Comparative evaluation between mechanical and pneumatic cells for quartz flotation in the iron ore industry Mining Mineração

Flotation plays a relevant role in the concentration of iron ores. Conventional flotation technology employing mechanical machines and columns and also circuits combining both types of cells have been utilized in the iron ore industry. The top size of particles in the flotation circuit feed is 150 μm and the slimes below 10 μm are removed as overflow in hydrocyclone classification. The conventional flotation technology faces difficulties in achieving tailings with iron grades lower than 12% and concentrates with SiO2 grades lower than 1%, and requires long residence times, resulting in large volume machines and huge footprints. The pneumatic flotation technology was evaluated in the reverse flotation of quartz from an iron ore sample of the Iron Quadrangle, Brazil. Bench and industrial scale tests were conducted in pneumatic flotation machines at low residence time. Both tests were carried out in open circuit stages with the objective of comparison with mechanical cells. The bench scale tests were carried out in three stages (rougher, cleaner and recleaner) in an 11 L pneumatic cell aiming at final concentrate with maximum 2% SiO2 while the industrial tests were carried out in a 25 m3 pneumatic cell in the rougher stage aiming at comparison with a circuit of five 14 m3 cells in the rougher stage and four 14 m3 cells in the scavenger stage. The collision and particle-bubble adhesion occur in a step before the pulp reaches the pneumatic cell vessel. The results indicate the possibility of achieving concentrates with a SiO2 content of approximately 1% and tailings with iron contents lower than 10% with three stages (rougher, cleaner and recleaner) without the need of scavenger stages. Furthermore, the residence time was three times shorter than that required for conventional mechanical cells. The speed of the pulp at the entrance of the pneumatic cell strongly affects the quality of the concentrate.


Introduction
The flotation of iron ores is performed in circuits consisting of mechanical cells, columns, or a combination of both types of machines.The feed consists of particles in the size range between 10 μm and 150 μm.The slimes (fraction < 10 μm) are removed in hydrocyclones and the top size is limited to 5% to 10% > 150 μm.This wide range of particles size impairs process selectivity due to the possible differences in behavior concerning properties such as hydrophobicity, specific surface area, weight, etc. (Lima et al., 2013).
The flotation mechanism was investigated by Tomlinson and Fleming (1963), using a probabilistic concept between the probabilities of collision (Pc), adhesion (Pa) and a stable aggregate formation (Ps):

