Concept of a Maneuvering Load Control System and Effect on the Fatigue Life Extension

This paper presents a methodology for the conceptual design of a Maneuver Load Control system taking into account the airframe flexibility. The system, when switched on, is able to minimize the bending moment augmentation at a wing station near the wing root during an unsteady longitudinal maneuver. The reduction of the incremental wing bending moment due to maneuvers can lead to benefits such as improved pay-loads/gross weight capabilities and/or extended structural fatigue life. The maneuver is performed by following a desired vertical load factor law with elevators deflections, starting from the trim equilibrium in level flight. The system observes load factor and structural bending through accelerometers and calibrated strain sensors and then sends signals to a computer that symmetrically actuates ailerons for reducing the structural bending and elevators for compensating the perturbation to the longitudinal equilibrium. The major limit of this kind of systems appears when it has to be installed on commercial transport aircraft for reduced OEW or augmented wing aspect-ratio. In this case extensive RAMS analyses and high redundancy of the MLC related sub-systems are required by the Certification Authority. Otherwise the structural design must be performed at system off. Thus the unique actual benefit to be gained from the adoption of a MLC system on a commercial transport is the fatigue life extension. An application to a business aircraft responding to the EASA Certification Specifications, Part 25, has been performed. The aircraft used for the numerical application is considered only as a test casestudy. Most of design and analysis considerations are applicable also to other aircraft, such as unmanned or military ones, although some design requirements can be clearly different. The estimation of the fatigue life extension of a structural joint (wing lower skinstringer), located close to the wing root, has been estimated by showing the expected benefit to be gained from the adoption of such a maneuvering load control system.


