Abstract The present study evaluated the influence of carvacrol, terpinene-4-ol, and chlorhexidine on the physical-chemical properties of titanium surfaces, cell viability, proliferation, adhesion, and spreading of fibroblasts and osteoblasts in vitro. Titanium surfaces (Ti) were treated with Carvacrol (Cvc), Terpinen-4-ol (T4ol), Chlorhexidine (CHX), DMSO, and ultrapure water (Control group). Physical-chemical modifications were evaluated by surface wettability, the surface free energy (SFE) calculated from the contact angle values using the Owens-Wendt-Rabel-Kaeble (OWRK) equation, scanning electron microscopy (SEM) and energy dispersive spectrometry probe (EDS) system. Cells were seeded onto Ti-treated surfaces and incubated for 24 h and 72 h, then evaluated by Alamar blue assay and fluorescence microscopy. Surfaces treated with Cvc and T4ol showed the presence of Na, O, and Cl. All surfaces showed hydrophilic characteristics and SFE values between 5.5 mN/m and 3.4 mN/m. On the other hand, EDS peaks demonstrated the presence of O and Cl after CHX treatment. A reduction of cell viability and adhesion was noted on titanium surfaces treated with CHX after 24 and 72h. In conclusion, the results indicate that the decontamination with Cvc and T4ol on Ti surfaces does not alter the surface proprieties and allows an adequate interaction with cells involved in the re-osseointegration process such as fibroblasts and osteoblasts.

Resumo O presente estudo avaliou a influência do carvacrol, terpineno-4-ol e clorexidina nas propriedades físico-químicas de superfícies de titânio, viabilidade celular, proliferação, adesão e esplhamento de fibroblastos e osteoblastos in vitro. Superfícies de titânio (Ti) foram tratadas com Carvacrol (Cvc), Terpinen-4-ol (T4ol), Clorexidina (CHX), DMSO e água ultrapura (Grupo Controle). As modificações físico-químicas foram avaliadas pela molhabilidade da superfície, a energia livre de superfície (ELS) calculada a partir dos valores do ângulo de contato usando a equação de Owens-Wendt-Rabel-Kaeble (OWRK), microscopia eletrônica de varredura (MEV) e espectroscopia de raios X por energia dispersiva (EDS). As células foram semeadas em superfícies tratadas com Ti e incubadas por 24 h e 72 h, e avaliadas pelo ensaio Alamar blue e microscopia de fluorescência. As superfícies tratadas com Cvc e T4ol mostraram a presença de Na, O e Cl. Todas as superfícies apresentaram características hidrofílicas e valores de ELS entre 5,5 mN/m e 3,4 mN/m. Por outro lado, os picos de EDS demonstraram a presença de O e Cl após o tratamento com CHX. Uma redução da viabilidade celular e adesão foi observada em superfícies de titânio tratadas com CHX após 24 e 72h. Em conclusão, os resultados indicam que a descontaminação com Cvc e T4ol em superfícies de Ti não altera as propriedades da superfície e permite uma interação adequada com células envolvidas no processo de reosseointegração como fibroblastos e osteoblastos.

Abstract This study evaluated the influence of a fluoride-modified titanium surface on osseointegration in rats with induced diabetes. One hundred and eighty rats were randomly allocated into 3 groups with 60 animals each: Control group (C): Animals without diabetes; Diabetes Group (D): Animals with uncontrolled induced diabetes; Controlled Diabetes Group (CD): Animals with diabetes induced controlled by the insulin administration. Diabetes was induced by streptozotocin injection. Each animal received 2 implants in the proximal tibial metaphysis, one with the machined surface (M) and the other one with a fluoride-modified titanium surface (F), after 4 weeks of induction of diabetes. The animals were submitted to euthanasia 2, 4, and 6 weeks after the implant placement (n = 20 animals/group). The osseointegration was evaluated by the implant removal torque test and the histometric analysis of the non-decalcified histological sections: 1) Contact bone/implant (%BIC); 2) Bone tissue area between implant threads (%BBT). Implants with F surface showed a higher removal torque than implants with surface M in all groups. There was no difference in %BIC between the groups regardless of the surface used. The F surface showed a tendency to present higher %BBT values for the 3 evaluation periods in the D group. The fluoride-modified implant surface has no impact on the %BIC and %BBT. However, the fluoride-modified implant surface increases the locking of the implants with the bone. The hyperglycemia was associated with lower removal torque values despite the surfaces of the implant used.

