Influence of elastic modulus of intraradicular posts on the fracture load of roots restored with full crowns

Influência do modulo de elasticidade de retentores intrarradiculares na carga para fratura de raízes restauradas com coroas totais

Abstract

Objective

This study aimed to evaluate the fracture load and displacement of roots restored with posts of different elastic modulus.

Material and method

Thirty-six replicas of epoxy resin mixed with glass microfibers were made from an endodontically-treated human premolar root prepared to a length of 12 mm with a custom drill, leaving the apical 4 mm unprepared. Replicas were randomly restored with (n = 12): FP-LM (fiber post with low elastic modulus– 50 GPa), FP-HM (fiber post with high elastic modulus – 67 GPa) and MP (metallic post – 208 GPa), using self-curing adhesive and dual resin cement. Cores were built up with composite resin and metallic crowns were cemented in all the roots with self-adhesive resin cement with self-curing mode. Specimens were subjected to a fracture load test (45° inclination/0.5 mm/min) and displacement was registered at 100 N.

Result

One-way ANOVA showed that elastic modulus of the post did not affect the fracture load means (p = 0.203) (FP-LM: 237.4 ± 65.11 N; FP-HM: 236.7 ± 92.85 N; MP: 295.8 ± 108.7 N) but was statistically significant for the displacement (p < 0.00): Tukey’s test showed that FP-LM displacement mean (0.81 ± 0.15 mm) was significantly higher than those for FP-HM (0.46 ± 0.26 mm; p = 0.00) and MP (0.62 ± 0.07 mm; p = 0.04).

Conclusion

Posts with different elastic modulus exhibit similar fracture loads, but a lower displacement is achieved when fiber posts with a high elastic modulus and metallic posts are used.

Descriptors:
Compressive strength; intraradicular posts; dental materials; dental prosthesis

Resumo

Objetivo

Este trabalho avaliou a carga para fratura e deslocamento de raízes restauradas com pinos de diferentes módulos de elasticidade.

Material e método

Trinta e seis réplicas de microfibras de vidro embutidas em resina epóxi foram fabricadas a partir de uma raiz de um pré-molar tratado endodonticamente preparado em 12 mm de comprimento com brocas customizadas, deixando 4 mm apicais sem preparo. As raízes foram randomicamente restauradas com (n = 12): FP-LM (pino de fibra com um baixo módulo de elasticidade – 50 GPa), FP-HM (pino de fibra com um alto módulo de elasticidade – 67 GPa) e MP (pinos metálicos – 208 GPa), usando adesivo autopolimerizável e cimento resinoso dual. Núcleos foram confeccionados com resina composta e coroas metálicas foram cimentadas em todas as raízes com cimento resinoso autoadesivo com modo de polimerização químico. Os espécimes foram submetidos ao teste de fratura em 45° (inclinação de 45° / 0,5 mm/min) e o deslocamento foi registrado aos 100 N.

Resultado

Anova 1 fator mostrou que o módulo de elasticidade dos retentores não afetou as médias de fratura (p = 0,203) (FP-LM: 237,4 ± 65,11 N; FP-HM: 236,7 ± 92,85 N; MP: 295,8 ± 108,7 N) mas foi estatisticamente significante para o deslocamento (p < 0,00): o teste de Tukey mostrou que a média de deslocamento do grupo FP-LM (0,81 ± 0,15 mm) foi significativamente maior do que o grupo FP-HM (0,46 ± 0,26 mm; p = 0,00) e MP (0,62 ± 0,07 mm; p = 0,47).

Conclusão

Pinos com diferentes módulos de elasticidade mostram resistência similar, porém um menor deslocamento é obtido quando pinos de fibra com alto módulo de elasticidade (FP-HM/MP) são usados.

Descritores:
Força compressive; retentores intrarradiculares; materiais dentários; prótese dentária

INTRODUCTION

The proper esthetic and functional reconstruction of endodontically treated teeth is a crucial factor for long-term success of the rehabilitation¹. Endodontically treated teeth commonly present substantial destruction of tooth structure resulting from caries, dental fracture and cavity preparation for endodontic therapy, making the retention of restorative materials difficult². When there is loss of more than half of the coronal structure, intraradicular posts are recommended to retain the restorative materials used to reconstruct the tooth crown and to distribute stress along the root^3,4. However, intraradicular posts do not reinforce the remaining dental structure³.

