BACKGROUND: The second heart rate (HR) turn point has been extensively studied, however there are few studies determining the first HR turn point. Also, the use of mathematical and statistical models for determining changes in dynamic characteristics of physiological variables during an incremental cardiopulmonary test has been suggested. OBJECTIVES: To determine the first turn point by analysis of HR, surface electromyography (sEMG), and carbon dioxide output ( ) using two mathematical models and to compare the results to those of the visual method. METHOD: Ten sedentary middle-aged men (53.9±3.2 years old) were submitted to cardiopulmonary exercise testing on an electromagnetic cycle ergometer until exhaustion. Ventilatory variables, HR, and sEMG of the vastus lateralis were obtained in real time. Three methods were used to determine the first turn point: 1) visual analysis based on loss of parallelism between and oxygen uptake ( ); 2) the linear-linear model, based on fitting the curves to the set of data (Lin-Lin ); 3) a bi-segmental linear regression of Hinkley' s algorithm applied to HR (HMM-HR), (HMM- ), and sEMG data (HMM-RMS). RESULTS: There were no differences between workload, HR, and ventilatory variable values at the first ventilatory turn point as determined by the five studied parameters (p>0.05). The Bland-Altman plot showed an even distribution of the visual analysis method with Lin-Lin , HMM-HR, HMM-CO2, and HMM-RMS. CONCLUSION: The proposed mathematical models were effective in determining the first turn point since they detected the linear pattern change and the deflection point of , HR responses, and sEMG.

The conventional grinding methods in some cases are not very efficient because the arising of thermal damages in the pieces is very common. Optimization methods of cutting fluid application in the grinding zone are essential to prevent thermal problems from interaction of the wheel grains with the workpiece surface. The optimization can happen through the correct selection of the cut parameters and development of devices that eliminate air layer effects generated around the grinding wheel. This article will collaborate with the development of an experimentation methodology which allows evaluating, comparatively, the performance of the deflectors in the cutting region to minimize the air layer effect of the high speed of the grinding wheel. The air layers make the cutting fluid jet to dissipate in the machine. An optimized nozzle was used in order to compare the results with the conventional method (without baffles or deflectors) of cutting fluid application. The results showed the high eficciency of the deflectors or baffles in the finish results.

Energy consumption, air pollution and industrial waste have received special attention from public authorities in recent years. The environment has become one of the most important subjects in the context of modern life, for its deterioration impacts the quality of life populations. Driven by pressure from environmental agencies, politicians have drawn up ever stricter laws aimed at protecting the environment and preserving energy resources. All these factors have led industry, research centers and universities to focus their efforts on researching alternative production processes, creating technologies to minimize or avoid the production of environmentally aggressive residues. Up to a few years ago, the main objective of manufacturing plants was to produce goods aimed at satisfying technological and economic aspects. Green, or "dry" machining and Minimum Quantity Lubricant (MQL) machining have caught the attention of researchers and technicians in the area of machining as an alternative to traditional fluids. Thus, this work proposes to explore the MQL concept in the grinding operation. Although its advantages allow one to predict a growing range of applications for MQL, the variables of influence to be considered and the effects on the results of the process have so far been little studied. Grinding involves several input parameters but, to date, little attention has been focused on the form and quantity of cutting fluid applied to the process. The condition and rate of cutting fluid applied directly influences some of the process's output variables. This work, therefore, analyzes the behavior of the MQL technique under different lubrication and cooling conditions, developing an optimized fluid application methodology based on the creation of a special nozzle through which a minimum amount of oil is pulverized in a compressed air stream. The evaluation of the technical performance of MQL in grinding, using aluminum oxide and superabrasive CBN (cubic boron nitride) grinding wheels, consisted of an experimental analysis of the behavior of the tangential cutting force, G ratio, roughness and residual stress. The results presented herein allowed us to evaluate the behavior of the MQL technique in the grinding process, thus contributing toward an environmentally friendly technology.

O presente trabalho apresenta uma metodologia confiável e de execução rápida para a avaliação do desgaste abrasivo entre as cerâmicas Duceram e Vita nas resinas compostas Z-100 e Charisma. Estes materiais são amplamente utilizados nos consultórios e clínicas dentais para restaurações funcionais e estéticas dos dentes. Para avaliar o desgaste abrasivo entre os materiais, um disco dinâmico revestido com porcelana foi utilizado sobre um disco estático revestido com resina. Os resultados indicaram que a cerâmica Vita apresenta desgaste inferior a Duceram nas resinas analisadas.

This work presents a fast and trustworthy methodology for the evaluation of the abrasive wear between the ceramics Duceram and Vita and the composites resins Z-100 and Charisma. These materials are widely used in dental clinics to restoration of function and aesthetics of the teeth. To evaluate the abrasive wear between the materials, a dynamic disk covered with ceramic was used contrary to a static disk covered with resin. The results showed that Vita presents an inferior wear against Duceram in the resins tested.

Due to the high industrial competitiveness, the rigorous laws of environmental protection, the necessary reduction of costs, the mechanical industry sees itself forced to worry more and more with the refinement of your processes and products. In this context, can be mentioned the need to eliminate the roundness errors that appear after the grinding process. This work has the objective of verifying if optimized nozzles for the application of cutting fluid in the grinding process can minimize the formation of the roundness errors and the diametrical wear of grinding wheel in the machining of the steel VC 131 with 60 HRc, when compared to the conventional nozzles. These nozzles were analyzed using two types of grinding wheels and two different cutting fluids. Was verified that the nozzle of 3mm of diameter, integral oil and the CBN grinding wheel, were the best options to obtain smaller roundness errors and the lowest diametrical wears of grinding wheels.

The purpose of the present study was to evaluate the effects of aerobic physical training (APT) on heart rate variability (HRV) and cardiorespiratory responses at peak condition and ventilatory anaerobic threshold. Ten young (Y: median = 21 years) and seven middle-aged (MA = 53 years) healthy sedentary men were studied. Dynamic exercise tests were performed on a cycloergometer using a continuous ramp protocol (12 to 20 W/min) until exhaustion. A dynamic 24-h electrocardiogram was analyzed by time (TD) (standard deviation of mean R-R intervals) and frequency domain (FD) methods. The power spectral components were expressed as absolute (a) and normalized units (nu) at low (LF) and high (HF) frequencies and as the LF/HF ratio. Control (C) condition: HRV in TD (Y: 108, MA: 96 ms; P<0.05) and FD - LFa, HFa - was significantly higher in young (1030; 2589 ms²/Hz) than in middle-aged men (357; 342 ms²/Hz) only during sleep (P<0.05); post-training effects: resting bradycardia (P<0.05) in the awake condition in both groups; VO2 increased for both groups at anaerobic threshold (P<0.05), and at peak condition only in young men; HRV in TD and FD (a and nu) was not significantly changed by training in either groups. The vagal predominance during sleep is reduced with aging. The resting bradycardia induced by short-term APT in both age groups suggests that this adaptation is much more related to intrinsic alterations in sinus node than in efferent vagal-sympathetic modulation. Furthermore, the greater alterations in VO2 than in HRV may be related to short-term APT.