INTRODUCTION
Several aircraft manufacturers have been conducting for many years research in the area of active controls, that are becoming increasingly important in the design of modern aircraft.Nowadays active control systems drive the constructing architecture and the configuration of the whole aircraft by affecting operative mission feasibility and flight performances.Thus the adoption of active control systems plays an essential role since the early stages of design.The choice to equip an airplane with active controls modifies the design philosophy approach also from a certification viewpoint.The vehicle must be able to take on board a set of equipment such as 1.Sensors aimed at measuring what has to be observed or controlled; 2. On-board computers; 3. Fly-By-Wire (FBW) controls; 4. Electro-mechanic and/or electro-hydraulic actuators; 5. Classic or advanced aerodynamic controls (control surfaces, control jets, etc.).
All these kinds of equipment together with their on-board integration systems are nowadays subjects of research and development in order to optimize the automatic control efficiency and reliability.Active controls must have a level of safety equivalent to that of conventional design.In this context an automatic system aimed at reducing structural loads can be conceived.This kind of system is generally called Load Alleviation System (LAS) and involves systems for gust and/or maneuver load control.These load alleviation systems are mainly aimed at gust-alleviation for improved ride comfort.The alleviation is accomplished by means of an active wing bending damping, which alleviates structural fatigue loads on the one hand, and lowers pitch attitude variation and vertical accelerations in the cabin on the other (Hahn (1992), Merat (2008), Wildschek (2009)).A recent survey (Hecker and Hahn (2007)) showed that a Gust Load Alleviation System (GLAS) directed towards the reduction of vertical accelerations due to turbulence can yield to an undesired overcompensation of structural loads, which can be avoided only by appealing on an optimized tuning of the GLAS.The present work is focused on a different objective that can be achieved with a Load Alleviation system, i.e. to obtain a reduction in internal wing loads for enhanced performance (such as an aerodynamic efficiency increase due to a wing Aspect-Ratio augmentation or higher maneuver limit load factors for high performance aircraft), structural fatigue life extension, Operative Empty Weight (OEW) reduction.Aircraft Wing Structure is generally maneuver-load or gust-load critical depending on whether the airplane is a high-performance (such as a fighter or a military unmanned air vehicle) or a commercial transport.In the case of a high performance aircraft the improving of ride comfort is not a concern, whereas a method aimed at reducing directly internal structural loads due to maneuvers can be of great significance.In other words, since the wing weight is essentially function of the bending moment acting near the wing root, an effective load alleviation system must be able to reduce the bending through a redistribution of the aerodynamic load during a maneuver.The whole process becomes relevant for high performance aircraft if the alleviated maneuver is performed at the same vertical load factor as that attained in case of LAS switched off.Structural weight reduction Latin American Journal of Solids and Structures 13 (2016) 2298-2315 (part of the Operative Empty Weight, OEW) obtained with such a Load Alleviation System allows more payload and/or fuel to be carried since the Max Take-Off Weight (MTOW) does not vary.On the other hand, by keeping the MTOW and the OEW constant, the LAS allows obtaining higher maneuver load factors with the same values of maximum wing bending, thus leading to better maneuver performance.Nevertheless the weight reduction is not the unique benefit to be gained from the adoption of a LAS.This system can allow increasing the wing span length and, at the same time, keeping the same structural weight.The resulting higher wing aspect ratio (and thus less induced drag) leads to a reduction in fuel consumption for the benefit of greater payloads or more fuel for increased wing internal volume.In both cases, the resulting autonomy increase is attracting for commercial transports.The driving idea of this survey is to control maneuvering loads by means of a symmetrical actuation of the ailerons or other dedicated control surfaces located close to the wing tip in order to rearrange the aerodynamic loads.This way to proceed is not new, but the purpose of this work is to offer a methodology to perform the conceptual design of a Maneuver Load Control system taking into account the airframe flexibility.The system, when switched on, is able to minimize the bending moment augmentation in a wing station near the wing root during an unsteady maneuver.The maneuver is performed by following a desired vertical load factor law by deflecting elevators, starting from the trim equilibrium in level flight.The system observes load factor and structural bending through accelerometers and calibrated strain sensors and sends signals to a computer that symmetrically actuates ailerons (for reducing the structural bending) and elevators (for compensating the perturbation to the longitudinal equilibrium).All numerical analyses aimed at simulating the aircraft behavior during maneuver with MLC-on or MLC-off are performed both with and without the contribution due to the flexibility of the aircraft.Indeed the whole study is addressed to show the importance of considering the effect of aeroelasticity during the conceptual design of such a MLC system, resulting in much more reliable information about the quality of flight mechanics and the design of other subsystems such as servos or control surfaces.As highlighted previously, the reduction in structural internal wing loads due to the adoption of a MLC system can be motivated by the requirement of reaching enhanced performance (aerodynamic efficiency growth due to a wing Aspect-Ratio augmentation or higher maneuver limit load factors for high performance aircraft), OEW reduction, or structural fatigue life extension.The major limit of this kind of systems appears when it has to be installed on commercial transport aircraft for reduced OEW or augmented wing aspect-ratio.In this case extensive RAMS analyses and high redundancy of the MLC related subsystems are required by the Certification Authority.Otherwise the structural design must be performed at system off.Thus the unique actual benefit to be gained from the adoption of a MLC system on a commercial transport is the fatigue life extension.For this purpose, the second part of this paper is focused on the estimation of the fatigue life extension of a structural joint (wing lower skin-stringer) located close to the wing root.Analyses are carried-out by following the state-of-the-art method presented in ESDU 79024 (1979), ESDU 69023 (1989) and ESDU 75008 (1984).The application is performed for a business jet responding to the Part 25 of the EASA Certification Specification, for two kinds of mission: short and long range.Structures 13 (2016) 2298-2315 2 MANEUVER LOADS CONTROLLING STRATEGY Several Feedback Control Systems (FCS) are currently installed on civilian and military aircraft.Some of them are aimed at increasing the airplane stability and others at controlling flight parameters (such as autopilot systems).The most used types of FCSs to alleviate inherent stability problems or to control flight parameters are:

