Platinum-Based Alloys: Investigation of the Effect of Impurities Content on Creep Rate, Rupture Time and Relative Elongation at High Temperatures

Abstract

This paper presents the results of research of the effect of impurities content on high-temperature resistance of selected platinum alloys. Alloys of following systems were investigated: Pt-Rh, Pt-Rh-Pd, Pt-Rh-Pd-Ru and Pt-Rh-Pd-Ir-Au. Universal device for tensile testing of materials at high temperatures was used for examination. Investigations were carried out in a temperature range of 1300-1400 °C, with a stress of 5 MPa. It was observed that an increase in content of impurities in tested alloys at high temperatures, and at stated conditions of stress, caused a noticeable increase in creep rate while reducing rupture time and relative elongation. Experimental results confirmed that probability of brittle fracture decreases with decreasing impurity content in the alloys. Binary and multicomponent alloys of Pt-Rh, Pt-Pd-Rh, Pt-Rh-Pd-Ru and Pt-Rh-Pd-Ir-Au systems are primarily used in conditions of high temperature, and accordingly, presented results contribute to a better understanding of their behavior in such working conditions.

Keywords:
Platinum-based alloys; impurities; creep rate; rupture time; relative elongation

1. Introduction

Platinum (Pt) is dense, stable, malleable, ductile, biologically compatible, gray-white, precious, rare transition metal with good electrical conductivity, belonging to platinum group metals (PMGs) which also include iridium (Ir), Osmium (Os), Palladium (Pd), Rhodium (Rh) and Ruthenium (Ru). All this metals are extremely rare, very durable and due to their high price, often recycled.

Annual production of platinum is around few hundred tones making it very scarce and valuable. The largest amount of platinum is used in jewelry industry (about 40% of annual production), but this metal is also crucial for many catalytic processes, and holds important role for electronic industry and medicine.

Platinum is often alloyed with other PGMs in order to improve durability at high temperatures. Interest of researches in platinum based alloys is constantly growing¹. These types of alloys are used in: glass industry^2,3, fertilizer plants^4-6, temperature measurement⁷, environment protection⁸, jewelry production^9,10, shape memory applications^11,12 and medicine¹³.

Different Pt-based alloys are primarily used in various high temperature applications, so knowledge of their properties under such conditions is crucial for successful utilization.

Alloys of platinum with rhodium content up to 20% are most commonly used in high temperature aplications, but compositions with rhodium up to 30% are also utilized. Platinum-iridium allys are not used often like platinum-rhodium alloys, but iridium in small amout (up to 1%) can improve platinum microstructure stability at high temperatures, without significantly affecting mechnical strenght. Higher contents of iridium in platinum-based alloys can lead to poor oxidation resistance and ebrittlement. Using gold as alloying element leads to significant increase of molten glass contact angle on surface of platinum-based alloy.

Some of platinum-based alloys published research results include:

• thermodynamics and phase equilibrium of binary Pt-Rh system¹⁴.

• thermal and mechanical properties of Pt-Rh alloys¹⁵.

• microstructural analysis of selected platinum alloys used in industry and jewelry making (including PtRh10, PtRh30, Pt-5Ru, Pt-5Ir, Pt-5Au and Pt-25Ir-15Rh)¹⁶.

• Pt-Rh, Pt-Pd, Pd-Rh and Pt-Pd-Rh phase diagrams examined using Monte Carlo simulation method in combination with MEAM method and optimized parameters¹⁷.

• creep rate and rupture time of Pt-Rh alloys at high temperatures¹⁸.

The aim of this paper is to examine the impact of harmful impurities on high temperature resistance of Pt-Rh, Pt-Rh-Pd, Pt-Rh-Pd and Pt-Ru-Rh-Pd-Ir-Au alloys.

The presence of chemical elements - impurities in the platinum metals and alloys is associated with the composition of the starting ore deposits as well as the technological processes for their obtaining, processing and exploitation in industrial conditions^19-21.

