Abstract
Biosurfactants have many advantages over synthetic surfactants but have higher production costs. Identifying microorganisms with high production capacities for these molecules and optimizing their growth conditions can reduce cost. The present work aimed to isolate and identify a fungus with high biosurfactant production capacity, optimize its growth conditions in a low cost culture medium, and characterize the chemical structure of the biosurfactant molecule. The fungal strain UFSM-BAS-01 was isolated from soil contaminated with hydrocarbons and identified as Fusarium fujikuroi. To optimize biosurfactant production, a Plackett–Burman design and a central composite rotational design were used. The variables evaluated were pH, incubation period, temperature, agitation and amount of inoculum in a liquid medium containing glucose. The partial structure of the biosurfactant molecule was identified by nuclear magnetic resonance spectrometry. F. fujikuroi reduced surface tension from 72 to 20 mN m−1 under the optimized conditions of pH 5.0, 37 °C and 7 days of incubation with 190 rpm agitation. The partial identification of the structure of the biosurfactant demonstrated the presence of an α,β-trehalose. The present study is the first report of the biosynthesis of this compound by F. fujikuroi, suggesting that the biosurfactant produced belongs to the class of trehalolipids.
Keywords
Giberella fujikuroi; Surface tension; NMR spectroscopy; α,β-Trehalose; Trehalolipids
Introduction
Biosurfactants are secondary metabolites produced by microorganisms under specific growth conditions. Biosurfactants have an amphiphilic structure, enabling them to reduce surface and interfacial tension in water–oil and oil–water systems. Biosurfactants can be classified into several classes: glycolipids, lipopeptides, lipoproteins, phospholipids, fatty acids, polymeric biosurfactants and particulate biosurfactants.11 Cameotra SS, Makkar RS, Kaur J, Mehta SK. Synthesis of biosurfactants and their advantages to microorganisms and mankind. Adv Exp Med Biol. 2010;672:261-280. Their structural diversity allows biosurfactants to perform a variety of functions in the petrochemical, environmental, pharmaceutical, food, and agricultural industries, among others.22 Joshi SJ, Geetha SJ, Desai AJ. Characterization and application of biosurfactant produced by Bacillus licheniformis R2. Appl Biochem Biotechnol. 2015;177:346-361.
Compared to synthetic surfactants, biosurfactants present lower toxicity, higher biodegradability, greater resistance to extreme environmental conditions, are produced from renewable sources and have greater ecological acceptability.33 Jain RM, Mody K, Joshi N, Mishra A, Jha B. Production and structural characterization of biosurfactant produced by an alkaliphilic bacterium, Klebsiella sp.: evaluation of different carbon sources. Colloids Surf B Biointerfaces. 2013;108:199-204. Despite these advantages, a limitation to the industrial use of biosurfactants is their higher production costs compared to synthetic surfactants.44 Joice PA, Parthasarathi R. Optimization of biosurfactant production from Pseudomonas aeruginosa PBSC1. Int J Curr Microbiol Appl Sci. 2014;3:140-151. One means of reducing these costs is to identify and use microorganisms with high production capacities for these molecules. Within the diversity of known microorganisms, few are good producers of biosurfactants. Some fungi can produce larger amounts of biosurfactants than bacteria, which is explained by their cell wall stiffness.55 Bhardwaj G, Cameotra SS, Chopra HK. Isolation and purification of a new enamide biosurfactant from Fusarium proliferatum using rice-bran. RSC Adv. 2015;5:54783-54792.
Another way to reduce the cost of biosurfactants is to optimize growth medium conditions for the producing microorganisms. Several environmental factors influence biosurfactant yield and quality, particularly the carbon and nitrogen source, pH, aeration, inoculum quantity and incubation period.66 Chen Q, Bao M, Fan X, Liang S, Sun P. Rhamnolipids enhance marine oil spill bioremediation in laboratory system. Mar Pollut Bull. 2013;71:269-275.–88 Rahman PK, Pasiravi G, Auger V, Ali Z. Production of rhamnolipid biosurfactants by Pseudomonas aeruginosa DS10-129 in a microfluidic bioreactor. Biotechnol Appl Biochem. 2010;55:45-52. The present work aimed to isolate and identify a fungus with high biosurfactant production capacity from soil samples contaminated with hydrocarbons, to optimize its growth conditions in a low cost culture medium and to characterize the chemical structure of the biosurfactant molecule by nuclear magnetic resonance spectrometry techniques.