Latin American Journal of Solids and
 Angle of Attack Feedback to the longitudinal controls (elevators or canards);  Load factor feedback to the longitudinal controls (elevators or canards);  Angle of sideslip feedback to the directional controls (rudders).
The LAS object of this work is aimed at obtaining wing bending reduction at a specific Wing Control Station (WCS) usually near the wing root, but by attaining always the same design vertical load factor.To accomplish this objective, the LAS incorporates a Load Factor Feedback (LFF) to the elevators in order to perform a longitudinal maneuver by automatically following the desired load factor time history.The MLC is accomplished by observing the bending at the wing root station and acting on the load alleviators (dedicated control surfaces rather than ailerons and/or flaps) in order to shift the wing center of pressure inboard.The structural load reduction can be carried-out in two alternative ways: 1.By activating the MLC when the bending reaches a specified absolute value (less than the limit design value with MLC-off); 2. By using a reference signal identically zero for the incremental bending so that the MLC immediately acts when the acting load exceeds the reference 1-g bending.Such reference is not a unique value, it is represented by a range of values, to be calculated for a combination of different flight conditions (Mach number versus altitude for each mass condition).
The main practical issue is related to the bending moment observation.This can be accomplished by means of strain gages measurements, as illustrated in literature (Aiken (1948), Rauscher (1984), Di Palma (2007)).Experimental ground calibrations are needed in order to correlate all strain gage signals to the bending moment acting on the wing control station (Skopinski (1953), Jenkins (2007) and Lokos (2002 and 2004).The load factor is kept compliant with the desired reference signal whether or not the MLC is switched on or off since the load factor perturbation is controlled and minimized by the action of the LFF.On the other hand the LFF acts on the longitudi-

LAS MLC LFF
Latin American Journal of Solids and Structures 13 (2016) 2298-2315 nal control by deflecting elevators and thus by varying angle of attack and other flight parameters that affect the wing root bending.

AEROELASTIC THEORETICAL MODEL
Longitudinal and unsteady maneuvers are developed by using the methodology presented by Paletta et al. (2010), taking into account the airframe flexibility by means of a modal approach, typical of the Dynamic Aeroelasticity domain.Normal Modes are used extensively in the dynamic analyses of airplane responses, including investigations into aeroelastic instabilities such as flutter.This approach allows the solution of a generic structural static problem without fixing a suitable number of constraints: the airplane can be considered unrestrained.

A Sub-Section
The theoretical model is based on the general equation of the dynamic Aeroelasticity in a modal approach, for a symmetric maneuver (Eq.(1), a system of N+2 differential equations of motion, where N is the number of elastic modes).
where single and double underlines denote respectively vectors and tensors.Eq. ( 1) is written by distinguishing rigid and elastic modes through subscripts R and E. The components of q are the degrees of freedom of the airplane: the plunge and the pitch mode.Q is the quasi-steady generalized aerodynamic forces matrix, ρ is the air density, V is the aircraft velocity, m is the generalized mass matrix, ϭ is the damping coefficient matrix, K is the generalized stiffness matrix, j is the imaginary part of quantity, ω is the circular frequency, and δ is the elevator deflection.
Eq. ( 1) can be written in the time domain and by making some positions and substitutions (like in Paletta et al. (2010)) becomes: In which, all matrix are used to obtain elastic generalized coordinates starting from rigid generalized coordinates.Eq.( 2), together with Eq. ( 3) are the main equations in the symmetric quasi-steady aeroelasticity, from which the evolution of a symmetric maneuver during time can be evaluated.The equations above are written for a single control surface (i.e. the elevator for an unalleviated maneuver), but it Latin American Journal of Solids and Structures 13 (2016) 2298-2315 is possible to write the same equations by involving two or more controls (i.e. the elevator and the load alleviator for an alleviated maneuver), by simply changing some formal notations.