The presence of impurities in platinum metals and alloys has a large impact on their physical and mechanical properties. For this reason, the purity of platinum metals and alloys is one of their main characteristics. It is determined by calculation, from the difference between 100% weight of the metal and the sum of percentages of 10-15 control impurities. In addition, in the total number of control impurities, as a rule, there are the platinum group metals and gold. Impurities such as Rh, Ru, Pd, Ir and Au lead to the improvement of mechanical properties of platinum, ie to increase of its high temperature resistance. In addition to these "good" impurities there are harmful impurities, 50-70 so-called non control impurities, in a total concentration of 10^-2 - 10^-3% (wt.%). This work aimed to show how various contents of impurities affect the high-temperature characteristics of platinum materials, at a constant temperature and stress. The results are only part of the multi year researches of platinum materials at high temperatures, which find application in the glass industry for molding optical fiber.

2. Experimental

Platinum, rhodium and palladium for alloys production have been obtained as a side product in the production of electrolytic copper RTB, Serbia. By additional refinement the necessary purity for samples production has been achieved (99.98% for Pt, 99.95% for Rh and Pd 99.98%). The composition of the samples is given in Table 1.

Table 1
The content of alloying elements in the investigated alloys (mass%)

Alloy	Rh / % (wt.)	Pd / % (wt.)	Ru / % (wt.)	Ir / % (wt.)	Au / % (wt.)
PtRh7	7	-	-	-	-
PtRh10	10	-	-	-	-
PtRh5Pd15	5	15	-	-	-
PtRh10Pd25Ru1.5	10	25	1.5	-	-
PtRh20Pd10Ir0.1Au0.1	20	10	-	0.1	0.1

Impurities in the samples were characteristic for raw material of Bor deposits - Si, Sb, Fe, Al, Mg, Ag, Bi, Sb, As, Cu.

Melting of the samples was carried out in a medium-frequency induction furnace. Annealing of the samples was carried out in an electro resistant furnace type LP08, for 20 minutes at 900°C.

For testing the mechanical properties of samples at high temperatures a universal device for tensile testing of materials at high temperatures, by manufacturer Karl Frank, type 81221, was used.

Chemical analysis of materials for samples was performed on atomic absorption spectrophotometer. Examination of the microstructure was performed on samples measuring 1,7x1,7 mm, which were prepared according to standard procedure - grinding, polishing (polishing machine ROWA E KG) with 0,05µm Al₂O₃ powder, and etched a few seconds with aqua regia (100cm³ HCl and 30cm³ HNO₃). Changes in the structure were observed using optical and scanning electron microscope. Optical microscopy was performed on metallographic microscope EPYTIP 2, at different magnifications. Scanning-electron microscopy (SEM) was performed on electronic microscope JEOL JSM-6610LV with resolution of 10 nm on 20keV, accelerating voltage of 3-30 kV and magnification up to 300000x.

3. Results and Discussion

In order to supplement the existing database of platinum and platinum metals, originating from the Bor deposites in Serbia, as well as having the information about the practical implementation of the above mentioned at high temperatures, investigations were carried out on the influence of impurities on the mechanical properties of the alloys of Pt-Rh, Pt-Rh-Pd, Pt-Rh-Pd-Ru and Pt-Rh-Pd-Ir-Au systems, with platinum as base metal, and alloying elements Rh (15-20 wt%), Pd (10-25 wt%), Ru (1.5% wt.), Ir (0.1% wt.) and Au (0.1% wt.).

Since platinum metals alloys can contain a range of impurities, it is very difficult to determine the individual effect of each one to high-temperature resistance of alloys. For the practical application of platinum alloys, it is important to have knowledge of individual as well as the group effect of impurities on the creep resistance (creep life) and the destruction of the alloys.

The values of the minimum creep rate (in the rest of paper creep rate) and rupture time of the alloy PtRh7 at 1300 and 1400 °C, at a stress of 5 MPa, are given in Table 2.