Material and methods
Fungus isolation
Microorganisms were isolated from 10 soil samples contaminated with hydrocarbons from mechanical workshops and fuel stations in the city of Santa Maria, RS, Brazil (29° 41′ 03″ S, 53° 48′ 25″ W). One gram of soil was added to a mineral medium containing type B diesel [with 6% (v/v) biodiesel] as the sole source of carbon and energy. The mineral medium had the following macronutrient composition (g L−1): 0.04 CaCl2·2H2O; 0.1 KH2PO4; 0.8 NaCl; 1.0 NH4Cl; 0.2 MgSO4·7H2O; 0.1 KCl; and micronutrients (mg L−1): 0.1 CoCl2·6H2O; 0.425 MnCl2·4H2O; 0.05 ZnCl2; 0.015 CuSO4·5H2O; 0:01 NiCl2·6H2O. The pH was adjusted to 5.8. The diesel oil (10 mL L−1) was filtered through a 0.22 µm membrane and mixed with medium that had been previously autoclaved at 121 °C for 20 min. The culture medium containing the diesel oil and the soil was incubated at 30 °C and 120 rpm for 7 days. An aliquot of 1 mL was transferred every seven days to the same sterile medium and incubated under the same conditions. After seven transfers, 1 mL of the resulting medium was diluted to 10−6 and a 0.1 mL aliquot of each dilution was added to Petri dishes containing PDA medium at pH 5.8. The plates were incubated for 96 h at 30 °C in a microbiological oven.
Selection of biosurfactant-producing fungus
From the 10 soil samples, five isolates were obtained with different colony morphologies. The fungi were purified from sequential replicates using PDA medium. To select the best biosurfactant producers, fungi were grown in five 250 mL Erlenmeyer flasks containing 50 mL of liquid culture medium with the following composition (g L−1): 30.0 glucose; 1.0 NH4NO3; 6.0 KH2PO4; 2.7 Na2HPO4;0.1 MgSO4·7H2O; 0.0012 CaCl2; 0.00165 FeSO4·7H2O; 0.0015 MnSO4·4H2O and 0.0022 Na-EDTA. The vials were incubated for 6 days at 120 rpm and 32 °C. Every two days, the culture medium samples were centrifuged at 10,000 rpm for 4 min, and the supernatant was collected for the measurement of the surface tension (mN m−1) and emulsification index. The surface tension was assessed by the pendant drop method on 10 drops of supernatant using a DSA 25E goniometer (KrüssGmbH, Hamburg, Germany). The emulsification index was evaluated by mixing 2 mL of the supernatant with 2 mL of filtered diesel oil in flat bottom test tubes and vortexing for 40 s. The emulsification index (% IE24) was determined as described by Nitschke and Pastore99 Nitschke N, Pastore GM. Production and properties of a surfactant obtained from Bacillus subtilis grown on cassava waste water. Bioresour Technol. 2006;97:336-341. by the division between the height of the emulsion layer and the total height of the solution, as measured by digital electronic calliper.
Fungus identification
The most promising fungus for the production of biosurfactants was coded as UFSM-BAS-01 and identified by partial sequencing of nuclear ribosomal DNA (nrDNA). The fungus was cultivated in potato-dextrose (PD) liquid medium, and its genomic DNA was extracted using a ZR MiniPrep® ZR fungi/bacteria kit (Zymo Research, Irvine, CA, USA). Elongation factor 1α (EF-1α) is often used to investigate the genus Fusarium.1010 Divakara ST, Santosh P, Aiyaz M, et al. Molecular identification and characterization of Fusarium spp. associated with sorghum seeds. J Sci Food Agric. 2014;94:1132-1139. An amplification reaction for the target fragment (∼700 bp) was performed following the methods of O’Donnell et al.1111 O’Donnell K, Kistler HC, Cigelnik E, Ploetz RC. Multiple evolutionary origins of the fungus causing Panama disease of banana: concordant evidence from nuclear and mitochondrial gene genealogies. Curr Issue. 1998;95:2044-2049. PCR products were purified using a GenElute PCR cleaning kit® (Sigma, St. Louis, USA) following the manufacturer's instructions. Sequencing of the samples was performed on the ABI PRISM 3100 Genetic Analyzer (Applied Biosystems, Foster City, CA, USA). The sequenced fragments were analysed using the 2.0.0b Staden package program1212 Staden R, Judge DP, Bonfield JK. Analysing sequences using the Staden package and EMBOSS. In: Krawetz SA, Womble DD, eds. Introduction to Bioinformatics. A Theoretical and Practical Approach. Totawa: Human Press Inc; 2003:393–410. to obtain the consensus sequence for EF-1α and BLASTn was performed. The sequence was deposited in GenBank.