Open-Loop State-Space Model
The airplane, in level flight, is modeled by means of a state-space system aimed at simulating unsteady longitudinal maneuvers.Since the objective of the work is to control load factor and bending by feeding-back the system to elevators and ailerons, the state-space representation is chosen because of its straight forward implementation with commercial tools such as Matlab and Simulink ® .By introducing the load alleviator control (i.e. a symmetrical deflection of ailerons), Eq. ( 3)) becomes: here C F and CC F contain respectively the force coefficients for elevator and aileron controls, β is the load alleviation control surface deflection.By choosing the state as and the input as Eq. ( 4) can be written in the controllable canonical form and The output vector contains Shear (S), Bending (B) and Torsion (T) at the Wing Control Station (WCS), vertical load factor (nz), pitch acceleration (  q ) and aileron hinge moment ( Where α is the angle of attack and h is plunge angle.By taking the following positions: the output equation is written as follows: Latin American Journal of Solids and Structures 13 (2016) 2298-2315 and Eqs. ( 7)-( 9) together with Eqs. ( 15)-( 17) represent the Multi Input -Multi Output (MIMO) state-space system of the airplane in longitudinal flight.
It results and that is the system has full state controllability whereas it is not completely observable (in its first state).

MLC SYSTEM: APPLICATION TO A CS-25 BUSINESS JET
The aircraft used for the numerical application is a business jet responding to the EASA Certification Specifications Part 25.The aircraft top view is shown in Figure 2. The maximum vertical load factor is 2.5, whereas the chosen WCS is at the wing root.The aeroelastic model is made up of an aerodynamic model for Doublet Lattice Method (DLM) calculations, a dynamic model and a matching model (see Figure 3).The dynamic model is of stick-beam type for wing, fuselage and tail-planes while the junctions are modeled by means of direct matrix input simulating stiffness and inertia behaviour (Nastran DMIG matrices).Winglets and nacelles are considered rigid.The inertia is modelled by a set of concentrated masses with their own moments of inertia.The matching modellink between aerodynamics and structure -is made up of a set of grids (Interface Grids) for load and displacement interpolations.Some different combinations of speed and altitude are chosen as flight conditions to be analyzed.Four of these are at the same Calibrated Airspeed (CAS) but with different altitude from sea level to about 30 kft.The other ones are chosen to carry-out sensitivities versus the Mach number and the dynamic pressure.Every flight condition is analyzed for three different mass configurations, i.e. for empty fuel tank (MZFW), full fuel tank (MTOW) and an intermediate condition (50% fuel).All calculations have been performed for rigid and elastic aircraft, i.e. for the evaluation of both

Feedback Control System Architecture
The FCS architecture is shown by the SIMULINK ® schematic of Figure 4.The whole system is made up of two feedback SISO systems, simulating the Load Factor Feedback and the MLC system.The light blue block represents the aircraft dynamics in longitudinal flight (plant) and magenta blocks simulate the servo dynamics.The transfer function adopted to model both servos is the following: 7.994e004 -------------------------s^2 + 282.7 s + 7.994e004 which means a natural frequency of 45 Hz and a damping ratio of 0.5.Cyan blocks are the inputs for the system.The "MLC switch" is used to activate the MLC system.Once a load factor time history is established, only minimum and maximum WCS Bending moments have to be imposed.This is done by putting these values in the "Bending Saturation" block in order to give an allowable load range.
Grey blocks simulate saturations due to mechanical stops and maximum allowable deflection rates.Being the MLC using ailerons as load alleviators, it has to be in series with the roll control system in order to preserve lateral manoeuvrability, thus symmetric MLC deflections are additive to the anti-symmetric roll deflections until the mechanical control surface stops are reached.The MLC servo authority limits are established as 15 degrees trailing edge up and down.The maximum allowable deflection rate is chosen as ±30 degrees per second.Orange blocks are the outputs of the system.Although the linear system is built with only six outputs, other flight parameters are evaluated by external integrations, derivations and/or multiplications.