Table 2
Characteristics of high-temperature resistance of alloy PtRh7 depending on impurity content at 1300 and 1400 °C and stress of 5 MPa

Sample	Content of impurities / % (wt.)							έ / % h-1		t / h
	Si	Sb	Fe	Cu	Pb	Al	Mg	1300 °C	1400 °C	1300 °C	1400 °C
1	0.013	0.007	< 0.01	0.0073	0.005	0.002	0.006	0.42	1.14	55	28
2	0.007	0.004	< 0.01	-	0.003	< 0.002	0.003	0.18	0.96	63	38
3	0.008	0.006	< 0.01	0.005	0.004	< 0.002	0.013	0.132	0.582	56	40
4	0.01	0.003	< 0.01	-	0.001	< 0.002	-	0.15	0.552	104	34
5	-	-	< 0.01	-	< 0.001	< 0.002	-	0.198	0.906	86	46
6	-	-	< 0.01	-	< 0.001	< 0.002		0.186	1.14	85	47
7	-	-	< 0.01	-	< 0.001	< 0.002		0.20	0.582	103	54

• ^*
  all elements with symbol < are below the detection limit of AAS (method used to determine the content)

For PtRh7 alloy, in the temperature interval of 1300-1400 °C, at a stress of 5 MPa, based on the results shown in Table 2, at the total content of the impurities 0.05% (sample No. 1) creep resistance is twice as big, and the rupture time twice shorter, as compared with the sample number 7, wherein the total impurity content is 0.013%.

Based on the results in Table 2, it can be seen that in the total content of impurities, the largest share belongs to: Si, Fe, Al and Mg.

The effect of impurities on creep rate, rupture time and relative elongation, at the temperature of 1400 °C, at a stress of 5 MPa, for the alloys PtRh10, PtRh5Pd15 and PtRh10Pd25Ru1.5 is shown in Tables 3, 4 and 5.

Table 3
The values of the creep rate, rupture time and relative elongation depending on the content of impurities at a temperature of 1400 °C, at a stress of 5 MPa, for the alloy PtRh10

Sample	Content of impurities / % (wt.)						έ / % h-1	t / h	A / %
	Fe	Al	Si	Mg	∑ Fe,Al, Si,Mg	Ca
1	0.004	< 0.002	0.001	0.01	0.0152	-	0.122	217	44
2	0.005	0.039	0.004	0.033	0.076	-	0.44	83	44.5
3	0.07	0.025	< 0.001	< 0.01	0.095	-	0.35	79	34
4	0.06	0.012	0.001	0.024	0.097	-	0.35	88	34
5	0.04	0.028	< 0.001	< 0.01	0.032	0.03	0.35	85	36
6	0.04	0.035	< 0.001	0.030	0.105	0.04	0.47	71	42
7	0.06	0.031	0.001	< 0.01	0.092	0.033	0.29	70	27
8	0.07	0.04	< 0.001	0.022	0.132	0.024	0.182	69	30
9	0.038	0.022	< 0.001	0.016	0.076	0.02	0.222	97	43

• ^*
  all elements with symbol < are below the detection limit of AAS (method used to determine the content)
• ^**
  alloys in each sample contained 0.001% Ag, and cumulative 0.005% of Cu, Ni, Pb, Sb and Zn

Table 4
The values of the creep rate, rupture time and relative elongation depending on the content of impurities at a temperature of 1400 °C, at a stress of 5 MPa, for the alloy PtRh5Pd15

Sample	Content of impurities / % (wt.)						έ / % h-1	t / h	A / %
	Fe	Al	Si	Mg	∑ Fe,Al, Si,Mg	Ca
1	< 0.004	0.009	0.018	< 0.01	0.026	0.011	1.3	20	32
2	< 0.004	0.014	0.001	0.022	0.036	0.011	1.3	17	29
3	0.004	0.009	0.002	< 0.01	0.051	< 0.01	2.4	13	39

• ^*
  all elements with symbol < are below the detection limit of AAS (method used to determine the content)
• ^**
  All samples contain < 0.005% Σ : Cu, Ni and Zn; Samples No. 1 and No. 2 contain 0.001% Ag; Sample No. 3 contains 0.01% Ag