To select the most suitable post it is necessary to consider many factors like the position of the tooth, degree of dental destruction and type of restoration to be placed⁵. Different post systems options with diverse elastic modulus are available for restoration of endodontically treated teeth. Cast post and cores and, more recently, prefabricated metallic posts have been used. According to finite element analyses, such posts with an elastic modulus superior to that of dentin concentrate high stress on the radicular dentin, which may increase the risk of root fracture⁶. Carbon and glass fiber posts were developed as an alternative to metallic posts to improve esthetics and adhesion to the dental structure. Due to mechanical properties similar to dentin, fiber posts transmit less stress to the remaining dentin and decrease the risk of root fracture since it is likely that the post/core will fail before the root fractures⁶.

Although the rigidity of the intracanal anchorage should be taken into consideration since it may influence the mechanical behavior of the restored endodontically treated teeth⁶, most studies which evaluated the fracture strength of teeth restored with different post materials used diverse post systems with varied shapes and diameters^1,7,8, making it difficult to isolate the variable “post rigidity”. For this reason, this study focused on the evaluation of posts with the same format.

Thus, the purpose of this in vitro study was to evaluate the effect of different elastic modulus of intraradicular posts on the fracture load and displacement of roots restored with full crowns. The hypotheses tested were that different elastic modulus would generate similar fracture load and would not affect displacement of the restored teeth.

MATERIAL AND METHOD

A single-root human premolar extracted for orthodontic reason with no caries, no previous endodontic treatment, restorations or cracks, and formed apex, was cleaned with periodontal curettes and disinfected with sodium hypochlorite 5% for 10 min. The crown was sectioned at the cement-enamel junction under cooling. The root (length: 16 mm) was endodontically treated with the step-back technique with stainless steel reamers (FGK, La Chaux-de-Fonds, Neuchâtel, Switzerland) until #50 and Gates-Glidden drills #1, #2 and #3 (Dentsply-Maillefer, Ballaigues, Vaud, Switzerland), using 2 ml of 5% sodium hypochlorite and 1 ml of 17% EDTA trisodium gel after the use of each instrument. The canal was then prepared with a #3 drill (Hi-Rem Prosthetic Post, Overfibers, Mordano, BO, Italy) to a 12 mm length, leaving the apical 4 mm unprepared.

The tooth was prepared for a full crown with a 1 mm-depth chamfer located 2 mm from the cervical margin to provide a ferrule effect. The root was molded with addition silicone (Elite HD+, Zhermack, Badia Polesine, RO, Italy) and 36 replicas of epoxy resin (Schaller 285, Model Center Schaller, Firenze, FI, Italy) mixed with glass microfibers (R & G, Waldenbuch, Baden-Württemberg, Germany) (30% by weight), with the same external and intracanal morphology to the original root were obtained.

Replicas were randomly divided into three groups (n=12) according to the post: FP-LM (fiber post with low elastic modulus), FP-HM (fiber post with high elastic modulus) and MP (metallic post). For FP-HM, conical-cylindrical posts (Hi-Rem Prosthetic Post, Overfibers, Mordano, BO, Italy) with elastic modulus 67 GPa were used. For FP-LM, fiber posts were exclusively fabricated for this investigation by the same manufacturer with the same shape as a Hi-Rem Prosthetic Post but with a lower elastic modulus (50 GPa). For MP, Co-Cr alloy (Heraenium PW, Heraeus Kulzer, Hanau, Hessen, Germany) posts (elastic modulus = 208 GPa) with the same shape as the aforementioned posts were cast. All posts had 0.9 mm diameter at the apical third, conicity of 0.08% and maximum diameter of 1.8 mm at the cervical third. Young’s modulus of the post materials was measured with three-point bending tests in accordance with ISO 3312⁹ and ISO 14125¹⁰.

