; 3) acetylation. The microspheres obtained presented mean particle size of 140 µm and standard deviation of 11.9 µm. The modified microspheres showed thermal degradation around 300 ºC, an increase of chemical stability using HCl solution and a decrease of mechanical resistance.

The influence of the calcification solution on the mineralization of chitosan membranes was analysed. Two factors were studied: pH and chemical composition (excess of calcium or phosphate ions) of solutions. Substrates (membranes) of chitosan underwent mineralization by soaking in calcification solutions for 7 days at 36.5 °C. As expected, SEM-EDS analyses demonstrated that higher pH and concentration of ions increases deposition, however, the morphology and composition of these deposits varies depending on which ion (phosphate or calcium) is in excess. Larger spherical deposits are observed when a calcium-rich solution is used instead of a phosphate-rich one. In the latter, the interconnectivity of the inorganic and organic (matrix) phases is very different, suggesting a different mechanism of deposition for each situation.

O presente trabalho trata da preparação e caracterização de membranas de quitosana porosas e densas, que possuem diversas aplicações tecnológicas. Para tanto, foram utilizadas as técnicas de microscopia (microscopia eletrônica de varredura - MEV - e microscopia de força atômica -MFA), titulação potenciométrica e espectroscopia no infravermelho (FTIR-ATR). A síntese das estruturas foi realizada através da secagem total ou parcial de uma solução acética de quitosana a 2,5% (w/w) seguida de coagulação em meio alcalino. Glutaraldeído foi utilizado para modificar quimicamente as membranas, tornando-as mais hidrofóbicas. A extensão deste processo pôde ser observada por FTIR-ATR, utilizando-se um plano fatorial onde foram variados o tempo de fixação e a concentração de glutaraldeído na solução de tratamento.

In this work, we studied the preparation and characterization of porous and non-porous chitosan membranes, which may have several technological uses. For characterization, we have used microscopy (scanning electron microscopy -SEM- and atomic force microscopy -AFM), potentiometric titration and infrared spectroscopy (FTIR-ATR). The synthesis of structures were done by total or partial casting of a 2.5% (w/w) chitosan acetic solution and further coagulation. Glutaraldehyde was also used to chemically modify chitosan, making it more hydrophobic. The extension of this process could be observed by FTIR-ATR, and by using a factorial plan which varied time of fixation and concentration of glutaraldehyde solution.

We describe a short time model for inducing experimental emphysema in rats by chronic tobacco smoke inhalation. Three groups of male Wistar rats (6 months old) were studied: controls (N = 8), rats intoxicated for 45 days (s-45, N = 7) or for 90 days (s-90, N = 8). The exposed animals were intoxicated 3 times a day (10 cigarettes per exposure period), 5 days a week. Pulmonary damage was assessed by means of functional tests and quantitative pathological examination of the airways and lung parenchyma. The s-45 and s-90 animals were similar in terms of functional residual capacity (FRC) corrected for body weight (FRC/kg) but both groups of smoking rats exhibited significantly higher FRC/kg values than the controls (s-45 = 6.33; s-90 = 6.46; controls = 3.78; P<0.05). When the two groups of smoking rats were pooled together and compared to controls, they showed decreased lung elastance (1.6 vs 2.19; P = 0.046) and increased mean linear intercept (Lm) (85.14 vs 66.44; P = 0.025). The s-90 animals presented higher inflammation and muscular hypertrophy at the level of the axial bronchus than the controls (P<0.05). When smoking groups were pooled and compared to controls, they presented significantly higher inflammation at the lateral level (P = 0.028), as well as airway secretory hyperplasia (P = 0.024) and smooth muscle hypertrophy (P = 0.005) at the axial level. Due to its simplicity, low cost and short duration, this technique may be a useful model to obtain new information about airspace remodeling due to chronic tobacco consumption