Table 5
The values of the creep rate, rupture time and relative elongation depending on the content of impurities at a temperature of 1400 °C, at a stress of 5 MPa, for the alloy PtRh10Pd25Ru1.5

Sample	Content of impurities / % (wt.)				έ / % h-1	t / h	A / %
	Fe	Cu	Al	Si
1	0.01	0.004	< 0.002	< 0.001	0.39	53	31
2	0.065	0.003	< 0.002	0.019	0.43	28.5	11.5
3	0.013	0.006	0.018	0.019	0.35	24	10
4	0.053	0.004	< 0.002	< 0.001	0.48	29	16
5	0.04	0.003	0.018	0.01	0.46	29	12.5

• ^*
  all elements with symbol < are below the detection limit of AAS (method used to determine the content)
• ^**
  investigated alloy also contains < 0.003% Mg; and < 0.005% of Zn, Ni and Pb

Based on the results presented in Table 3, for the alloy PtRh10, at a temperature of 1400 °C and a stress of 5 MPa, the same rule applies as to the alloy PtRh7 under the same conditions. At the minimum content of non-precious impurities (Fe, Al, Si and Mg) of 0.015% (sample No. 1), properties that characterize the resistance at high temperatures are 1.5-3.0 times higher than in sample No. 8 with the maximum content of the afore mentioned impurities of 0.132 %. Also, from Table 3, it can be seen that the rupture time significantly decreases with increasing content of impurities, while the relative elongation slightly decreases with the increase of the total content of impurities. Similar rules were also observed for alloys PtRh5Pd15 and PtRh10Pd25Ru1.5.

The characteristics of high temperature resistance of PtRh20Pd10Ir0.1Au0.1 alloy, at a temperature of 1400 ° C and a stress of 5 MPa, are presented in Table 6.

Table 6
The characteristics of high temperature resistance of alloy PtRh20Pd10Ir0.1Au0.1 depending on the total content of impurities

Sample	Content of impurities / 10-3 % (wt.)												έ /% h-1	t / h	A / %
	Ag	Fe	Mg	Al	Si	Pb	Sb	Sn	Zn	Cu	Ni	Σ
1	0.5	2.6	0.03	5	0.02	5	0.03	0.07	0.8	0.8	0.7	15.55	0.07	340	48
2	19	6	3	3	4	8	8	10	10	8	4	83	0.14	76	12

Based on the results in Table 6 it can be concluded that for the tested alloy with the increase in the total content of ten most abundant impurities (Al, Fe, Si, Mg, Pb, Sb, Zn, Sn, Cu, Ni) from 0.01% to 0.083% wt., at a temperature of 1400 °C and a stress of 5 MPa, rupture time decreases five times, relative elongation four times and creep rate increases twice, which shows excellent agreement of the results with literature data^19,21,22.

Based on the results presented above it can be concluded that increasing the sum of specified impurities results in a negative impact on the lifetime and plasticity of alloy PtRh20Pd10Ir0.1Au0.1, at high temperatures. Increasing the total content of impurities in the examined alloy from 0.015 to 0.083% (wt.) was followed by the accumulation of impurity atoms in the grain and subgrain boundaries, as shown in Figure 1.

Figure 1
The microstructure of the sample PtRh20Pd10Ir0.1Au0.1 with total content of the impurities a) 0.015 % (wt.), 70x ; b) 0.083% (wt.), (magnification 200x)

It is obvious that the accumulation of impurity atoms at the grain boundaries leads to an increase in the total volume of the borders, which results in the creation of a very brittle structure that cracks relatively quickly in the processing as well as in the exploatation process at high temperatures. Namely, at the concentration of impurities of 0.01% and lower, the changes in structure are not observed and alloy possesses high plasticity and temperature resistance. Increasing the concentration of any impurity, to the hundredths or thousandths of percent, in platinum alloys, does not cause changes in composition of grain boundaries which would be observed under an optical microscope, but could be substantially responsible for the decrease of the relative elongation and the destruction time at 1400 °C.