The root canals were conditioned with 36% phosphoric acid (Detrey Conditioner 36, Dentsply, York, PA, USA) for 15 s and washed for 15 s. Excess water was removed with absorbent paper points. Adhesive (XP Bond, Dentsply, York, PA, USA) and activator (Self Cure Activator, Dentsply, York, PA, USA) were mixed in a 1:1 ratio for 2 s, applied into the canal using an applicator tip (Micro Brush Etch/Seal Blue 100, Dentsply, York, PA, USA) and left undisturbed for 20 s. Solvent was removed by air from a dental syringe for 5 s. Posts were cleaned with 70% ethanol, the adhesive mixture was applied onto the surface and left undisturbed for 5 s, and then air dried for 5 s. All posts had a length of 15.5 mm (3.5 mm coronal portion and 12 mm intracanal portion). Resin cement (Core X Flow, Dentsply, York, PA, USA) was inserted into the canal with the mixing tip, posts were positioned inside the canal, excess cement was removed and photoactivation was performed for 20 s. After cementation, all roots were embedded in resin epoxy cylinders (Technovit 4071, Heraeus Kulzer) up to 1.5 mm from the cervical margin.

Identical silver-palladium (Valcambi, Balerna, Ticino, Switzerland) crown frameworks were cast using the lost-wax technique. Cores were built up as follows: 1 – the coronal part of the root and post were etched and the adhesive mixture was applied in the same manner as for post cementation; 2 – each framework was internally lubricated with Vaseline; 3 – Core X Flow was inserted inside the frameworks and on the post, frameworks were positioned over the coronal portion of the roots and excess was removed with a microbrush; 4 – after 6 min, the frameworks were removed and the cores were photoactivated for 20 s; 5 – the frameworks were tried onto their respective cores, and when binding was encountered, the axial walls of the cores were adjusted so that every crown could reach the maximum seating. After core reconstruction, cores and frameworks were cleaned with 70% ethanol and the internal surface of frameworks was abraded with 50 μm aluminum oxide particles. Resin cement (Smartcem 2, Dentsply, York, PA, USA) was inserted inside the crowns with the mixing tip, crowns were settled in position over the casts and the cement excess was removed. Specimens were left undisturbed for 30 min.

Specimens were cleaned in a 37 °C ultrasonic bath for 15 min and then stored in 37°C water for 24 h. The fracture load test was executed in a universal testing machine (Instron 4465, Instron, Norwood, MA, USA) 24 h after cementation. Each specimen was positioned on a device at an angle of 45° in relation to the tooth long axis and a constant load at a crosshead speed of 0.5 mm/min was applied until failure (1000 N load cell). Specimens were examined under a stereomicroscope (Leica M-10, Wild Heerbrugg, Heerbrugg, Sankt Gallen, Switzerland) and failures were classified as shown in Figure 1A-D.

Figure 1
Schematic representation of the modes of failure. (A) DC: detachment between cervical root third and core; (B) DC/P: detachment between cervical root third and core with post pull-out; (C) CP: detachment between core and post; (D) F: fracture of the resin cylinder.

Graphics of the relation between the force applied (N) and the displacement (mm) until failure were registered for each specimen during the fracture load test. Displacement at 100 N load was recorded and compared among the groups.

RESULT

Normal distribution and homoscedasticity were verified with the Shapiro–Wilk and Levene’s test. Fracture load values were analyzed by one-way ANOVA. Displacement data were analyzed by one-way ANOVA and Tukey’s test. The significance level was 5%. Table 1 summarizes the fracture load means and standard deviations: post type did not affect the fracture load (p = 0.203). Failures were predominantly caused by detachment between cervical dentin and core with post pull-out (Table 1).

Table 1
Fracture load (N) means and standard deviations (SD), failure modes after the fracture load test and displacement

Group	Fracture load	Failure mode **				Displacement (mm) *
	Mean (SD)	DC	DC/P	CP	F	Mean (SD)
FP-LM	237.4 (65.11)A	3	8	1	-	0.81 (0.15)A
FP-HM	236.7 (92.85)A	4	4	4	-	0.46 (0.26)B
MP	295.8 (108.7)A	5	5	-	2	0.62 (0.07)B
		12 (33.33%)	17 (47.24%)	5 (13.88%)	2 (5.55%)

• ^*
  Different uppercase letters indicate a statistically significant difference (p < 0.05).
• ^**
  DC: Detachment crown; DC/P: Detachment crown/core/post assembly; CP: Detachment crown/core assembly; F: fracture of acrylic cylinder.