Resumo Este estudo avaliou a influência de uma superfície de titânio modificada com flúor na osseointegração em ratos com diabetes induzida. Cento e oitenta ratos foram distribuídos aleatoriamente em 3 grupos com 60 animais cada: Grupo controle (C): Animais sem diabetes; Grupo Diabetes (D): Animais com diabetes induzida descompensada; Grupo Diabetes Controlado (CD): Animais com diabetes induzido controlado pela administração de insulina. O diabetes foi induzido por injeção de estreptozotocina. Cada animal recebeu 2 implantes na metáfise proximal da tíbia, um com superfície usinada (M) e outro com superfície de titânio modificado com flúor (F), após 4 semanas de indução do diabetes. Os animais foram submetidos à eutanásia 2, 4 e 6 semanas após a colocação do implante (n = 20 animais/grupo). A osseointegração foi avaliada pelo teste de torque de remoção do implante e pela análise histométrica dos cortes histológicos não descalcificados: 1) Contato osso-implante (%BIC); 2) Área de tecido ósseo entre as roscas do implante (%BBT). Os implantes com superfície F apresentaram maior torque de remoção do que os implantes com superfície M em todos os grupos. Não houve diferença no %BIC entre os grupos independente da superfície utilizada. A superfície F mostrou tendência a apresentar maiores valores de %BBT para os 3 períodos de avaliação no grupo D. As superfícies de implantes modificadas com flúor não influenciaram nos dados de %BIC e %BBT. Entretanto, essas superfícies aumentaram o travamento dos implantes no tecido ósseo. A hiperglicemia foi associada a menores torques de remoção dos implantes independentemente do tipo de superfície de implante utilizada.

Abstract This study aimed to evaluate the effect of nicotine administration on the osseointegration of a superhydrophilic implants surface on rat tibiae. Thirty-two rats were used and divided into 2 groups according to the administration or not of nicotine: HH - Installation of implants with superhydrophilic surfaces in healthy animals; and HN - Installation of implants with superhydrophilic surfaces in animals subjected to nicotine administration. The animals were euthanized 15 and 45 days after implant placement (n = 8). Osseointegration was assessed by means of biomechanical analyses (removal torque), microcomputed tomography (volume of bone around the implants- %BV/TV), and histomorphometry (bone-implant contact -%BIC and the bone area between implant threads -%BBT). The animals subject to the nicotine administration presented lower removal torque than the control animals at the 45-day period (21.88 ± 2.80 Ncm vs. 17.88 ± 2.10 Ncm). The implants placed in the control rats presented higher %BIC (54.26 ± 6.59% vs. 39.25 ± 4.46%) and %BBT (50.57 ± 5.28% vs. 32.25 ± 5.24%) than the implants placed in nicotine animals at 15-day period. The nicotine administration reduces the osseointegration at 15 days, however, the superhydrophilic surface equalized the osseointegration in nicotine-exposed animals compared with healthy animals after 45 days of implant placement.

Resumo O objetivo deste estudo foi avaliar o efeito da administração de nicotina na osseointegração de implantes com superfície modificada por jateamento de oxidos e ataque ácido instalados em tíbia de ratos. Foram utilizados 32 ratos que foram divididos em 2 grupos de acordo com a administração ou não de nicotina: HH - Instalação de implantes com superfícies superhidrofílicas em animais sadios; e HN - Instalação de implantes com superfícies superhidrofílicas em animais submetidos à administração de nicotina. Os animais foram eutanasiados 15 e 45 dias após a colocação do implante (n = 8). A osseointegração foi avaliada por meio de análises biomecânicas (torque de remoção), microtomografia (volume de osso ao redor dos implantes - %BV/TV) e histomorfometrica (contato osso-implante -%BIC e área óssea entre roscas do implante -%BBT). Os animais submetidos à administração de nicotina apresentaram menor torque de remoção do que os animais controle no período de 45 dias (21,88 ± 2,80 Ncm vs. 17,88 ± 2,10 Ncm). Os implantes colocados nos ratos controle apresentaram maiores %BIC (54,26 ± 6,59% vs. 39,25 ± 4,46%) e %BBT (50,57 ± 5,28% vs. 32,25 ± 5,24%) do que os implantes colocados nos animais submetidos a administração de nicotina no período de 15 dias. A administração de nicotina prejudicou a osseointegração no período de 15 dias. Entretanto, a superfície superhidrofílica equalizou a osseointegração em animais expostos à nicotina em comparação com animais saudáveis após 45 dias da colocação do implante.