The structure of alloy PtRh20Pd10Ir0.1Au0.1 without the presence of impurities is presented in Figure 2. The grain size before testing was 0.057 mm, and after the high temperature creep test it was 0.0267 mm.

Figure 2
Microstructure of sample composition PtRh20Pd10Ir0.1Au0.1 without impurities: a) before and b) after creep, at 1400 °C and a stress of 5MPa, close to the rupture point (magnification 200x)

Microstructure of PtRh20Pd10Ir0.1Au0.1 alloy sample, containing impurities above 0.0286% (wt.), is shown in Figure 3. It is characterized by high porosity and difference in grain size before (average grain diameter is 0.034 mm) and after the high temperature creep (grain size is 0.174 mm).

Figure 3
Microstructure of sample composition PtRh20Pd10Ir0.1Au0.1 with impurities content of 0.0286%: a) before and b) after creep, at 1400 °C and a stress of 5MPa, close to the rupture point (magnification 200x)

Based on these results, it can be concluded that after plastic deformation by creep testing, average grain diameter of alloy, with impurities in an amount of 0.0286%, is significantly bigger compared to the average grain diameter of the alloy without impurities. Impurities accumulated in the grain boundaries have resulted in a large porosity and accelerated intercrystalline destruction.

Intercrystalline fracture (Figure 4) occurs at grain boundaries and is characteristic when the material is exposed to low stress, low deformation speed and high temperatures.

Increased sensitivity of platinum alloys at high temperatures, containing a large number of impurities indicates to particular importance of the purity of the initial metals used for production of alloy.

Figure 4
Examples of intercrystalline fracture at a) 800, b) 900 and c) 1000 °C for PtRh20Pd10Ir0.1Au0.1 alloy

Table 7 shows the influence of the control impurities present in refined platinum, rhodium and palladium on a high-temperature resistance of alloy PtRh20Pd10Ir0.1Au0.1 at 1400 °C, at a stress of 5 MPa.

Table 7
The influence of control impurities content in the alloy PtRh20Pd10Ir0.1Au0.1 on high temperature properties

Sample	Content of the impurities / 10-3 % (wt.)									έ /% h-1	t / h	A / %
	Si	Fe	Pb	Ag	Ti	Cu	Ni	Mg	Σ
1	1.8	0.3	0.6	0.7	-	0.2	-	0.8	4.4	0.09	175	23
2	1.6	0.1	0.8	0.9	0.2	-	0.6	0.8	5.	0.24	216	65
3	0.4	1.7	0.6	0.7	-	0.2	-	0.8	4.4	0.12	276	50
4	0.2	1.5	0.8	0.9	0.2	-	0.6	0.8	5	0.05	430	70

It is obvious that, when comparing the same or similar concentrations of Pb, Ag, and Mg, rupture time of the obtained samples is higher at lower Si content. The content of Fe, Cu, Ni and Ti within the specified concentration does not show a significant effect on the characteristics of high temperature resistance and plasticity of samples made ​​from different charges.

Constant and controlled composition of impurities in the starting charges is the main condition for obtaining platinum alloys with stable structures and characteristics. For that purpose, for the synthesis of alloys one should always strive to use platinum metals with high purity, which is achieved by multistage refining of them, so the final products would be of satisfying composition and quality.

On the mutual effect of impurities with platinum group metals, as well as their interaction, it is best to judge on the basis of the phase diagrams^19-21. When considering the binary and multicomponent phase diagrams only interaction of 2-6 primary and alloying elements with a maximum of ten impurities should be taken into account.

Impurities such as Fe, Cu, Ni, form solid solutions with platinum group metals, having a melting point lower than the melting point of the main and alloying elements. From such solid solutions, with a decrease in temperature, different transformations occur with formation of chemical compounds, damaging in the further exploitation of such materials²².

Impurities such as Si, Ag, Pb, Sn, Sb, Bi, P, S, Se, Te, As, Mg, Zn, Ba, Al, with platinum group metals form sparingly soluble and brittle compounds²². The resulting compounds (such as Pt and Pd silicides), lead to relatively rapid fracture and destruction of materials at high temperature operation.

