Resumo em Inglês:

The origin of the sedimentary organic matter in the Mundaú-Manguaba estuarine system was evaluated through the distribution and composition of sterols, alcohols and ancillary data. The muddy sediments of the lagoons are enriched in organic matter, derived from a mixture of autochthonous and allochthonous inputs. Mundaú exhibited moderate contamination by sewage, with coprostanol concentration as high as 4.4 µg g-1. The channels are characterized by sand and organic matter-poor sediments. The sediments from some rivers in the drainage basin accumulated organic matter derived only from terrestrial vegetation. Stanol/sterol ratios evidenced the preferential diagenesis of the autochthonous fraction of organic matter.

Resumo em Inglês:

A sequential batch reactor (4 L) inoculated with Aspergillus niger was operated in order to remove congo red dye (10 mg L-1). The feeding of the reactor was done to each 7 days. The glucose was added in the concentration of 1 g.L-1 (Stage I) and 0.5 g L-1 (Stage II). The Stage III occurred without glucose addition. The Stage I was great to process, because the system reached the greater dye removal (95%) as well as the kinetic parameters ware the best - K M (0.7 g L-1) and k1 (0.025 h-1).

Resumo em Inglês:

A simple ion pair-dispersive liquid-liquid microextraction method was proposed for preconcentration trace amounts of rhodium. An ion association complex of RhCl4- and tetradecyldimetylbenzylamonium was extracted into cholorobenzene. The volume and the type of extractive and dispersive solvents, the extraction time and the pH of the aqueous solutions were optimized. The calibration curve was linear in the range of 0.6-500 ng mL-1 of rhodium. The limit of detection was 0.10 ng mL-1 in initial solution and preconcentration factor was 40. The proposed method was successfully applied to the extraction and determination of rhodium in road dust and water samples.

Resumo em Inglês:

A preliminary analyses of the possible contamination of surface and groundwater by the active ingredients of the pesticide products used in the areas with intensive agricultural activities of Alto Paranaíba region, MG, Brazil, was carried out. The active ingredients and formulated products most used in the region were identified and their characteristics of environmental importance were presented. The EPA screening criteria, the groundwater ubiquity score (GUS) and the criteria proposed by Goss were used to evaluate which pesticides might contaminate the local waters. Among the active ingredients studied, several present risks to the local aquatic environment.

Resumo em Inglês:

A rapid analytical approach, suitable to characterize the compounds present in the aqueous and methanol extracts prepared from the aerial parts of Indigofera hirsute, was developed. The method based on high-performance liquid chromatography coupled to mass spectrometry, electrospray positive ionization and detection by time of flight (HPLC-ESI-MS-TOF) identified, tryptophan, uracil, rutin, kaempferol-3-O-β-D-glucopyranoside, gallic acid and methyl gallate. The antiradical activity of this extract was evaluated using DPPH assay, with gallic acid as antiradical pattern. The study revealed the antiradical activity of methyl galatte (EC50 = 5 ± 0.3 µg mL-1) galic acid (EC50 = 5 ± 0.2 µg mL-1) and rutin (EC50 = 21.6 ± 0.6 µg m L-1), isolated from methanol extract (EC50 = 67.7 ± 0.9 µg mL-1), which showed strong antiradical activity.

Resumo em Inglês:

The inactive biomass of fungus Aspergillus niger O-5 obtained in Cuba was characterized as sorbent of Pb2+ by several structural analysis and others techniques. In addition, the biomass was studied for the separation / preconcentration of Pb2+ from aqueous solution. The maximum biosorption capacity was obtained for the contact time of 30 min and pH 5. The kinetic of sorption process occurred according to the model of Ho. The Freundlich or Langmuir models suitably described the experimental adsorption isotherms. The biomass can be used as sorbent for Pb2+ with a maximum capacity of 4.7 - 6.2 mg g-1. The pretreatment with NaOH solution improved its sorption capacity.

Resumo em Inglês:

We describe the synthesis of 12 new ethyl and methyl quinoxaline-7-carboxylate 1,4-di-N-oxide derivatives on solid supports with room temperature and microwave-assisted solvent-free procedures. Results show that solid supports have good catalytic activity in the formation of quinoxaline 1,4-di-N-oxide derivatives. We found that florisil and montmorillonite KSF and K10 could be used as new, easily available, inexpensive alternatives of catalysts. Additionally, room temperature and microwave-irradiation solvent-free synthesis was more efficient than a conventional procedure (Beirut reaction), reducing reaction time and increasing yield.