Aim Evaluation of ridge alteration after 1 year follow up after immediate loading implant placement. Methods Ten patients were included in the study, in whom the ridge volume, height, and thickness were evaluated from region of interest (ROI) of tomographic images of the operated areas (test group) and compared to the opposite tooth (control group). Results After one year, there was no implant loss and all patients were satisfied with the treatment. In the test group there was a statistically significant increase in ridge height (2.89±1.05 mm) when compared to the control group. No significant difference in relation to ridge volume and thickness was observed. In the intragroup evaluation, a significant gain in ridge height (2.65±3.08 mm) was observed when compared to baseline. Conclusion The placement of an immediate implant, temporary crown, and tissue regeneration in sockets with buccal defects promotes the regeneration of the buccal wall while preventing the reduction of bone volume and thickness.

Resumo O objetivo deste foi o de avaliar o efeito de uma superfície modificada por jateamento e ataque ácido e mantida em solução isotônica em comparação a uma superfície lisa sobre a osseointegração de implantes em animais hiperglicêmicos. No estudo foram utilizados 64 ratos, que foram divididos em 4 grupos com 16 animais em cada, e que foram avaliados em dois períodos experimentais (15 e 45 dias), com 8 animais em cada grupo. Os grupos foram divididos de acordo com o tipo de implante que foi instalado na tíbia dos animais e a condição sistêmica dos mesmos: Grupo CM - Implantes maquinados instalados em animais saudáveis; Grupo CH - Implantes maquinados instalados em animais com hiperglicemia; Grupo HM - Implantes hidrofílicos instalados em animais saudáveis, Grupo HH- Implantes hidrofílicos instalados em animais com hiperglicemia. Foram realizadas análises: biomecânicas (contra torque de remoção dos implantes), histométricas (avaliação do contato do osso com os implantes e da área de formação óssea entre as roscas) e microtomográfica (avaliação da área óssea ao redor dos implantes). Foi verificado que os implantes com superfície hidrofílica apresentaram maiores torques de remoção, quantidade de osso ao redor dos implantes e maiores valores de %BIC e %BBT em animais normo e hiperglicêmicos. Conclui-se que a superfície hidrofílica acelera o processo de osseointegração (~15% de %BIC/%BBT aos 15 dias), especialmente em animais com hiperglicêmicos. A superfície hidrofílica igualou a osseointegração entre animais normo- e hiperglicêmicos, revertendo o potencial negativo da hiperglicemia no processo de osseointegração.

Abstract The purpose of this study was to evaluate the effect of a surface modified by blasting and acid attack and maintained in an isotonic solution compared to a machined surface on osseointegration in normo- and hyperglycaemic animals. Sixty-four animals were allocated into 4 groups with 16 animals each, and they were subdivided into two experimental periods (15 and 45 days), with 8 animals in each group. The groups were divided according to the type of implant that was installed in the animals' tibia and the animals’ systemic condition: CM - Machined implants placed in Healthy animals; CH - Hydrophilic implants placed in Healthy animals, HM - Machined implants placed in animals with hyperglycaemia; HH- Hydrophilic implants installed in animals with hyperglycaemia. The following analyses were performed: biomechanical (removal torque), microtomographic (evaluation of the bone volume around the implants- BV/TV), and histomorphometric (evaluation of bone-implant contact BIC% and of the bone formation area between the threads BBT%). It was found that the implants with hydrophilic surfaces presented higher removal torques and quantities of BV/TV% and higher BIC% and BBT% values in normo- and hyperglycaemic animals. The results of this study indicated that the hydrophilic surface accelerates the osseointegration process (~ 15% BIC/BBT at 15-day period), especially in animals with hyperglycaemia. The hydrophilic surface equaled the osseointegration between normo- and hyperglycaemic animals, reversing the negative potential of hyperglycaemia on the osseointegration process.

