Improvement of Circularly Polarized Slot-Patch Antenna Parameters by Using Electromagnetic Band Gap Structures

This paper is devoted to the design of a novel Electromagnetic Band Gap (EBG) circularly polarized slot-patch antenna in multilayered configuration. The operating frequency band can be controlled via the disk radius and adjusting the slit lengths. An arrangement combining the circular slot-patch antenna design and feeding sources included are considered is necessary. Due to the exisiting of two feeding points, Position of both feeding points will permit Right-hand and Left-hand circular polarization operations. Thickness of substrate is chosen to reduce the spurious surface wave and width. The same technique will be used for the EBG cirlcularly polarized circular slot-patch antenna network and carry two benefits (such as improvement of bandwidth, beamforming, creating zero radiation beams) and filtering characteristics of the resonator (spatial filtering, increased directivity, misalignment) due to the resonant structure itself. The analysis provided will confirm successfully the various proposed structures and interest occupied by these types of antenna. Two approaches, one introduced by one layered Circularly-Polarized Patch-Slot antenna design with some changes in material configuration and the other produced by multilayered structures with different dielectric constants in the EBG resonator, are simultaneously used as key controllers of directivity enhancement.


I. INTRODUCTION
In many telecommunication applications, particularly for the radio-relay, systems must radiate in circular polarization.These systems must present the same characteristics as an antenna with linear polarization (high gain, simplicity of realization, etc.).To fulfill these conditions, patch array antennas [1], reflector antennas, or horns are commonly used.A new concept of directive electromagnetic band gap (EBG) antenna will be analyzed [2], [3].Hence, the electromagnetic band gap structures are defined as artificial periodic (or sometimes non-periodic) objects, of 429 Brazilian Microwave and Optoelectronics Society-SBMO received 05 Sept 2016; for review 08 Sept 2016; accepted 18 Oct 2016  Brazilian Society of Electromagnetism-SBMag © 2016 SBMO/SBMag ISSN 2179-1074 dielectric materials and metallic conductors [4], that prevent/assist the propagation of electromagnetic waves in a specified band of frequency for all incident angles and all polarization states.They offer pass-band and stop-band (band-gap) to electromagnetic waves in the same way as the semiconductor do in electronics.Another important characteristic of these materials is the ability to open localized electromagnetic modes inside the forbidden frequency band-gap by introducing defects in to the periodic structures [4].EBG structures have been used in several applications, such as Directive antennas [5], harmonic control [6].
Using these kind of EBG structures, more attractive features are offered such as low profile, light weight, easy fabrication, integrability with microwave and millimeter-wave integrated circuits, and conformability to curved surfaces [1].Such a design can avoid the use of multiple antennas, like for instance, by integrating receiving and transmitting functions in to the same communication system.
The dual frequency operation is achieved when the slots perturb the fundamental resonant frequency of the patch exciting a new resonance mode.The resonance frequency of the new mode can be either orthogonal polarization [4] or lower [4,5] or higher [6] than the original dominant mode with either the same [7] and is strongly dependent on the slot dimensions.The electromagnetic band gap (EBG) structures are defined as artificial periodic (or sometimes nonperiodic) objects that prevent/assist the propagation of electromagnetic waves in a specified band of frequency for all incident angles and all polarization states.
With Four Inserted Slits in the multilayered Circular patch-slot EBG antenna as the fundamental structure (Figure 1) and with dual-sources [9].The patch-size reduction is achieved by cutting four equally spaced slits at the boundary of the circular patch.The role of multilayered configuration is proved by presenting their impact on the radiation, gain & bandwidth.This kind of multilayered Circularly Polarized Slot-Patch EBG antenna is found useful for wireless communication systems as it presents the desired performances.Improvement of bandwidth and gain and multiple operating frequencies needed for different devices can be achieved by modification of physical parameters such as radius, thickness and type of dielectric substrate.Comparison of performance of proposed design with conventional patch-slot circular antenna having identical patch radius and with same slits has also been reported and compared to analytic methods for better understanding.
The principle of the EBG resonator antennas is described in the first part of this work.The principle of circular polarization is shown.Simulation and analytic results at 9.1 GHz are presented.
Fig. 1.Geometry of a circularly-polarized circular microstrip antenna with four inserted slits.