Displacement means and standard deviations at 100 N are presented in Table 1. The type of intraradicular post was statistically significant (p = 0.00): Tukey’s test showed that FP-LM displacement was significantly higher than that for FP-HM (p = 0.00) and MP (p = 0.04). Statistical power was calculated using a statistical software (Power of 0.93 for fracture load and 0.99 for displacement).

DISCUSSION

Since the elastic modulus of a post may influence the clinical performance of a restored tooth, the fracture load and displacement of roots restored using intraradicular posts with different elastic modulus were evaluated.

In this study we attempted to eliminate some of the variables which are inevitably present in in vitro studies evaluating the mechanical behavior of pulpless teeth. Human teeth, even within a certain range of acceptability, present inherent variations in size and morphology and may behave differently under mechanical loads due to chemical-physical differences, amorphous phase content and elastic modulus¹¹. The use of identical resin replicas constructed from only one dental element with the same external and intracanal morphology were used to standardize the roots dimensions and ensure specimens uniformity. In addition, although some studies have evaluated the influence of different intraradicular posts on the mechanical behavior of pulpless teeth, most of the post systems used did not present exactly the same form and diameter among the groups as the post characteristics were previously defined by the manufacturers^7,8, so the whole restorative technique was evaluated and not only the elastic modulus of the intraradicular post. In the current study all posts had the same shape and diameter so that the elastic modulus of the posts was the only factor evaluated.

No difference was observed between the three types of post in the fracture load test, thus the first research hypothesis was accepted. The absence of difference may be related to the ferrule effect provided for all specimens. The presence of a cervical ferrule positively affects the stress distribution pattern by reducing stress concentration on the root and risk of tooth fracture. Finite element analysis shows that the ferrule effect attenuates stress intensity on the root when either metal or fiber posts are used^12-15. Previous studies also did not find a difference in fracture resistance between teeth restored with crowns and cast and post cores or fiber posts when a ferrule was present^13,16,17. As long as there is ferrule presence, the effect of the stiffness of the post system is secondary for the mechanical behavior of endodontically treated teeth¹⁶, thus the difference between the elastic modulus of the post materials was minimized by the ferrule. Figure 2 shows a representation of the bending moments on the post. Fulcrum 1 is formed on the cervical level by 45° load and cervical surface of the root. Fulcrum 2 is formed at the ferrule level by 45° load and ferrule surface. As the distance between the loading point and the fulcrum 1 is higher than the distance between the loading point and fulcrum 2, the moment 1 (M1) is higher than the moment 2 (M2). So, in a tooth without ferrule the bending effect is higher on the crown/core/post assembly (Fulcrum 1) in comparison to a tooth with ferrule (Fulcrum 2). The ferrule effect protects the restorative assembly since the distance between the loading point and the support point of the crown/core/post assembly is reduced, minimizing the consequences of the bending moment at 45°. Since the bending moment is lower at the crown/core/post assembly in a tooth with a ferrule, the influence of the elastic modulus of the posts may be reduced. It is possible that in the absence of the ferrule effect MP could have had a statistically superior load since it presented a consistently higher fracture load (by approximately 25%) than the other groups, possibly because of its superior rigidity.

Figure 2
Schematic representation of the bending moments acting on the post. Red line: fulcrum 1. Green line: fulcrum 2. M: bending moment, which is measured by multiplying the applied force (F) with the distance between the load application point and the fulcrum line (d). M1: moment 1. M2: moment 2.