Resumo em Inglês:

The major applications of organoclays are in adsorption of organic polluents. The objective of this work was the synthesis and characterization of organoclays using differents amounts of cationic surfactant hexadecyltrimethylammonium bromide. The clays were characterized by low angle x-ray diffraction (XRD), scanning electron microscope (SEM), infrared with Fourier tranformation (FTIR), BET surface area, elemental analysis (CHN), Foster swell and adsorption of methylene blue. The surfactant can adsorb in differents forms in the interlamelar region changed the basal spacing. The presence of the surfactant adsorbed can be favorable or not in adsorption of the methylene blue due the different interactions dye-organoclays.

Resumo em Inglês:

In situ ethylene polymerizations were performed using bis(cyclopentadiene)titanium dichloride supported on polyethersulfone as catalyst. The bis(cyclopentadiene)titanium dichloride supported on polyethersulfone catalyst activity estimated by ethylene polymerization was 360 kgPE/molTi/h. During polymerization the fillers used were montmorillionite nanoclays having surface modifications with 35-45 wt% dimethyl dialkyl(14-18)amine (FA) and 25-30 wt% trimethyl stearyl ammonium (FB). These fillers were pretreated with methylaluminoxine (MAO; cocatalyst) for better dispersion onto the polymer matrix. The formation of polyethylene within the whole matrix was confirmed by FTIR studies. It was found that the nature of nanofiller did not have any remarkable effect on the melting characteristics of the polymer. TGA study indicates that nanoclay FB filled polyethylene has higher thermal stability than nanoclay FA filled polyethylene. The melting temperature of the obtained polyethylenes was 142 ºC, which corresponds to that synthesized by the polyether sulfone supported catalyst.

Resumo em Inglês:

Cellular metals are a new class of materials with promising applications and a unique combination of physical, chemical and mechanical properties. The Al-356 alloy is used to manufacture metal foams from NaCl preforms. Despite the usefulness of these materials, their performance may be affected by corrosion due to residual salt. This paper reports the study of the behavior of the Al-356 alloy in chloride solutions by electrochemical techniques in rotating disk electrode. The cathodic reaction of oxygen reduction is the crucial stage of process dissolution of the material, which shows that is the oxygen transport which limits the corrosion process.

Resumo em Inglês:

This paper describes the development of methods for the determination of Pb and Mn in fishes by GF AAS after solubilization with tetramethylamonium hidroxide. The optimization of the operational conditions and the choice of modifier were made using multivariated optimization. Analytical Figures of Merit were adequately to propose. The Limit of Quantification obtained were 150 and 18.5 µg kg-1 to Mn and Pb, respectively. No significant difference was found between the slope values obtained for the aqueous and standard addition calibration curves. The D.P.R. was always lower than 12% and the analysis of the SRM NRCC TORT2 showed 80-120% of recovery.

Resumo em Inglês:

TiO2 thin films were prepared by the sol-gel method using different acids (HCl and HAc), with a parallel evaluation of the gel ageing effects on the film properties. After the thermal treatments, the resulting materials were characterized through gravimetric analysis, UV-VIS spectrophotometry (from which optical parameters such as band gap was derived), XRD, morphological surface analysis (AFM) and photocatalytic activity. The majority of the obtained thin films parameters were similar independent of the acid type and the ageing time of the gel. Nevertheless, a visible effect of the surface morphology properties on the films and their photocatalytic activity was observed.

Resumo em Inglês:

In this work, a rapid and simple method using capillary electrophoresis (CE) was developed for the determination of the benzoate, sorbate, methyl and propylparaben in foodstuffs. A running buffer consisting of 20 mmol L-1 (pH = 9.3) tetraborate enabled separation of the analytes in less than 5 min. The detector wavelength was set at 220 nm. The method was successfully applied to the analysis of sodas, sweeteners, sauces and juices. The range of preservatives found were from 478.5-466.6 mg kg-1 for methylparaben , 83.7-231.3 mg kg-1 for sorbate and 336.7-428.3 mg kg-1 for benzoate.

Resumo em Inglês:

The phytochemical investigation of the stem bark and leaves of G. elliptica provided a mixture of the norisoprenoids blumenol B and 6-epiblumenol B along with the triterpenes friedelin, as the major constituent, friedelanol, ursa-9(11),12-dien-3-ol, a-amyrin, β-amyrin, morentenol, epifriedelanol, as well as the sesquiterpenes trans-caryophyllene, α-humulene, ethyl hydnocarpate and other fatty acid esters. The identification of the compounds was performed on basis of spectrometric methods such as GC-MS, IR, MS and 1D and 2D NMR. Stem bark extracts showed significant leishmanicidal activity against promastigote forms of Leishmania braziliensis, with the best results for the chloroform extract.