Abstract Objective This study aimed to retrospectively collect clinical data to evaluate the influence of possible risk factors on the long-term success of implant treatment with extra-narrow (2.9 mm diameter) implants in a daily dental practice setting. Methodology Data were collected from records of patients who received at least one extra-narrow implant from 2012 to 2017, regarding implant survival, prosthesis survival, patient characteristics, and implant characteristics. The association between the dependent variables “implant survival”, “prosthesis survival,” and “adverse events” related to patient and implant characteristics was statistically evaluated by chi-square tests. Moreover, implant and prosthesis survival were analyzed by Kaplan-Meier survival curves. Results The sample was constituted of 58 patients (37 women and 21 men) with a mean age of 54.8 years old (SD: 12.5), followed up for up to eight years. In total, 86 extra-narrow implants were placed within this sample. Four implants were lost, resulting in an implant survival rate of 95.3%. A total of 55 prostheses were inserted and only one (1.8%) was lost, resulting in a prosthesis survival rate of 98.2%. The mean implant and prosthesis survival time was, respectively, 7.1 years and 6.3 years, according to the Kaplan-Meier survival analysis. A correlation was found between smoking and implant loss, which makes implant loss eight times more likely to occur in smokers than non-smokers. A significant association was also found between prosthesis loss and previous need of prosthesis repair. However, it was not considered clinically relevant. No association was found between the occurrence of adverse events and later implant or prosthesis loss. Conclusion High implant and prosthesis survival rates were found in the long term for treatment with extra-narrow implants. Moreover, a significant correlation between smoking and implant loss was observed.

Resumo Introdução A estabilidade primária é um importante indicador de sucesso da osseointegração. Porém, fatores locais com osso de baixa intensidade podem interferir negativamente na obtenção da estabilidade primária. Objetivo O presente estudo avaliou o efeito de diferentes direções, velocidades de rotação e sistemas de fresagem na expansão de perfurações e estabilidade de implantes instalados em blocos mimetizando osso do tipo IV. Material e método Foram instalados 50 implantes em blocos de poliuretano sólido rígido. Esses implantes foram igualmente divididos em cinco grupos (n = 10): 1) Fresa Maximus (utilizadas no sentido horário a 1200rpm); 2) Fresa Maximus (utilizadas no sentido horário a 600rpm); 3) Fresa Neodent (utilizadas no sentido horário a 800rpm); 4) Fresa Neodent (utilizadas no sentido anti-horário a 800rpm); 5) Fresa Neodent (utilizadas no sentido anti-horário a 600rpm). Foram executadas análises de estabilidade dos implantes através de testes de torque de inserção e remoção, além das análises de frequência de ressonância. Adicionalmente, a expansão associada às perfurações promovida pelas brocas foi avaliada por meio de análises tomográficas. Resultado Verificou-se que os implantes instalados após o preparo da perfuração com as brocas Maximus a 600rpm apresentaram valores de torque de inserção maiores, quando comparados ao grupo de implantes instalados em perfurações confeccionadas com brocas Neodent. Ademais, as brocas Maximus apresentaram valores de expansão maiores que as brocas Neodent. Conclusão As brocas Maximus são mais eficientes em promover a osseodensificação, e sua utilização está associada ao aumento da estabilidade dos implantes instalados em blocos mimetizando osso do tipo IV.