In the current study the predominant failure modes were cervical root third/core detachment and cervical root third/core detachment associated with decementation of the post. Loading at 45° to the palatal surface results in compressive stresses on the buccal surface and tensile stresses on the palatal surface¹⁸. These stresses are minimum in the center and maximum in the outer portions of the restorative assembly, so the higher tensile stress is concentrated in the outer cervical lingual portion^18,19 leading to adhesive failures between crown/core/post and cervical root third (DC failure mode). Besides tension and compression, loading at 45° also produces shear stress. It is maximum in the central area of the dental element, where the post is placed^18,19 and acts on the entire coronal interface (resin core/post) and intraradicular interface (post/cement/dentin), resulting in failure modes DC/P (adhesive failure between post and intraradicular resin) and CP (adhesive failure between core and post). Except for two cylinder fractures, all failures could be considered repairable, i.e. with possibility of re-intervention and preservation of the tooth⁴. These findings may also be associated with the presence of a ferrule, which has a protective effect since it improves the mechanical behavior of pulpless teeth by reducing cervical stress level on the restored root^14,16. Other studies have shown that the ferrule effect provided by remaining dentin is associated with restorable failure modes^20-22.

Displacement measurement associated with mechanical tests and failure mode analysis contributes to a better understanding of the behavior of the restorative complex during loading^13,16. Teeth are submitted to stress concentration and strain under load application. If the strain values exceed the resistance capacity, the restoration becomes structurally compromised, resulting in gaps at the adhesive interface, microleakage or cracks²³. In the present study, fiber posts with a low modulus of elasticity showed higher displacement than the other groups. When a system with components presenting different elastic modulus is loaded, the most rigid material resists greater loads without distortion²⁴. So, the observed findings may be explained by the fact that a less rigid material, i.e. FP-LM, is less resistant to deformation and consequently shows higher displacement.

The present study has limitations. Firstly, the elastic modulus of the replicas was approximately 5 GPa, which is lower than that of human dentin and thus does not exactly reproduce the clinical situation. Secondly, element finite analysis was not performed to determine the effect of the posts’ elastic modulus on stress distribution. Finally, no aging was performed. Monotonic tests do not perfectly simulate the dynamic conditions found in the oral environment; mechanical cycling could approximate the experiment to the clinical reality by inducing degradation of the restorative materials and adhesive interfaces due to mechanical and/or thermal solicitation. Although not statistically different, MP showed a higher fracture load than the other groups. If mechanical cycling had been performed, it is possible that a significant difference could be noted since repeated loads on the structure may propagate microscopic defects located in stress concentration areas, causing fracture due to fatigue at lower loads than under monotonic testing²⁵. Further research is necessary to investigate this aspect.

CONCLUSION

In the experimental conditions of this study it can be concluded that all the evaluated posts with different elastic modulus seem adequate for restoration of endodontically treated teeth regarding fracture loads. However, fiber posts with a high elastic modulus and metallic posts present lower displacement of the tooth-restoration assembly.