The probability of interaction of impurities with the platinum group metals is even greater and more significant if the concentration of the impurities is higher in those metals.

Technological and exploitation properties of platinum metals and alloys can be significantly altered in the presence of very small amounts of impurities (within hundredths and thousandths of a percent). In the presence of very small contents of impurities in the volume of metals or alloys, their concentration in certain zones (intercrystalline zone or zone within the crystal-grain itself) can be very high.

The equilibrium segregation of impurities takes, by rule, an area of one to ten nanometers, although in most cases an enrichment in impurities is limited by monolayer segregation of atoms equal to or slightly greater than the intercrystal zone with width of the 2-3 atomic layers.

The equilibrium segregation occurs as a result of diffusion of impurities to the grain boundaries while creating a concentration gradient. It is most common for phase diagrams with low solubility of impurities in the crystal lattice metal-base, as well as for the large differences in atomic diameters of impurities and the base metal.

For the studied phase diagrams of platinum with Fe, Ni, and Cu grain boundaries are even more enriched with impurities if their solubility limit is lower. With the reduction of impurities solubility limit up to the 1x10^-3 % (at.), their concentration in the intercrystal zone of the metal-base may reach 10% (at.), ie. may be 10.000 times larger than in alloy volume.

Based on the afore mentioned, we reach the conclusion that practically insoluble or slightly soluble impurities such as Ba, P, As, Si, Bi and Pb show a high tendency towards forming equilibrium segregations, compared to the Fe, Ni, Cu, Ag, Mg, Zn, Al and Sb which with platinum form a continuous series or wide area (on platinum side) of solid solutions.

The equilibrium segregation of impurities leads to a reduction in deformation energy of the crystal lattice in the area of their existence, while reducing the Gibbs energy of intergrain borders.

Impurities accumulated at the grain boundaries may react with each other and lead to strengthening or weakening of segregations of that element or some other element.

In the first case, at the same sign of the atomic range of deviation between two impurities compared to metal-base, the intercrystalline zone will be more enriched with atoms of impurity which has a greater range of deviation in absolute values. In the second case, at the different sign of the atomic deviation and equal atomic concentrations of the two impurities, it comes to the formation of complex of atoms of those impurities and the equilibrium segregation weakens.

Segregation gets stronger in the case when the impurities absorbed on the surface of the crystal have the same sign and close values of deviation range, at the same time.

In this way, it can be expected that in cases when the removal of hamful impurities from the alloy is very difficult, their impact can be also minimized with the introduction of less harmful impurity or impurity with opposite sign of deviation range.

Based on the atomic diameter of platinum which is 0.139 nm, it is possible to form a series of ranges of deviation of impurities atomic diameters.

Size of the range of deviation (Δr) of atomic diameters of platinum and impurities, in the case when the diameter of platinum is larger (Δr +) or smaller (-Δr) than diameters of impurities is given in Table 8.

Table 8
Values of the range of deviation (Δr) for impurities

Element	Δr / nm	Element	Δr / nm
Zn	+0.006	As	-0.009
Si	+0.021	Sn	-0.012
P	+0.021	Mg	-0.021
Cu	+0.011	Zr	-0.021
Fe	+0.015	Sb	-0.012
Cr	+0.014	Pb	-0.036
Co	+0.014	Y	-0.039
Ni	+0.014	Bi	-0.016
Al	-0.004	Ca	-0.058
Ag	-0.005	Ba	-0.078
Ti	-0.007	K	-0.088

Based on the values shown in Table 8 it can be concluded that Zr reduces the equilibrium segregation and negative impact of impurities, such as Si and P in the investigated platinum alloys. Bismuth can somewhat neutralize the negative impact and accumulation of impurities such as Fe, Cu, Cr, Co, As and Ni.

The most severe form is the presence of impurities with approximate values of the divergency range, and of the same sign, such as Al and Ag as a pair, and Zn and Si as a second pair. In these cases probability of equilibrium segregation of each pair of impurities increases, as well as their negative impact on the technological and exploitation properties of platinum alloys.