Pf = Pc x Pa x Ps
Different probability parameters are associated with different particle sizes in the flotation pulp.Thus, coarse particles have a high Pc and a low Pa, which helps to explain the difficulty of collecting these particles in the flotation process.Studies carried out by Hewitt et al. (1994) showed that the Pa increases with decreasing particle size and with increasing degree of hydrophobicity, the latter being achieved with increased collector dosage.Furthermore, fine particles have a low Pc and adhesion and high probability of retaining the bubble.
Current flotation systems utilized in the iron ore industry (mechanical cells and columns) are not effective for collecting quartz particles larger than 150 µm and smaller than 45 µm, and the loss of fine particles of iron minerals in the tailings fraction is high.Furthermore, these systems require multiple stages and long residence times to produce concentrates with maximum 2% of SiO 2 within market eq. 1 Comparative evaluation between mechanical and pneumatic cells for quartz flotation in the iron ore industry specifications and with minimal loss of iron in the tailings.Entrainment of particles into the froth phase is an important factor in the performance of the flotation process, especially concerning fine particle recovery.It has been observed that the entrained gangue recovery is often proportional to the water recovery (Trahar, 1981, Neethling andCilliers, 2009), although there is sometimes a non-linear relation-ship at low water recoveries, followed by a linear increase at higher water recoveries (Engelbrecht and Woodburn, 1975;Zheng et al., 2006, Neethling andCilliers, 2009).
A simplified model was proposed by Neethling and Cilliers (2002) to predict the entrainment factor as a function of the water recovery and the froth height.This investigation confirmed the experimentally observed relationship between gangue and water recovery, including its dependence on particle size, by using physics-based models for the liquid and solids behavior in the froth.It was concluded that there is a significant particle size effect on entrainment, in agreement with experimental observation (Neethling and Cilliers, 2009).Equation 2 was used as a simplified model for the calculation of entrainment.
The entrainment of fine iron mineral particles (<45 µm) into the froth can be one of the reasons for the difficulty in achieving tailings with low iron content (<12%) in traditional machines (mechanical and column cells) in the quartz reverse flotation of iron ores.The pneumatic flotation system was introduced in 1987, with the first opera-tion in Pennsylvania for coal flotation.Since then, the technology has been widely used for fine coal slurries, industrial minerals, ferrous ores, non-ferrous metal-bearing ores such as copper, lead, nickel and zinc, for the precious metals platinum, gold, and silver.The pneumatic machines have been used in a wide range of particle sizes, from 80% passing 45 µm to 80% passing 1000 µm (Ören et al., 2012).
Figure 1 illustrates a pneumatic flotation machine, where the pulp must be pumped at high pressure (2.5 to 3.0 bar) to promote the suction of air (selfaerated air) and the collision between mineral particles and bubbles under high energy.
The pressurized conditioned pulp feed to the pneumatic machine shown in Figure 1 promotes the self-aeration to the feed pipe: when the air mixes with the pulp, small diameter bubbles are created.Collision and adhesion with particles take place ahead of the distributor and the hydrophobic particles adhered to bubbles immediately migrate to the froth phase, while the hydrophilic particles follow the pulp phase to the underflow.The residence time is very low, not requiring probabilistic effects between particles and bubbles in the cell as in conventional machines (Imhof et al., 2002).
The main features of the pneumatic flotation are (Imhof et al., 2002;Uliana et al., 2013): • the mechanisms of collision and adhesion between particles and bubbles which occur with high efficiency, before the pulp reaches the cell vessel, reducing the required residence times; • low turbulence, reducing the likelihood of detachment of coarse particles, leading to concentrates with low SiO 2 content; • low drag of fine iron mineral particles to the froth, resulting in tailings fraction with low iron content; • generation of small diameter bubbles with high collection efficiency; • simplicity of operation and maintenance due to the absence of moving parts.
This paper reports the results and discussion of an investigation into the pneumatic machine used in the reverse flotation of quartz for in comparison with the conventional machines.

Bench scale tests
Bench scale tests were carried out in a pneumatic flotation machine of 11 L in the rougher, cleaner and recleaner continuous stages aiming to produce the final product (iron concentrate) with SiO 2 content below 2% and final tailings with maximum 10% of Fe.The tests were conducted in open circuit, where the first concentrate was used to feed the next stage.The recleaner concentrate was the final product, the combination of rougher, cleaner and recleaner tailings were the final tailings.The gas flowrate was controlled by a compressor.
The following conditions were used in the pneumatic flotation machine tests based on preliminary tests to define the best conditions for reagents dosages, pH, and physical operating conditions: • pulp solids concentration: 50% by weight; • pulp flowrate: 376 litres/hour; • residence time: 2.5 minutes in each stage, 7.5 minutes total.The residence time was calculated dividing the pulp flowrate by the cell net volume; • cornstarch dosage: 500g/t, added during the pulp conditioning for 3 minutes; • collector (etheramine EDA-C by Clariant) dosage: 80g/t, added during the pulp conditioning after the cornstarch for 1 minute; • pH: 10.5.
Feed, concentrates, and tailings were sampled for chemical analysis (Fe and SiO 2 ) and determination of size distribution and percent solids.
A representative iron ore sample from the Iron Quadrangle was used in the tests.Comparative tests in a 2600 mL conventional mechanical cell were conducted with the same sample and with the same reagents dosages and pH described above.Kinetic flotation tests were carried out in the mechanical bench scale machine, collecting tailings every two minutes for chemical analyses (Fe and SiO 2 ).All the tests, pneumatic and mechanical cells, were done in duplicate.