Abstract Introduction Primary stability is an important indicator to obtain a successful osseointegration. However, local factors like bone with low density can negatively interfere in obtaining primary stability. Objective This study assessed the effect of different drilling systems, speeds, and movement directions on the expansion of perforations and the stability of implants placed in blocks that mimicked type IV bone. Material and method Fifty implants were installed in rigid solid polyurethane blocks and equally divided into the following five groups (n = 10): 1) Maximus Driller (on a clockwise direction at 1200rpm); 2) Maximus Driller (on a clockwise direction at 600rpm); 3) Neodent Driller (on a clockwise direction at 800rpm); 4) Neodent Driller (on a counter clockwise direction at 800rpm); 5) Neodent Driller (on a counter clockwise direction at 600rpm). The stability analyses of the implants were performed through insertion and removal torque testing, in addition to resonance frequency analysis. Additionally, the expansion promoted by the drills associated with the perforations was assessed through tomographic analysis. Result We found that implants placed after drilling preparation with Maximus drills at 600 rpm had higher values of insertion torque than the group of implants installed in drillings made with Neodent drills. In addition, the maximus drills showed higher expansion values than the Neodent drills. Conclusion Maximus drills are more efficient in promoting osseodensification and their use was associated with increased stability of implants installed in blocks that mimicked type IV bone.

Abstract When periodontal disease is diagnosed, it is difficult to predict the clinical response of treatment of a tooth over time because the result of treatment is affected by several factors and will depend on the maintenance and support of periodontal treatment. Rehabilitation with removable dental prostheses, fixed prostheses, and dental implants makes it possible to restore the function and esthetics of patients with tooth loss due to periodontal disease. The predictive factors of tooth loss in periodontitis patients should be assessed by dentists to inform their clinical decision-making during dental treatment planning. This will provide detailed individualized information and level of risk of patients considered suitable for dental rehabilitation. Therefore, the aim of this article was to review the subject of “Impact of tooth loss due to periodontal disease on the prognosis of rehabilitation” and the effect of fixed, removable, and implant-supported prostheses in periodontal patients.

Resumo Introdução A investigação dos fatores indicadores de risco para as doenças peri-implantares auxilia na prevenção e direcionamento das técnicas de tratamento Objetivo O objetivo deste estudo transversal foi determinar a ocorrência de peri-implantite e seus potenciais fatores indicadores de risco, além de avaliar as taxas de sucesso e sobrevida em longo prazo dos implantes dentários após 8 a 10 anos de função Material e método Foram incluídos cinquenta indivíduos que receberam sua reabilitação implanto-suportada entre 2003 e 2005. Dados demográficos, história médica e odontológica foram coletados e um exame clínico completo foi realizado. A análise multivariada foi utilizada para identificar potenciais fatores indicadores de risco relacionados à ocorrência de peri-implantite. Ao todo, 211 implantes foram colocados; 197 estavam em função, 9 ainda estavam submersos e 5 haviam sido perdidos. Resultado As taxas de sucesso e sobrevivência foram de 81,5% e 97,6%, respectivamente. A mucosite peri-implantar afetou 77,1% dos indivíduos e 52,3% dos implantes. A peri-implantite foi diagnosticada em 14 indivíduos (29,2%) e 25 implantes (12,7%). Indivíduos com osteoporose (OR = 2,84) e sangramento generalizado à sondagem (OR = 8,03) foram significativamente associados a uma maior chance de peri-implantite. Ao nível do implante, a placa visível (OR = 4,45) e as maiores profundidades de sondagem (OR = 4,47) foram significativamente associadas à peri-implantite. Conclusão Por meio desses resultados, nosso estudo sugere que a osteoporose e a inflamação generalizada da mucosa periodontal / peri-implantar aumentam a probabilidade de peri-implantite.

Abstract Introduction The investigation of peri-implant diseases risk indicators helps to prevent and target treatment techniques. Objective The aim of this cross-sectional study was to determine the occurrence of peri-implantitis and its potential risk indicator factors, besides to assess the long-term success and survival rates of dental implants after 8 to 10 years of function. Material and method For this, fifty individuals who had received their implant-supported rehabilitation between 2003 and 2005 were included. Data regarding demographics, medical and dental history were collected and a complete clinical examination was performed. Multivariate analysis was used to identify potential risk indicator factors related to the occurrence of peri-implantitis. Overall, 211 implants had been placed; 197 were in function, 9 were still submerged, and 5 had been lost. Result Success and survival rates were 81.5% and 97.6%, respectively. Peri-implant mucositis affected 77.1% of subjects and 52.3% of implants. Peri-implantitis was diagnosed in 14 individuals (29.2%) and 25 implants (12.7%). Subjects with osteoporosis (OR = 2.84) and generalized bleeding on probing (OR = 8.03) were significantly associated with higher odds of peri-implantitis. At the implant level, visible plaque (OR = 4.45) and deep probing depths (OR = 4.47) were significantly associated with peri-implantitis. Conclusion Through these results, our study suggests that osteoporosis and generalized periodontal/peri-implant mucosa inflammation increase the likelihood of peri-implantitis.