II. EBG PATCH-SLOT CIRCULAR ANTENNA DESIGN
The substrate material plays a significant role in the design and simulation of microstrip patch antenna.The material selection depends upon permittivity, conductivity, thermal expansion and cost.In this work, the substrate material with dielectric constant of 4.4 and dielectric loss tangent of 0.009 [10][11][12][13].
The electromagnetic band gap (EBG) structures defined previously as artificial periodic (or sometimes non-periodic) objects will prevent/assist the propagation of electromagnetic waves in a specified band of frequency for all incident angles and all polarization states.Another important characteristic of these materials is the ability to open localized electromagnetic modes inside the forbidden frequency band-gap by introducing defects in to the periodic structures [10].They have been used in several applications, such as Directive antennas [11], harmonic control [12].Here, a novel design of single & multilayered patch-slot circular microstrip EBG antenna having displacement of the coaxial feeding source from the center of the circular patch is proposed and its simulated radiation performances in free space conditions have been presented.The impact of the permittivity is presented.

A. Circularly Polarized Patch-Slot Antenna Design
Next  Table 1 shows Return Loss, VSWR and 2-D Gain for the designed circular patch-slot antenna with substrate thickness from 1mm to 2mm in the steps of 0. 2mm.A comparative analysis is made for the obtained results.Table 2 shows the antenna additional parameters with respect to the change in the thickness of the substrate.The far-zone electric field lies in the E-plane and far-zone magnetic field lies in the Hplane.The patterns in these planes are referred to as the E and H plane patterns respectively.
These parameters concern the radiation power, total efficiency and Return losses (dB) In all next design and analysis, we fix the thickness of the substrate h=1.6mm The summary of the comparison study is detailed in the next table shown below.Hence, we have optimized the length of slots and their impact on the resonance frequencies and bandwidths.From the simulated structure and based on modification of different geometric parameters, the frequency ratio can be controlled.

B. Patch-Slot Circular Single Antenna Using EBG Structures with Magnetic Lateral Walls
The circular patch-slot geometry discussed above has been modified by the insertion of new EBG materials and see the influence of the number of layers on the performance of the antenna while keeping the same dimensions as before concerning the patch and lateral conditions walls.The distance between the patch and the first dielectric layer is λ 0 / 2 = 16.5 mm and the layer thickness is λ g / 4 =9.62mm.
Note that in this section, the dielectric permittivity of the different included layers is fixed ε r = 4.4 and only the number of layers varies.
For only a 2-layred EBG antenna, the return loss is about -54dB     Here, we must add to our patch new EBG materials and see the impact of the number of layers on the performance of the antenna while keeping the same dimensions as before the patch and conditions power side (thickness of the substrate h=1.6mm,ε r =3.6, Slot width=4mm and Length (L x =10, L y =5 mm), Radius of patch R=32 mm).The distance between the patch and the first dielectric layer is λ 0 / 2 = 16.5 mm and the layer thickness is λ g / 4 = 9.62mm.
The summary of the comparison study is detailed in the next table shown below.As the number of layers' increases, the gain increases against the opening angle decreases so the antenna is more directive.Note that the directivity and bandwidth increase with the number of EBG layers.

