Cobalt catalysts supported on γ-alumina, ceria and γ-alumina-ceria, with 10 or 20%wt of cobalt load, prepared by the wet impregnation method and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), field emission transmission electron microscopy (FETEM), N2 adsorption-desorption isotherms (BET/BJH methods), energy-dispersive X-ray spectroscopy (EDX), X-ray photoemission spectroscopy (XPS), O2-chemisorption and temperature programmed reduction (TPR) were used to promote the oxidation of volatile organic compounds (n-hexane, benzene, toluene and o-xylene). For a range of low temperatures (50-350 °C), the activity of the catalysts with a higher cobalt load (20% wt) was greater than that of the catalysts with a lower cobalt load (10% wt). The Co/γ-Al2O3-CeO2 catalytic systems presented the best performances. The results obtained in the characterization suggest that the higher catalytic activity of the Co20/γ-Al2O3-CeO2 catalyst may be attributed to the higher metal content and amount of oxygen vacancies, as well as the effects of the interaction between the cobalt and the alumina and cerium oxides.

Pb/Ti, Sn and Mg-based nanocomposite materials were prepared by the high-energy mechanical milling of commercial powders. The surface of these ceramic compounds was strongly influenced by the doping, diameter of the milling spheres and time of the mechanical milling (amorphization process). Such milling leads to the formation of nanocrystalline materials. The mechanical processing parameters of these compounds were investigated through Brunauer, Emmett and Teller isotherms, wide angle X-ray diffraction, transmission electron microscopy and CO2 adsorption.

Neste trabalho foi investigada a preparação de carbonos ativados através da pirólise de composições elastoméricas provenientes de resíduos de bandas de rodagem de pneus de automóveis. O material foi processado nas temperaturas de 500, 620 e 700 °C, em atmosfera de N2, utilizando-se o hidróxido de potássio como agente ativador. Os produtos resultantes foram caracterizados pela fisisorção de N2 a 77 K, através de isotermas de Brunauer, Emmet e Teller e por microscopia eletrônica de varredura. Esses carbonos ativados apresentam estruturas típicas de sólidos mesoporosos e a temperatura de pirólise tem grande influência na área específica e distribuição de volume de poros. O carbono ativado obtido a 700 °C apresentou maior área específica e estrutura porosa compacta. Esse material apresenta melhor desempenho frente à adsorção de azul de metileno, removendo até 1,0 x 10-1 g de corante por grama de carbono utilizado, em tempos inferiores a 300 s.

In this work, the preparation of activated carbons through the pyrolysis of elastomers, arising from car threads of tire waste, was investigated. The material was processed at 500, 620 and 700 °C, under N2 atmosphere, by using potassium hydroxide as activating agent. The resulting products were characterized by physisorption of N2 at 77 K, through Brunauer, Emmet and Teller isotherms, and scanning electron microscopy. The carbons obtained display a characteristic structure of mesoporous materials and the pyrolysis temperature has strong influence on the specific area and porous volume distribution. The activated carbon obtained at 700 °C has high specific area and compact structure. It exhibited high performance for adsorption of methylene blue solution, removing 1.1 x 10-1 g of the dye per gram of carbon in less than 300 s.

Neste trabalho é apresentada a reação de condensação aldólica entre metanol e acetona promovida por nanopartículas de dióxido de estanho, não dopadas e dopadas com as terras raras Ce e Y. Diversas condições de relação molar metanol/acetona foram avaliadas, objetivando a obtenção com elevada seletividade do composto a, b-insaturado, metil vinil cetona. As nanopartículas foram preparadas empregando-se o método dos precursores poliméricos. As amostras foram caracterizadas por meio de adsorção de N2 para determinação de área superficial específica (BET), difração de raios X (DRX), adsorção química de CO2, espectroscopia de fotoelétrons (XPS) e microscopia eletrônica de transmissão (MET). O comportamento catalítico observado para as amostras de SnO2 sugere que a relação molar metanol/acetona e a dopagem com as terras raras desempenham um papel importante na atividade catalítica do material e na seletividade aos produtos reacionais. Os resultados de DRX e XPS apontam para a formação de uma camada de segregação, para as amostras dopadas, devido ao tratamento térmico imposto. Essa camada de segregação afeta diretamente o comportamento catalítico do material frente à reação de condensação.

Aldol condensation between methanol and acetone, catalyzed by undoped and rare earths (Ce and Y) doped tin oxide nanoparticles is presented. Several methanol/acetone molar ratio conditions were evaluated aiming to produce methyl vinyl ketone as the main product. The undoped and doped ultrafine nanoparticles of tin oxide were prepared using the polymeric precursor method. The characterization was carried out by means of N2 adsorption (BET), X-ray diffraction (XRD), CO2 chemisorption, X-ray photoemission spectroscopy (XPS) and transmission electron microscopy (TEM). The catalytic behavior observed for SnO2 samples suggests that the methanol/acetone molar ratio and Ce and Y doping play an important role in the catalytic activity and in the product selectivity. The results from XRD and XPS pointed to the de-mixing process for the doped samples, due to the heat-treatment. This segregation layer contributes to the observed change in the catalytic behavior.

The CO2 reforming of CH4 was carried out over Ni catalysts supported on γ -Al2O3 and CeO2-promoted γ -Al2O3. The catalysts were characterized by means of surface area measurements, TPR, CO2 and H2 chemisorption, XRD, SEM, and TEM. The CeO2 addition promoted an increase of catalytic activity and stability. The improvement in the resistance to carbon deposition is attributed to the highest CO2 adsorption presented by the CeO2 addition. The catalytic behavior presented by the samples, with a different CH4/CO2 ratio used, points to the CH4 decomposition reaction as the main source of carbon deposition.

Neste trabalho são apresentados os procedimentos de preparação de materiais cerâmicos de SiO2, SnO2 e Al2O3 e, também, suas propriedades catalíticas nas reações de reforma do metano e do metanol. As análises dos resíduos de carbono, após testes catalíticos, sugerem que a modificação estrutural dos catalisadores pode minimizar os efeitos de sua desativação.

This work presents the procedures for preparing SiO2, SnO2 and Al2O3 ceramic materials and also their catalytic properties for the reforming reactions of methane and methanol. The analyses of the carbonaceous residues suggest that the structural modification of the catalyst can minimize the deactivation effect upon them.