Abstract Soft tissue defects around dental implants, such as papilla or volume loss, peri-implant recession and alterations of the ridge color and/or texture, lead to esthetic and functional complaints. Treatments of these defects in implants are more demanding than in teeth because peri-implant tissue exhibits different anatomical and histological characteristics. This narrative review discusses the proposed treatments for soft tissue defects around implants in the current literature. Several clinical and pre-clinical studies addressed methods to augment the quantity of the peri-implant keratinized mucosa. Autogenous grafts performed better than soft tissue substitutes in the treatment of soft tissue defects, but there is no clinical consensus on the more appropriate donor area for connective tissue grafts. Treatment for facial volume loss, alterations on the mucosa color or texture and shallow peri-implant recessions are more predictable than deep recessions and sites that present loss of papilla. Correction of peri-implant soft tissue defects may be challenging, especially in areas that exhibit larger defects and interproximal loss. Therefore, the regeneration of soft and hard tissues during implant treatment is important to prevent the occurrence of these alterations.

Resumo Introdução A utilização de substitutos ósseos em procedimentos de enxertia de forma alternativa ao uso do osso autógeno tem sido indicada, entretanto a comparação direta entre esses biomateriais tem sido pouco explorada. Objetivo Avaliar o efeito de diferentes biomateriais osteocondutores sobre o reparo de defeitos críticos em calvárias (DCC) de ratos. Material e método Foram utilizados 40 ratos que foram submetidos a confecção de um DCC com 8 mm de diâmetro. Os animais foram aleatoriamente divididos em 5 grupos com 8 animais, de acordo com o tipo de biomaterial utilizado para preencher os DCC: Grupo COA (coágulo); Grupo AUT (osso autógeno); Grupo OBD (osso bovino desproteinizado); Grupo HA/ TCP (cerâmica bifásica composta de hidroxiapatita e β fosfato tricálcio); Grupo TCP (β fosfato tricálcio). Foram executadas análise microtomográfica para avaliação do comprimento linear remanescente (DLL) do DCC e o volume dos tecidos mineralizados (MT) dentro do DCC nos períodos de 3, 7, 15 e 30 dias após cirurgia. Adicionalmente, foi executado análise histométrica para avaliar a composição do tecido ósseo reparado (% Osso e % Biomaterial) no período de 30 dias. Resultado O grupo COA apresentou o menor DLL e MT dentro do DCC e maior % osso do que os outros grupos. O grupo OBD apresentou maior volume de tecidos mineralizados e maior % biomaterial do que o grupo os grupos AUT e TCP. Os grupos OBD e AUT apresentaram maior % osso que o grupo TCP. Conclusão O OBD promoveu melhor padrão de aumento de disponibilidade óssea e qualidade do osso reparado em comparação ao TCP e HA/TCP, porém biologicamente inferior ao grupo AUT.

Abstract Introduction The use of bone substitutes in grafting procedures as an alternative of the use of autogenous bone graft has been indicated, however, the direct comparison between these biomaterials has been little explored. Objective To evaluate the effect of different osteoconductive bone substitutes on the bone repair in critical-sized defects (CSDs) in rat calvaria. Material and method One CSD with an 8 mm diameter was made in each of the 40 rats used in this study. The animals were randomly allocated into 5 groups (n=8), according to the type of bone substitute used to fill the CSD: COA (Coagulum); AUT (autogenous bone); DBB (deproteinized bovine bone graft); HA/TCP (biphasic ceramic composed of hydroxyapatite and β-phosphate tricalcium); and TCP (β-phosphate tricalcium). A microtomographic analysis was performed to evaluate the remaining defect linear length (DLL) of the CSD and the volume of the mineralized tissues (MT) within the CSD at 3, 7, 15 and 30 days after the surgical procedure. In addition, a histometric analysis was performed to evaluate the composition of the repaired bone tissue (% Bone and % Biomaterial) at the 30-day period. Result It was shown that the COA had the lowest DLL and MT within the CSD. In addition, the COA presented the highest % of bone in CSD. The DBB had a higher MT and a higher % of bone substitute particles in the CSD than the AUT and TCP groups. The DBB and AUT groups presented higher % of bone in the CSD than the TCP group. Conclusion The use of the DBB promoted a better pattern of bone volume gain and formation compared to TCP and HA / TCP but was biologically inferior to the AUT.