Industrial scale tests
Industrial scale tests were carried out to validate the bench scale results and the scale up.The tests were done in parallel with the conventional circuit: one pneumatic rougher cell of 25 m 3 was compared with nine me-chanical cells of 14 m 3 each.Figure 2 shows the comparative circuits for the industrial tests.

Figure 2
Comparative circuits for the industrial tests.

Comparative evaluation between mechanical and pneumatic cells for quartz flotation in the iron ore industry
The content of Fe in the pneumatic flotation tailings is almost stable in each stage.On the other hand, the Fe grades in the mechanical cells tailings are higher than those in the pneumatic cell, increasing from rougher to cleaner to recleaner.The higher grades of Fe in the tailings of the mechanical cell are related to the fractions of <45 µm, as shown in Figure 4.The entrainment is the main hypothesis for the higher losses of fine particles of iron bearing minerals in the tailings of the mechanical cell.
The loss of fine particles of iron minerals by entrainment can be related to the water recovery in the froth as stated by Neethling and Cilliers (2002).Figure 5 shows the water recovery in the froth for the different stages in the mechanical and pneumatic cells.
The water recovery is lower in all stages of the pneumatic cell compared to those in the mechanical cell.
Figure 6 shows the correlation between water recovery and iron recovery in the froth for mechanical cell and pneumatic cells.
Iron recovery in the froth strongly correlates (R 2 = 0.9537) with the water recovery in the froth for the mechanical cell.On the other hand, the correlation is weak (R 2 = 0.3605) for the pneumatic cell, indicating that entrainment is less relevant in this machine, regarding Fe recovery to the froth.The high water recovery on the froth for the mechanical cell is in agree-ment with the study of Lima et al (2016), where more than 96% of water in the froth and close to 90% of Fe recovery were observed in the scavenger stage.
Figure 7 compares the performance of the mechanical and pneumatic cells, over cumulative flotation time, in terms of grades of SiO 2 in the final concentrate and iron in the tailings.
The Pneumatic cell produced an iron concentrate with 0.8% SiO 2 after 7.5 minutes while the mechanical cell produced an iron concentrate with 2% SiO 2 after 16 minutes.The grade of iron in the pneumatic cell tailings was close to 6% during the three stages while this grade increased to 9% to 30% in the mechanical cells.The industrial tests showed that the froth depth is not so relevant in the pneumatic performance as is in the mechanical cells.Other physical parameters require better investigation regarding pneumatic flotation, such as the pulp density, pulp velocity, and ratio between air and pulp flow rates.These parameters seem to affect and control the pneumatic flotation performance.

Conclusions
The pneumatic cell has a great potential for quartz reverse flotation in the iron ore industry, with the possibility of reducing the flotation time and increasing the metallic recovery.One stage of pneumatic flotation can replace the rougher and scavenger stages of mechanical cells, with a strong decrease in the footprint and enhanced flotation performance for iron ore.The results of the investigation involving bench scale and industrial tests indicated that the entrainment of fine iron bearing mineral particles is lower in the pneumatic cell.Although there is greater operational simplicity, the effect of some parameters requires better in-vestigation and understanding regarding the pneumatic cell, such as pulp density, pulp velocity, and the ratio between air and pulp flow rates.The bench scale pneumatic cell of 11 L of volume can be easily operated to estimate results for the industrial scale cell but the scaling up still requires investigation.

Figure 3
Figure 3 compares the Fe content in the rougher, cleaner and recleaner

Figure 3
Figure 3 Comparative Fe content in the tailings of the flotation stages.

Figure 4
Figure 4 Content of Fe in the <45µm in the tailings.

Figure 5
Figure 5Water recovery in the froth.

Figure 6
Figure 6 Water recovery in the froth vs Fe recovery in the froth -Mechanical and pneumatic cells.

Figure 8
Figure 8 compares the results of the industrial flotation tests, regarding % of Fe in the froth, % of SiO 2 in the rougher concentrate, metallic recovery and Gaudin selec- Figure 7 Comparative grades of SiO 2 in the concentrate and Fe in the tailings.