LFF and MLC Controllers: Requirements and Synthesis
Three types of system performance specifications (requirements) have been considered (Roskam (2009) As regards the frequency domain specifications, a gain margin of a factor of 2 and a phase margins larger than 35 degrees are fixed.System time domain specifications are given in terms of the response of the system to a unit step input: Overshoot (5% of the steady-state output for Margin of Safety Policy reasons), Rise Time (a performance requirement, 0.25 s for the LFF system and 0.10 s for the MLC system) and Settling Time (1.0 sec.to reach and remain within a 2 percent of its final value) are the adopted time domain specifications.The last specification regards the Position Error ( ) e ¥ requirement.Considering a negative feedback system subject to a unit step input, the Position Error is the difference between the unity and the steady-state response (C(s) for s  ¥ ).For the present application, the Position Error related to the LFF system has to be zero.

LFF Controller Synthesis
In order to fulfill all the requirements, the load factor is fed-back to the elevator deflection by using a negative feedback with a PID (Proportional Integral Derivative) controller.The controller synthesis is done by applying the tuning method presented Skogestad (2004) and implemented in Matlab ® through the SISOTOOL ® graphic user interface.The PID controller of the LFF system is designed (by tuning all constants KP, Ti, Td) for each flight case by taking into account the flexibility of the aircraft.The same controller is adopted also in the case of rigid aircraft by simply reducing the proportional constant KP according to the stability requirements presented so far.For conciseness reasons all the diagrams showing the dependencies of PID parameters upon dynamic pressure, Mach number and mass condition are not reported.About the dependency upon the dynamic pressure, KP decreases when the dynamic pressure increases in a quite linear manner.The most evident result is the dependency of KP for rigid aircraft much less marked if compared with KP for elastic aircraft.The dependency upon the Mach number is analogous for both rigid and elastic aircraft: KP increases when Mach number increases.The trend results quite quadratic.Any appreciable differences in the dependency of PID parameters upon mass conditions between rigid and elastic aircraft are registered.

MLC Controller Synthesis
The Bending moment is fed-back to the aileron deflection by a negative feedback with a logical "if", a saturation block and a simple Proportional controller.The P controller of the MLC system is Latin American Journal of Solids and Structures 13 (2016) 2298-2315 designed for each flight case for both rigid and elastic aircraft by simply tuning the proportional constant KP in order to fulfill all the specifications presented so far.As done for the LFF controller, the gain of the MLC P controller has to be continuously varied in flight in order to keep the specifications fulfilled.Also in this case it could be done by an inboard computer interpolating the calculated data at each flight condition.For sake of conciseness all the diagrams showing the dependencies of the controller gain upon dynamic pressure, Mach number and mass condition are not reported.It results that the dependency of the gain P upon the dynamic pressure has a quite linear behaviour with a negative trend; in the case of rigid aircraft it is slightly more marked if compared with the case of elastic aircraft.This happens because the loss of ailerons effectiveness due to flexibility partially alleviates the stronger aerodynamics associated with an increasing dynamic pressure.The dependency upon the Mach number is similar, but the difference between rigid and elastic aircraft is more evident.

Performance of the Maneuver Load Control system -The Effect of Aeroelasticity
In this section an unsteady maneuver similar to a checked maneuver is presented.The performance of the Maneuver Load Control system is measured by the Alleviation Factor (AF) parameter (Eq.( 20)).It specifies the percentage of the maneuver incremental load reduction in a specific control section.Since the load characteristic to be alleviated is the bending moment (B), AF is calculated as follows: As shown in Figure 5, for elastic and rigid aircraft, the LFF system succeeds in following the desired load factor also when MLC is switched on, despite the symmetric aileron deflection helps the elevator in pitching up the airplane and thus in reaching the load factor peak earlier.Figure 6 shows the control surface deflection time histories, for elastic and rigid aircraft, for both MLC-on and off.Notice that the necessary load alleviator deflection in the case of flexible aircraft is greater than in the case of rigid aircraft.This is due to the loss of effectiveness of the outboard ailerons used as load alleviators.The same reason also drives the increase of the necessary servo power to actuate the load alleviators (see Figure 8).The calculated necessary extra power for elastic aircraft is about 60% higher than that calculated for rigid aircraft.Although the aileron hinge moment with rigid aircraft is slightly higher than that calculated for elastic aircraft (see Figure 7), in this latter case the MLC actuation is much more fast, thus leading to a higher deflection angular velocity and a higher necessary servo power.The dependencies of AF upon M, q and aircraft weight (fuel) are depicted in Figure 9 to Figure 11 for both rigid and elastic aircraft.At fixed Mach number, greater the dynamic pressure, more effective the LAS (Figure 5).The gap between rigid and elastic aircraft increases with the dynamic pressure.The LAS effectiveness augmentation with Mach number is less marked than with the dynamic pressure (Figure 6).case of elastic aircraft, such a dependency becomes smoother.Figure 7 shows the dependency of AF upon mass conditions: the trend appears quite linear.This behaviour repeats at different flight conditions (i.e.different Mach number and dynamic pressures).The analysis performed underlines that percent errors are relatively low so that this model can be considered sufficiently reliable to characterize the performance of the MLC system for a wide range of flight conditions in a conceptual design phase.