REFERENCES

• ¹
  Hegde J, Ramakrishna, Bashetty K, Srirekha, Lekha, Champa. An in vitro evaluation of fracture strength of endodontically treated teeth with simulated flared root canals restored with different post and core systems. J Conserv Dent. 2012 Jul;15(3):223-7. PMid:22876006. http://dx.doi.org/10.4103/0972-0707.97942
  » http://dx.doi.org/10.4103/0972-0707.97942
• ²
  Broch J, Marchionatti AM, Bergoli CD, Valandro LF, Kaizer OB. Fracture resistance of weakened roots restored with different intracanal retainers. Gen Dent. 2015 May-Jun;63(3):58-63. PMid:25945766.
• ³
  Faria AC, Rodrigues RC, Antunes RPA, Mattos GRF. Endodontically treater teeth: characteristics and considerations to restore them. J Prosthodont Res. 2011 Apr;55(2):69-74. PMid:20709618. http://dx.doi.org/10.1016/j.jpor.2010.07.003
  » http://dx.doi.org/10.1016/j.jpor.2010.07.003
• ⁴
  Zicari F, Van Meerbeek B, Scotti R, Naert I. Effect of ferrule and post placement on fracture resistance of endodontically treated teeth after fatigue loading. J Dent. 2013 Mar;41(3):207-15. PMid:23069329. http://dx.doi.org/10.1016/j.jdent.2012.10.004
  » http://dx.doi.org/10.1016/j.jdent.2012.10.004
• ⁵
  Ploumaki A, Bilkhair A, Tuna T, Stampf S, Strub JR. Success rates of prosthetic restorations on endodontically treated teeth; a systematic review after 6 years. J Oral Rehabil. 2013 Aug;40(8):618-30. PMid:23663088. http://dx.doi.org/10.1111/joor.12058
  » http://dx.doi.org/10.1111/joor.12058
• ⁶
  Veríssimo C, Simamoto Júnior PC, Soares CJ, Noritomi PY, Santos-Filho PC. Effect of the crown, post, and remaining coronal dentin on the biomechanical behavior of endodontically treated maxillary central incisors. J Prosthet Dent. 2014 Mar;111(3):234-46. PMid:24199605. http://dx.doi.org/10.1016/j.prosdent.2013.07.006
  » http://dx.doi.org/10.1016/j.prosdent.2013.07.006
• ⁷
  Sagsen B, Zortuk M, Ertas H, Er O, Demirbuga S, Arslan H. In vitro fracture resistance of endodontically treated roots filled with a bonded filling material or different types of posts. J Endod. 2013 Nov;39(11):1435-7. PMid:24139269. http://dx.doi.org/10.1016/j.joen.2013.05.006
  » http://dx.doi.org/10.1016/j.joen.2013.05.006
• ⁸
  Maroulakos G, Nagy WW, Kontogiorgos ED. Fracture resistance of compromised endodontically treated teeth restored with bonded post and cores: an in vitro study. J Prosthet Dent. 2015 Sep;114(3):390-7. PMid:26047799. http://dx.doi.org/10.1016/j.prosdent.2015.03.017
  » http://dx.doi.org/10.1016/j.prosdent.2015.03.017
• ⁹
  International Organization for Standardization – ISO. ISO 3312: sintered metal materials and hardmetals: determination of young modulus. Geneva: ISO; 1987.
• ¹⁰
  International Organization for Standardization – ISO. ISO 14125: fibre-reinforced plastic composites: determination of flexural properties. Geneva: ISO; 1998.
• ¹¹
  Panfilov P, Zaytsev D, Antonova OV, Alpatova V, Kiselnikova LP. The difference of structural state and deformation behavior between teenage and mature human dentin. Int J Biomater. 2016;2016:1-7. PMid:26989416. http://dx.doi.org/10.1155/2016/6073051
  » http://dx.doi.org/10.1155/2016/6073051
• ¹²
  Santos-Filho PC, Veríssimo C, Raposo LH, Noritomi MecEng PY, Marcondes Martins LR. Influence of ferrule, post system, and length on stress distribution of weakened root-filled teeth. J Endod. 2014 Nov;40(11):1874-8. PMid:25227215. http://dx.doi.org/10.1016/j.joen.2014.07.015
  » http://dx.doi.org/10.1016/j.joen.2014.07.015
• ¹³
  Santos-Filho PC, Veríssimo C, Soares PV, Saltarelo RC, Soares CJ, Marcondes Martins LR. Influence of ferrule, post system, and length on biomechanical behavior of endodontically treated anterior teeth. J Endod. 2014 Jan;40(1):119-23. PMid:24332002. http://dx.doi.org/10.1016/j.joen.2013.09.034
  » http://dx.doi.org/10.1016/j.joen.2013.09.034
• ¹⁴