However, in practical terms it is difficult to predict and even harder to manage the equilibrium segregation process of impurities in platinum alloys.

In real conditions in the formation of equilibrium segregation dozen of impurities can participate and that process can be very dependent on their mutual effect, interactions with the metal-base and alloying elements with simultaneous dependence of the temperature-time factor.

4. Conclusion

In this paper are presented results of the influence of individual impurities, as well as groups of impurities on resistance to plastic deformation and fracture at elevated temperatures, for the following alloys: PRh7, PtRh10, PtRh5Pd15, PtRh10Pd25Ru1.5 and PtRh20Pd10Ir0.1Au0.1.

Generally, in all investigated alloys, at elevated temperatures,with increasing of total content of impurities (Fe, Si, Al and Mg) from 0.013 to 0.068% (wt.) it was observed an increase in creep rate, alongside reduction of relative elongation and time to fracture.

The increase in total impurity content (from 0.015-0.083% (wt.)) in investigated alloys is accompanied by accumulation of their atoms at grain boundaries, resulting in occurrence of brittle and fragile structure.

At the same or similar contents of Pb, Ag and Mg, time to fracture is longer, at lower Si contents. The content of Fe, Cu, Ni and Ti within the limits of observed contents does not show significant negative impact on the high temperature properties of the alloy.

For the alloys PtRh10, PtRh5Pd15 and PtRh10Pd25Ru1.5 the rupture time significantly decreases with increasing content of impurities, while the relative elongation slightly decreases with the increase of the total content of impurities.

For PtRh20Pd10Ir0.1Au0.1 alloy resuts of investigation are showing that with increase in total content of ten most abundant impurities (Al, Fe, Si, Mg, Pb, Sb, Zn, Sn, Cu, Ni) from 0.01% to 0.083% wt., rupture time decreases five times, relative elongation four times and creep rate increases twice, which is in agreement with literature data.

Based on these results, it can be concluded that after plastic deformation by creep testing, average grain diameter of alloy, with impurities in an amount of 0.0286%, is significantly bigger compared to the average grain diameter of the alloy without impurities. Impurities accumulated in the grain boundaries have resulted in a large porosity and accelerated intercrystalline destruction.

The probability of interaction of impurities with the platinum group metals is even greater and more significant if the concentration of the impurities is higher in those metals.

Technological and exploitation properties of platinum metals and alloys can be significantly altered even in the presence of very small amounts of impurities because their concentration in certain zones (intercrystalline zone or zone within the crystal-grain itself) can be very high. Based on the afore mentioned, we reach the conclusion that practically insoluble or slightly soluble impurities such as Ba, P, As, Si, Bi and Pb show a high tendency towards forming equilibrium segregations, compared to the Fe, Ni, Cu, Ag, Mg, Zn, Al and Sb which with platinum form a continuous series or wide area (on platinum side) of solid solutions.

Impurities accumulated at the grain boundaries may react with each other and lead to strengthening or weakening of segregations of that element or some other element.

Alloys of Pt-Rh, Pt-Pd-Rh, Pt-Rh-Pd-Ru and Pt-Rh-Pd-Ir-Au systems are primarily used in high temperature conditions, and accordingly, presented results contribute to a better understanding of their behavior in such working conditions.

5. Acknowledgement

The research results presented in this paper are the result of technological development project TR 34029 "Development of production technology of Pd catalyst-catchers to reduce losses of platinum in high temperature catalysis processes", funded by the Ministry of Education, Science and Technological Development.