Resumo em Inglês:

The growth of biodiesel market and the implementation of regulations related to biodiesel production and biodiesel/diesel blending has encouraged the development of appropriate analytical methods to control the composition of this type of mixture. In this study, an evaluation of the potential of GC×GC for the characterization of samples of beef tallow biodiesel and the composition of blends of biodiesel/diesel is presented. The methodology was applied to beef tallow biodiesel and its mixtures with petrodiesel, ranging from B2 to B50. Results allowed not only the identification and quantification of the biodiesel esters, but also the biodiesel percentage in biodiesel/diesel blends.

Resumo em Inglês:

This work compared activated carbon, activated earth, diatomaceous earth, chitin and chitosan to removal acid blue 9, food yellow 3 and FD&C yellow nº 5 dyes from aqueous solutions with different pH values (2-10). In the best process condition for each dye, equilibrium studies were carried out at different temperatures (from 298 to 328 K) and Langmuir, Freundlich, Redlich-Peterson, Temkin and Dubinin-Radushkevich models were fitted with experimental data. In addition, entropy change, Gibbs free energy change and enthalpy change were obtained in order to verify the thermodynamic adsorption behavior.

Resumo em Inglês:

Leaves and flower heads of P. brevipedunculata were submitted to four drying-air temperatures (room temperature, 40, 50 and 60 ºC). Room temperature (approximately 30 ºC) and higher temperature drying (50 and 60 ºC) had a deleterious effect on the essential oil content. The recommended drying-air temperature for the species is 40 ºC for it results in the same amount of essential oil observed in fresh cut plants. Overall, 13 components accounting for more than 92% of the total composition were identified. Citral was the major component, followed by α-pinene and limonene. The essential oil showed high toxicity against Artemia salina larvae.

Resumo em Inglês:

A flow system based on the sandwich technique is proposed for the sequential determination of ascorbic acid, dipyrone, acetylcysteine, captopril and paracetamol. The procedure is based on the reduction of Cu(II) by the analytes followed by the spectrophotometric measurement of the complex of Cu(I) with 2,2'-biquinoline 4,4'-dicarboxylic acid. Linear responses were achieved in the µmol L-1 range, with coefficients of variation better than 1.7%. Sampling rate was estimated as 60 determinations per hour, consuming 230 µg of BQA and generating 2.5 mL of waste per determination. Results for commercial samples agreed with those obtained by procedures recommended by the American and European pharmacopeias at the 95% confidence level.

Resumo em Inglês:

The objective of this study was to evaluate the toxic effect of Cu2 + in the physiological development of E. gracilis. The results showed that E. gracilis had an effect on the dose-dependent growth to the concentration of metal. The exposure of E. gracilis metal at doses of 0.8 and 1.6 mM of Cu2+ showed a significant negative effect on the stability of DNA and photosynthetic pigments involved in capturing light in the antenna complex after 144 h of exposure to the metal.

Resumo em Inglês:

One of the most important aspects of chitosan' derivatization depends on the crosslinking of their polymeric chains. This chemical strategy may confer new properties to those derivatives, which can be used to enhance their biotechnological applications. So far, this work aims to discuss some strategies related to the crosslinking of chitosan focusing on reagents, reaction mechanisms and properties/applications of the crosslinked derivatives in several fields of science.

Resumo em Inglês:

Several matters of the pharmaceutical demonstrate the great importance of thermal analysis application, especially TG and DSC for the pharmaceutical industry future, namely: characterization of the drugs with the thermal events definition, in studies of drug purity, in the polymorphs identification, in compatibility studies of solid dosage pharmaceutical formulations, in drugs and pharmaceutical formulations thermal stability, and in determination of shelf life for isothermal degradation kinetics by extrapolation using the Arrhenius equation. Thus, the test results obtained from thermal analysis are directly related to the quality of a pharmaceutical product, whether the stability or bioavailability of the pharmaceutical product.

Resumo em Inglês:

This paper presents a historical of the Biosilicate®, a bioactive glass-ceramic developed at the Vitreous Materials Laboratory of the Federal University of São Carlos, Brazil. After decades of study accomplished with bioactive glasses and glass-ceramics, Biosilicate® results from a natural evolution and has similar bioactivity index, but far superior mechanical properties than of all bioactive glasses. Biosilicate® is almost fully crystalline and also exhibits much higher bioactivity than all the currently commercially available bioactive glass-ceramics. Due to its special characteristics, Biosilicate® has been successfully tested for several medical and dental applications as we thoroughly discuss in this review paper.

Resumo em Inglês:

A sugar cane mill is at the present moment a modest biorefinery producing few products such as sugar, ethanol and polyhydroxybutyrate (PHB). In the near future, this mill can expand its production using several renewable feedstock's to produce biofuels and high value biobased chemicals. However, the choice of appropriate products for addition to the portfolio is challenged by a lack of broad-based conversion technology coupled with a plethora of potential targets. The intent of this revision was to catalyze research efforts to expand the list of products and to present an updated evaluation of potential target structures for chemical production.