  Upadhyaya V, Bhargava A, Parkash H, Chittaranjan B, Kumar V. A finite element study of teeth restored with post and core: effect of design, material, and ferrule. Dent Res J. 2016 May-Jun;13(3):233-8. PMid:27274343. http://dx.doi.org/10.4103/1735-3327.182182
  » http://dx.doi.org/10.4103/1735-3327.182182
• ¹⁵
  Watanabe MU, Anchieta RB, Rocha EP, Kina S, Almeida EO, Freitas AC Jr, et al. Influence of crown ferrule heights and dowel material selection on the mechanical behavior of root-filled teeth: a finite element analysis. J Prosthodont. 2012 Jun;21(4):304-11. PMid:22372913. http://dx.doi.org/10.1111/j.1532-849X.2011.00832.x
  » http://dx.doi.org/10.1111/j.1532-849X.2011.00832.x
• ¹⁶
  da Silva NR, Raposo LH, Versluis A, Fernandes-Neto AJ, Soares CJ. The effect of post, core, crown type, and ferrule presence on the biomechanical behavior of endodontically treated bovine anterior teeth. J Prosthet Dent. 2010 Nov;104(5):306-17. PMid:20970537. http://dx.doi.org/10.1016/S0022-3913(10)60146-1
  » http://dx.doi.org/10.1016/S0022-3913(10)60146-1
• ¹⁷
  Lima AF, Spazzin AO, Galafassi D, Correr-Sobrinho L, Carlini-Júnior B. Influence of ferrule preparation with or without glass fiber post on fracture resistance of endodontically treated teeth. J Appl Oral Sci. 2010 Jul-Aug;18(4):360-3. PMid:20835570. http://dx.doi.org/10.1590/S1678-77572010000400007
  » http://dx.doi.org/10.1590/S1678-77572010000400007
• ¹⁸
  Wandscher VF, Bergoli CD, Limberger IF, Ardenghi TM, Valandro LF. Preliminary results of the survival and fracture load of roots restored with intracanal posts: weakened vs nonweakened roots. Oper Dent. 2014 Sep-Oct;39(5):541-55. PMid:24502753. http://dx.doi.org/10.2341/12-465
  » http://dx.doi.org/10.2341/12-465
• ¹⁹
  Hibbeler RC. Mechanics of materials. São Paulo: Pearson/Prentice Hall; 2008.
• ²⁰
  Abdulrazzak SS, Sulaiman E, Atiya BK, Jamaludin M. Effect of ferrule height and glass fibre post length on fracture resistance and failure mode of endodontically treated teeth. Aust Endod J. 2014 Aug;40(2):81-6. PMid:24118334. http://dx.doi.org/10.1111/aej.12042
  » http://dx.doi.org/10.1111/aej.12042
• ²¹
  Aggarwal V, Singla M, Yadav S, Yadav H, Sharma V, Bhasin SS. The effect of ferrule presence and type of dowel on fracture resistance of endodontically treated teeth restored with metal-ceramic crowns. J Conserv Dent. 2014 Mar;17(2):183-7. PMid:24778519. http://dx.doi.org/10.4103/0972-0707.128053
  » http://dx.doi.org/10.4103/0972-0707.128053
• ²²
  Carlini B Jr, Cecchin D, Pereira GDS, Paulillo LA. Influence of remaining coronal structure and finish line on the fracture strength of roots restored with metallic posts. Braz Oral Res. 2011 Jul-Aug;25(4):345-50. PMid:21860923. http://dx.doi.org/10.1590/S1806-83242011000400011
  » http://dx.doi.org/10.1590/S1806-83242011000400011
• ²³
  Soares PV, Santos-Filho PC, Gomide HA, Araujo CA, Martins LR, Soares CJ. Influence of restorative technique on the biomechanical behavior of endodontically treated maxillary premolars. Part II: strain measurement and stress distribution. J Prosthet Dent. 2008 Feb;99(2):114-22. PMid:18262012. http://dx.doi.org/10.1016/S0022-3913(08)60027-X
  » http://dx.doi.org/10.1016/S0022-3913(08)60027-X
• ²⁴
  Bijelic J, Garoushi S, Vallittu PK, Lassila LV. Fracture load of tooth restored with fiber post and experimental short fiber composite. Open Dent J. 2011 Mar;5(1):58-65. PMid:21566716. http://dx.doi.org/10.2174/1874210601105010058
  » http://dx.doi.org/10.2174/1874210601105010058
• ²⁵
  Zamboni SC, Baldissara P, Pelogia F, Bottino MA, Scotti R, Valandro LF. Fatigue resistance of bovine teeth restored with resin-bonded fiber posts: effect of post surface conditioning. Gen Dent. 2008 Jan-Feb;56(1):56-9. PMid:18254561.

Publication Dates

• Publication in this collection
  Aug 2017

History

• Received
  19 Feb 2017
• Accepted
  12 July 2017