FATIGUE LIFE EXTENSION DUE TO A MLC SYSTEM
As often highlighted in the previous sections, the reduction in structural internal wing loads due to the adoption of a MLC system can be motivated by the requirement of reaching enhanced performance.The major limit of this kind of systems appears when it has to be installed on commercial transport aircraft for reduced OEW or augmented wing aspect-ratio.In this case extensive RAMS  analyses and high redundancy of the MLC related sub-systems are required by the Certification Authority.Otherwise the structural design must be performed at system off.Thus the unique actual benefit to be gained from the adoption of a MLC system on a commercial transport is the fatigue life extension.The present section is focused on the estimation of the fatigue life extension of a structural joint (wing lower skin-stringer) located close to the wing root.

Analysis Strategy
Analyses are carried-out for both cases of MLC-on and MLC-off in order to appreciate the benefit of having an MLC system in terms of structural fatigue life improvement.Hypotheses of this work are: 1.When MLC is switched on, the airplane is in level flight with a wing root bending alleviation of 10% (AF=0.1); 2. If a gust front is going to be encountered, the MLC is switched-off and load alleviators (control surfaces) are blocked to the last position for keeping the static load alleviation constant during the turbulence;

Determination of Cumulative Frequency Load Distributions
The fatigue life of civil aircraft wing structures is related to the variations in stress experienced under the following five main types of loading: 1. Gust Loads; 2. In-flight maneuver loads; 3. Ground maneuver loads; 4. The once-per-flight loads resulting from the difference between in-flight and on-ground load levels, usually termed the Ground-Air-Ground (GAG)-cycle; 5. Local loads such as those arising from flaps, undercarriages, etc.
The method to determine the cumulative frequency of occurrence of loads 1 and 2 are presented in ESDU 69023 (1989) whereas for loads 3 in ESDU 75008 (1984).The GAG-cycle (load type 4) is derived from the in-flight gust and maneuver spectrum and the ground maneuver cumulative frequency distributions as described in ESDU 79024 (1979).Loads 5 are special cases not accounted for in the damage calculation presented herein.For sake of conciseness all the calculations regarding these kind of analysis are not reported.

Contributions to the Cumulative Damage -Fatigue Life
The damage calculation is performed for a structural joint between a wing lower skin and a stringer located close to the root buttock line.The main hypothesis on which this analysis is based is the univocal relationship between the stress in the joint and the bending moment at the wing root.The joint stress value is evaluated by FE analysis for a root bending moment of 1.0 kN m.It is equal to 0.2615 MPa.Since the entire work is focused on the life extension to be gained from the adoption of a MLC system, the S-N curve provided by ESDU 79024 (1979) is used.It is depicted in Figure 12.