Resumo em Inglês:

A rapid and low cost method to determine Cr(VI) in soils based upon alkaline metal extraction at room temperature is proposed as a semi-quantitative procedure to be performed in the field. A color comparison with standards with contents of Cr(VI) in the range of 10 to 150 mg kg-1 was used throughout. For the different types of soils studied, more than 75% of the fortified soluble Cr(VI) were recovered for all levels of spike tested for both the proposed and standard methods. Recoveries of 83 and 99% were obtained for the proposed and the standard methods, respectively, taking into account the analysis of a heavily contaminated soil sample.

Resumo em Inglês:

A method based on headspace - solid phase microextraction coupled with gas chromatography - mass spectrometry was validated for the quantitative determination of 18 organochlorine pesticides in water. For the extraction conditioning some parameters as the best type of coating fiber, time and temperature of extraction, pH and ionic strength were evaluated. The method HS-SPME/GC-MS/MS showed linear coefficient above 0.9948. The repeatability of the measurements were lower than 7.6%. Relative recoveries were between 88 and 110%. Limits of detection from 0.5 x 10-3 to 1.0 mg L-1 were obtained. A total of 31 samples were analyzed and 16 presented from 1 to 5 pesticides.

Resumo em Inglês:

This work reports the optimization and method validation for sulfonamides (sulfamethazine, sulfaquinoxaline, sulfadimethoxine and sulfathiazole) in shrimp muscle using HPLC-UV. The sulfonamides were extracted with acetonitrile and acetic acid, and the extract cleaned up with a Strata SCX SPE cartridge prior to analysis. The method presented linearity in the range of 20-120 µg kg-1, good linear correlation (r > 0.99), and limits of quantification in the range of 4.7-20.2 µg kg-1. The recovery for shrimp muscles spiked with 50-150 µg kg-1 ranged from 63.2-108.0%. Precision and accuracy analysis showed acceptable relative standard deviation. Commercial shrimps were analyzed and sulfonamides don't were found above of the method limit of quantification.

Resumo em Inglês:

A simple and rapid ultra-performance liquid chromatographic method for determination of oseltamivir in capsules was developed and validated. The mobile phase consisted of 5 mmol/L triethylammonium buffer (pH 3.0) and acetonitrile (70:30, v/v). Separation was performed in a Hypersil Gold® column, with octylsilil as stationary phase (100 x 2.1 mm, p.d. 1.9 µm). Chromatography run time was 1.2 min. The method presented adequate specificity, linearity, precision, ruggedness and accuracy and was adequate for determination of oseltamivir in capsules.

Resumo em Inglês:

This article describes a Problem-Based Learning (PBL) experience that taught organophosphorus pesticides chemistry, its human health effects and acetylcholinesterase assay to secondary students. The teaching process was based on a real intoxication case and ended with students' activities report presentation. The apparent lack of teacher reference and inexistence of a curriculum based on a strict textbook in which PBL is based on leads inexperienced students to insecurity and the idea that teachers are not doing there jobs. One way to minimize this situation is to use real cases in other to interest students as stakeholders of central problem solution.

Resumo em Inglês:

This research was conducted in a research network in teaching science/chemistry, as an alternative for initial and continuing teacher formation. The network is composed by teachers in initial formation, teacher trainers and teachers of basic education of the various areas of science. Assuming the socio-historical perspective, the discourse coming from the social interaction between the collective of teachers, was the object of study. We present an analysis of the interactions of the speech and reflections about the appropriation of scientific/chemical as a social practice mediated by language supplement our results.

Resumo em Inglês:

In this paper it is proposed an indirect method to evaluate the corrosion rate of an aluminum and zinc alloy in alkaline solution by using a well-known device for collecting gases over water. The hydrogen gas formation, a corrosion product, is monitored at different time intervals and associated with the alloy mass loss. It has been suggested that the students should work in groups, which may make feasible the social interaction among them and that results discussion may be done collectively under a professor orientation. This proposal may propitiate the learning of terminology and involved concepts as well as contribute to a better understanding of corrosion phenomena that occur in their everyday life.

Resumo em Inglês:

The role of the logistics in the design of synthetic pathways aimed at greenish is discussed. The influence on costs (of reagents, solvents and total), as well as on atomic productivity green metrics (atomic economy and E factor), of the position along the pathway of a step with low yield, or involving high dilution of the reagents or expensive reagents, has been evaluated by calculations on a linear pathway model. The results show the economic importance of Green Chemistry and provide useful information for pathway design or improvement.