III. CIRCULARLY POLARIZED MULTILAYERED SLOT-PATCH EBG ANTENNA IN PERIODIC CONFIGURATION
The objective in this section is the design of an infinite Circular EBG slot-patch antenna array.
Since the conventional technology presents some limitations such as those in coupling between elements, stability, complexity, the New Multilayered EBG Slot-patch antenna array has the aim to rectify some of these limitations.It is designed to cover high directivity, covering navigation systems, and be substitute for conventional technology antennas.It has been applied with the main challenge here complying with all the specifications given by Wide Area Augmentation System (WAAS).High directivity, stable Axial Ratio and phase center were the most critical parameters.
Several EBG technologies have been designed [14,15].In our case, it is fundamental to analyze a prototype of single circular EBG Slot-patch antenna with periodic lateral walls.Hence, we can obtain an optimization for the infinite array.At the same time antenna dimensions are significantly reduced by the use of high dielectric EBG constant substrates while maintaining high efficiency values.Some precautions regarding the sources placement and coupling should be taken.order to plan the design of real multilayered circular EBG slot-patch antenna array.As shows in the next table, by increasing the number of layers, we find decrease in stability since some ripples appear in case of S 11 while maintaining the two modes of circular polarizations.The change in number of layers of material shows the ability to increase gain and make more directive antenna according to the preferred propagation direction.But, it does not directly affect the bandwidth.By increasing the number of layers, we decrease stability (presence of ripples in S11).The change in number of layers of material shows the ability to increase gain and make more directive antenna according to the preferred propagation direction.This does not directly affect the bandwidth.In this case, searching infinite array, while maintaining mutual interference between patches is worthy obtained with improvement of performance in comparaison with classic arrays figure shows the geometry of a compact circularly polarized circular microstrip antenna.The circular patch has a radius D, and four narrow slits equally spaced and inserted at the boundary of the circular patch lower the resonant frequency of the dominant TM11 mode.The design considerations for the proposed patch-slot circular antenna as shown in Figure1 on RT-Duroid 431 Brazilian Microwave and Optoelectronics Society-SBMO received 05 Sept 2016; for review 08 Sept 2016; accepted 18 Oct 2016 Brazilian Society of Electromagnetism-SBMag © 2016 SBMO/SBMag ISSN 2179-1074 substrate material with a relative dielectric constant of 4.4 with thickness of 1.6 mm.The diameter of the circular patch is 3.2cm.Length of the slots (l x , l y ) are varying from (10,5) to (25,24,5), Width of the slot= 0.05 cm, Radius of the feed element=0.025cm.Two Coaxial feedings are used to ensure the circular polarization.Hence, When the ratio of the total slit length in the slot in xdirection (Lx) to that in the y-direction (Ly) is properly chosen, the two near-degenerate modes can be excited, using a single feed along the diameter at φ=45 0 planes, to be of equal amplitudes and 90 0 phase difference, which results in a CP radiation.When Lx is greater than Ly, the feed position at point A is for right-hand CP operation, while point B is for left-hand CP operation.The two slits on the x axis have the same length L x , and the two slits on the y axis have an equal length L y .and insure that L x > L y Then, by varying x (0 < x < y).

Fig. 6 .
Fig. 6.Polar radiation pattern of an the circularly-polarized Slot-Patch EBG antenna within a Plexiglas layer plane E It is then necessary to check parameter levels all along the antenna operating band: A high coupling level can perturb the global functioning of the antenna array.In our case, this kind of circular multilayered EBG slot-patch antenna with periodic lateral walls is designed and the multilayered technology is checked to give us an idea on the entire attitude of the periodic circular planar EBG slot-patch antenna network.Here, we Keep the same geometric parameters as the previous analysis.Hence, we introduce new change concerning the lateral walls in order to could analyze a whole network composed by infinite patches.That periodic lateral walls condition is very important in

Fig. 7 .
Fig. 7. 3D radiation pattern of a 2-Layered Circularly Polarized Slot-Patch EBG antenna with periodic walls Circularly-Polarized Slot-Patch and circularly Ploarized Solt-Patch EBG antenna was done by insertion of new EBG substrates in the aim to perform the electromagnetic characteristics (Gain, Bandwidth, radiation efficiency…) and changing the substrate thickness.Antenna parameters are ddeply changing in function of number of EBG substrates.From obtained results, the ideal number of EBG substrates is limited to two layers considering the different output parameters (Gain, bandwidth, directivity…).Either, the gain is increasing first and then decreased when thickness increases from 1.2mm to 1.8mm for the Circularly-Polarized slot-patch EBG antenna.The same behavior is observed for the case of radiation efficiency, peak gain and peak directivity.Overall we observed that the stability in the performance characteristics for Circularly-Polarized slot-patch EBG antenna is showing superior results compared to the circularly-Ploarized Slot-Patch antenna.Especially in case of infinite array and the introduction of the periodicity factor.

Table 2 .
Additional Antenna Parameters of the Circular Slot-Pacth Antenna

Table 3 .
Impact of the geometric parameters of the slot (Length and width) on the Antenna Parameters of Circularly

Table 4 .
Impact of The Number of Layer with ɛ r = 4.4 Fixed On the Antenna Parameters

Table 5 .
impact of number of dielectric layers on the EBG antenna network