Cumulative Damage Calculation -Fatigue Life Estimation
The total damage together with the estimated mean life are listed in Table 1for flight profile #1 (Short Range Mission) and in Table 2 for flight profile #2 (Long Range Mission).The life estimation, in number of flights, is calculated as the inverse of the total damage since it is assumed that the failure occurs when ΣD=1.0.Notice that the fatigue life is longer in case of short range mission (flight profile #1) because the airplane flights carrying a very small amount of fuel if compared to the that of the long range mission.The FLEFs (Fatigue Life Extension Factors) are in either case much greater than the unity, indicating a very good life extension, beyond the best expectations.

CONCLUSION REMARKS
In this paper, a conceptual design of an active control system for load alleviation during an unsteady longitudinal maneuvers is presented.An application to a business aircraft considered only as a test case-study has been performed.The system has been conceived to be able to alleviate the wing bending moment at a wing section near the wing root but by following always the same imposed maneuvering load factor.The LAS incorporates a Load Factor Feedback (LFF) to the elevators in order to perform a desired longitudinal maneuver by automatically acting on the elevators through a PID controller.The MLC is accomplished by observing the bending on the wing root section and by symmetrically acting on the ailerons by means of a simple P controller in order to shift the wing center of pressure inboard, and thus to minimize the difference between measured bending moment and 1-g bending moment.All numerical analyses aimed at simulating the aircraft behavior during maneuver with MLC-on or MLC-off are performed both by taking into account and by neglecting the flexibility of the aircraft.Indeed the synthesis of the controllers has been made by tuning the gains in either case, i.e. for rigid and elastic aircraft, in order to appreciate the different performance by keeping always the same limit gain and phase margins.Results of analyses performed for different dynamic pressures, Mach numbers and mass conditions, show attained wing bending reductions between 17% and 23% ,with minimum wing torsion and horizontal tail load augmentations (under 10%).Furthermore, the calculation of the necessary load alleviator servo power demonstrates also the possibility to adopt such a system with a relatively low dedicated power.Finally the estimation of the fatigue life extension of a wing lower skin joint located close to the wing root has been performed by using methods published by ESDU 79024 (1979), ESDU 69023 (1989) and ESDU 75008 (1984).The aim of the work is to demonstrate the effective fatigue life extension derived from the adoption of a MLC system.Thus analyses are performed for either case of MLC-on and off for two different mission profiles: a short range mission and a long range mission.The registered fatigue life extension factors are in either case much greater than the unity, indicating a very good life extension, well beyond the more positive previsions.The better result is obtained for the long range mission.In this case flight loads are prominent with respect to the ground ones, thus the benefit of having a MLC system aboard becomes much more relevant as re- gards the fatigue life extension.It should be noted that the impact on aircraft aerodynamic drag due to the activation of a LAS has been never accounted for in the present study.Indeed the load alleviators deflection produces a change in the spanwise aerodynamic distribution with consequent variation of the induced drag.Moreover if the load alleviation is carried-out by shifting the aerodynamic center of pressure inboard, the induced drag probably increases.Furthermore the airfoil camber augmentation leads to a wake drag increase and also to a wave drag increase at high Mach numbers.

Figure 1 :
Figure 1: LAS Macro-System. 0Eext ail HM ).Load Derivatives of Shear, Bending moment and Torsion are calculated for each load case (different Latin American Journal of Solids and Structures 13 (2016) 2298-2315altitude, Mach number and mass condition) at the WCS by following the procedure presented byPaletta et al. (2010).With the same symbol meanings(10) airplane flexibility is taken into account by considering the first 37 symmetric normal modes.

Figure 5 :
Figure 5: Vertical Load Factor, Comparison between Elastic and Rigid aircraft.

Figure 6 :
Figure 6: Control Surface deflections, Comparison between Elastic and Rigid aircraft.

Figure 10 :
Figure 10: Alleviation Factor AF, dependency upon the Mach Number.
Sensitivity versus the Dynamic Pressure (M=0.573)-Elastic A/C Sensitivity versus the Dynamic Pressure (M=0.573)-Rigid A

Table 1 :
Damage Calculation and Life Estimation -Flight Profile #1.

Table 2 :
Damage Calculation and Life Estimation -Flight Profile #2.