6. References

• ¹
  Gavin H. Platinum group metals research from a global perspective. Platinum Metals Review 2010;54(3):166-171.
• ²
  Preston E. Platinum in the glass industry. Platinum Metals Review 1960;4(2):48-55.
• ³
  Couderc C. Platinum Group Metals in Glass Making. Platinum Metals Review 2010;54(3):186-191.
• ⁴
  Ning Y, Yang Z, Zhao H. Platinum Recovery by Palladium Alloy Catchment Gauzes in nitric Acid Plants. Platinum Metals Review 1996;40(2):80-87.
• ⁵
  Yuantao N, Zhengfen Y. Platinum Loss from Alloy Catalyst Gauzes in Nitric Acid Plants. Platinum Metals Review 1999;43(2):62-69.
• ⁶
  Trumić B, Stanković D, Trujić V. Examining the surfaces in used platinum catalysts. Journal of Mining and Metallurgy B 2009;45(1):79-87.
• ⁷
  Wu B, Liu G. Platinum: Platinum-Rhodium Thermocouple Wire. Platinum Metals Review 1997;41(2):81-85.
• ⁸
  Funabiki M, Yamada T, Kayano K. Auto exhaust catalysts. Catalysis Today 1991;10(1):33-43.
• ⁹
  Biggs T, Taylor SS, van der Lingen E. The Hardening of Platinum Alloys for Potential Jewellery Application. Platinum Metals Review 2005;49(1):2-15.
• ¹⁰
  Wright JC. Jewellery-Related Properties of Platinum Low Thermal Diffusivity Permits Use of Laser Welding for Jewellery Manufacture. Platinum Metals Review 2002;46(2):66-72.
• ¹¹
  Biggs T, Cortie MB, Witcomb MJ, Cornish LA. Platinum Alloys for Shape Memory Applications. Platinum Metals Review 2003;47(4):142-156.
• ¹²
  Biggs T, Witcomb MJ, Cornish LA. Martensite-type transformations in platinum alloys. Materials Science and Engineering: A 1999;273-275:204-207.
• ¹³
  Xiao F, Zhao F, Mei D, Mo Z, Zeng B. Nonenzymatic glucose sensor based on ultrasonic-electrodeposition of bimetallic PtM (M = Ru, Pd and Au) nanoparticles on carbon nanotubes-ionic liquid composite film. Biosensors and Bioelectronics 2009;24(12):3481-3486.
• ¹⁴
  Jacob KT, Priya S, Waseda Y. Thermodynamic properties and phase equilibria for Pt-Rh alloys. Metallurgical and Materials Transactions A 1998;29(6):1545-1550.
• ¹⁵
  Dereli G, Cagin T, Uludogan M, Tomak M. Thermal and mechanical properties of Pt-Rh alloys. Philosophical Magazine Letters 1997;75(4):209-218.
• ¹⁶
  Battaini P. Microstructure Analysis of Selected Platinum Alloys. Platinum Metals Review 2011;55(2):74-83.
• ¹⁷
  Luyten J, de Keyzer J, Wollants P, Creemers C. Construction of modified embedded atom method potentials for the study of the bulk phase behaviour in binary Pt-Rh, Pt-Pd, Pd-Rh and ternary Pt-Pd-Rh alloys. Calphad 2009;33(2):370-376.
• ¹⁸
  Trumić B, Gomidželović L, Marjanović S, Krstić V, Ivanović A, Dimitrijević S. Pt-Rh Alloys: Investigation of Creep Rate and Rupture Time at High Temperatures. Materials Testing 2013;55(1):38-42.
• ¹⁹
  Ritvin EI, Medovoi LA. Vlianie fiziko-himicheskoj sledi na zharoprochnost merallicheskih materialov. Moskva: Nauka; 1974.
• ²⁰
  Savickij EM, Poljakova VP, Gorina NB, Roshan NR. Metalovedenie platinovih metalov. Moskva: Metalurgija; 1975.
• ²¹
  Zaharov MV, Zaharov AM. Zharoprochnie splavi. Moskva: Metalurgija; 1983.
• ²²
  Ritvin EI. Zharoprochnost platinovih splavov. Moskva: Metalurgija; 1987.

Publication Dates

• Publication in this collection
  05 Jan 2017
• Date of issue
  Jan-Feb 2017

History

• Received
  22 Mar 2016
• Reviewed
  07 Oct 2016
• Accepted
  21 Nov 2016