OBJETIVO: Analisar a estabilidade primária de implantes odontológicos com tratamento e sem tratamento de superfície, por meio da frequência de ressonância, utilizando diferentes materiais como substratos substitutos do osso humano para sua inserção. MÉTODOS: Foram utilizados 16 implantes de titânio Conexão(r), cilíndricos, hexágono externo, com 11,5 mm de comprimento e 3,75 mm de largura, sendo: 8 Master Porous, com tratamento de superfície; e 8 Master Screw, usinados. A instalação de implantes foi realizada nos seguintes substratos: osso de costela suína, madeira, osso artificial de poliuretana da marca Nacional(r) (40, 20 e 15 PCF) e da marca Synbone(r). Foi avaliada a estabilidade primária através da frequência de ressonância utilizando o aparelho Osstell(tm) Mentor. Os dados obtidos foram submetidos a tratamento estatístico ANOVA e Teste de Tukey, com nível de significância a 5%. RESULTADOS: Foi constatado que, apesar de Master Porous apresentar maior valor que Master Screw em todos os substratos, estes não apresentaram diferença estatística entre si (p>0,05), com exceção da poliuretana Nacional(r) de 20 PCF. Quando inseridos no substrato madeira e na poliuretana Nacional(r) 40 PCF, Master Porous e Master Screw tiveram maiores valores. Master Porous, quando inserido no osso suíno também foram iguais estatisticamente a estas interações. CONCLUSÃO: Apesar de inovações nas características das superfícies de implantes serem desenvolvidas constantemente para contribuir no desempenho de implantes osseointegrados, e nosso estudo encontrar que não houve influência do tratamento de superfície na estabilidade primária aferida por frequência de ressonância; ainda há pouco conhecimento científico sobre esses efeitos.

OBJECTIVE: The aim of this study was to analyze the primary stability of dental implants with and without surface treatment, by means of resonance frequency, using different materials as substitutes for human bone substrates for insertion. METHODS: Sixteen external hexagon, cylindrical Conexão(r) titanium implants were used, 11.5 mm long by 3.75 mm wide, as follows: 8 Master Porous (MP), with surface treatment and 8 Master Screw (MS) machined. The implant placement was performed on the following substrates: pork rib bone, wood, artificial bone polyurethane National(r) (40, 20, 15 PCF) and Synbone(r). Primary stability was assessed via resonance frequency using an Osstell Mentor(tm) device. Data were analyzed statistically using ANOVA and Tukey's test, with a significance level of 5%. RESULTS: It was found that although MP and MS have a higher value on all substrates, these were not statistically different between groups (p>0.05), except for polyurethane National(r) 20 PCF. When inserted into the wood substrate and polyurethane National(r) 40 PCF, MP and MS had higher values. MP, when inserted into the pig bone, was also statistically equal to these interactions. CONCLUSION: Despite the continuous development of innovations in the characteristics of implant surfaces to assist with the performance of osseointegrated implants, and the fact that our study has found that the surface treatment had no impact on the primary stability checked using ressonance frequency, there is still very little scientific understanding of these effects.

AIM: To evaluate the influence of the format and surface treatment of implants, as well as the substrate used in primary stability. METHODS: Thirty-two Conexão® implants were used: 8 conical (CC) (11.5 x 3.5 mm) and 24 cylindrical (11.5 x 3.75 mm) - 8 external hexagon implants without surface treatment (MS), 8 external hexagon implants with double Porous treatment (MP), 8 internal hexagon implants with Porous treatment (CA). They were inserted in Nacional® polyurethane in three densities (15, 20 and 40 PCF). The insertion torque (IT) (N.cm) was quantified using the digital Mackena® torque meter, and the pullout force (PF) (N) by means of axial traction force with a 200 kg load cell, performed in a Universal Test Machine (Emic® DL10000) and the Tesc 3.13 software. Data were analyzed statistically by ANOVA and Tukey's test with a significance level of 5%. RESULTS: Difference was observed between groups (p<0.05). Regarding the IT, MP and MS inserted to the substrate 40PCF showed higher values with statistically significant difference with all interactions implants x substrate; the 15 and 20PCF densities was not significant in all groups of implants. MP, MS, CC and CA did not differ significantly, even inserted in a lower density, where CC showed better IT compared with other densities. For PF, the best performance was the interaction implant CA x 40PCF substrate, showing a difference from the other implants inserted in all substrates. CONCLUSIONS: The higher bone density and cylindrical implants with surface treatment provides greater IT and PF.

OBJETIVO: A proposta do estudo foi avaliar a influência do formato e do tratamento de superfície na estabilidade primária de implantes odontológicos, inseridos em diferentes substratos, utilizando-se associação de métodos, como torque de inserção, resistência ao arrancamento e frequência de ressonância. MATERIAL E MÉTODO: Foram utilizados 32 implantes da marca Conexão® (Conexão Sistemas de Prótese Ltda, Arujá, São Paulo, Brasil), sendo: oito cilíndricos com tratamento Porous (CA), oito cilíndricos usinados (MS), oito cilíndricos tratamento duplo Porous (MP) e oito cônicos sem tratamento (CC). Os substratos utilizados para inserção foram: costela de porco; poliuretana Synbone©; poliuretana Nacional® (15, 20, 40 PCF), e madeira. O torque de inserção (TI) foi quantificado utilizando-se um torquímetro digital Kratos®; a força de arrancamento (RA) foi aferida por meio de tração axial, realizada em uma Máquina Universal de Ensaios (Emic® DL-10000), e utilizou-se também análise por meio de frequência de ressonância (RF). Para obtenção dos resultados estatísticos, utilizou-se análise de variância e teste de Tukey (significância de 5%). RESULTADO: Ao analisar o torque de inserção, verificou-se que os implantes com tratamento de superfície não foram diferentes estatisticamente dos usinados, assim como os implantes cilíndricos não tiveram diferença dos cônicos em todos os substratos (p>0,05), com exceção da poliuretana Synbone©. Em relação à resistência ao arrancamento, os implantes tratados e usinados, assim como cônicos e cilíndricos, não tiveram diferença estatística (p>0,05); a análise de frequência de ressonância mostrou que não houve diferença entre os implantes (p>0,05), com exceção da poliuretana Nacional® (20 PCF). CONCLUSÃO: Os formatos e o tratamento de superfície estudados não demonstraram valores significantes quando foram comparados os implantes entre si e, considerando os substratos avaliados, não houve diferença estatística entre os diferentes tipos de implantes.

OBJECTIVE: The purpose of the study was to evaluate the influence of the shape and surface treatment on the primary stability of dental implants inserted in different substrates through association methods such as insertion torque, pullout strength and resonance frequency. MATERIAL AND METHOD: 32 implants were used with 8 cylindrical treatment Porous (CA), 8 machined cylindrical (MS), 8 cylinder dual treatment Porous (MP) and 8 tapered untreated (CC). The substrates used for inclusion were: pork rib; © Synbone polyurethane, polyurethane National ® (15, 20, 40 PCF) and wood. The insertion torque (TI) was quantified using a digital torque Kratos® wrench, the pullout strength (RA) was measured by means of axial traction performed in an Emic DL-10000® and analysis was also used by the resonance frequency (RF). To obtain the statistical results, we used analysis of variance and Tukey's test (5% significance). RESULT: To analyze the insertion torque, it was found that implants with surface treatment were not statistically different from machined as well as the cylindrical implants did not differ from tapered on all substrates (p>0.05), except © Synbone of polyurethane; in relation to RA, treated and machined implants as well as tapered and cylindrical, showed no statistical difference (p>0.05); FR analysis showed no difference between implants (p>0,05), with the exception of National® polyurethane (20 PCF). CONCLUSION: formats and surface treatment studied showed no significant values when compared implants together and considering the tested substrates showed no statistical difference between the different types of implants.