The phylogenetic relationships of the samples were carried out by EF region sequences aligned in the program BioEdit version 7.2.51313 Hall TA. BioEdit: a user-friendly biological sequence alignment editor and analysis program for Windows 95/98/NT. Nucl Acids Symp Ser. 1999;41:95-98. and reconstructed based on MEGA 5.0 software1414 Tamura K, Peterson D, Peterson N, Stecher G, Nei M, Kumar S. MEGA5: molecular evolutionary genetics analysis using maximum likelihood, evolutionary distance, and maximum parsimony methods. Mol Biol Evol. 2011;28:2731-2739. with Maximum Likelihood (ML) analysis for a total of 1000 replicates for all reconstructions. The Tamura-Nei nucleotide substitution model with Gamma distribution was estimated using FindModel software.1515 Posada D. Model Test Server: a web-based tool for the statistical selection of models of nucleotide substitution online. Nucleic Acids Res. 2006;34:700-703. The sequences most related to that obtained in the present work were selected to construct a cladogram of the genus from the GenBank database (http://www.ncbi.nlm.nih.gov/genbank/), including Neonectria radicicola as the outgroup.
Optimization of biosurfactant production
A Plackett–Burman (PB) design was used to optimize biosurfactant production by the fungus in liquid medium with glucose as the only source of carbon and energy. The variables evaluated were pH (5.0–7.0), incubation time (2–7 days), temperature (28–37 °C), agitation (50–190 rpm) and amount of inoculum (1–3 disks of fungal mycelium). Table 1 shows the levels investigated for each variable in the PB design, comprising 12 experiments and three central points. Based on the interpretation of the results, a central composite rotational design (CCRD) was used for the significant PB variables: incubation time (2, 5, 7, 9 and 12 days), agitation (50, 90, 120, 150 and 190 rpm) and temperature (37, 39, 42, 45 and 47 °C).
Surface tension (ST) values of the cell-free culture medium (supernatant) after the growth of the fungus Fusarium fujikuroi UFSM-BAS-01 under different environmental conditions, combined through a Plackett-Burman (PB) design.
Biosurfactant extraction and purification
The fungus was cultured under the optimized conditions for 7 days. Cells were removed by centrifugation at 10,000 rpm for 4 min, and the supernatant was membrane filtered with a pore size of 0.22 µm. The cell-free supernatant was acidified to pH 4.0 using 6 M HCl and held overnight for precipitation.22 Joshi SJ, Geetha SJ, Desai AJ. Characterization and application of biosurfactant produced by Bacillus licheniformis R2. Appl Biochem Biotechnol. 2015;177:346-361. Then, 50 mL of the supernatant, 50 mL of hexane (to remove fatty acids) and 50 mL of chloroform were added followed by an equal volume of ethyl acetate:methanol (1:4) at room temperature. A compound in the form of transparent crystals (C1) was isolated upon extraction with ethyl acetate:methanol.
The remaining extract was basified with 4 M ammonium hydroxide and subjected to a new extraction procedure with the solvents chloroform, ethyl acetate and methanol (2:4). A powdery brown substance was obtained upon ethyl acetate and methanol extraction, which was subjected to a new extraction process with chloroform, ethyl acetate and n-butanol. In the fraction with n-butanol, a white crystalline (C2) compound with characteristics of sugars was isolated and subjected to nuclear magnetic resonance spectrometry, as described below.
NMR spectrometry and melting point
1H and 13C NMR spectra were recorded on a 600 MHz nuclear magnetic resonance spectrometer (Bruker, Magneto Ascend 600 Console Avance III HD, Germany). The (uncorrected) melting point values of the substances were determined on a digital melting point apparatus (Microchemistry, model MQAPF-301, Brazil).
GC-FID/GC–MS analysis
The samples were analysed by GC-FID and GC–MS. The autosampler used was an AOC-20is series injector (Shimadzu, Japan), the gas chromatograph coupled to the flame ionization detector (GC-FID) was a GC-2010 Plus (Shimadzu, Japan), and the gas chromatograph coupled to the mass spectrometer detector was a GCMS-QP2010 Ultra (Shimadzu, Japan). The composition was elucidated by comparison with an analytical standard of methylated fatty acid ester – FAME mix standard (Supelco, Bellefonte, PA, USA). Individual components were identified using their relative retention indices with the Wiley Registry of Mass Spectral Data (Palisade Corporation, Newfield, NY, USA).
Determination of the critical micellar concentration (CMC)
The cell-free supernatant was kept overnight at room temperature. After the addition of ammonium sulphate (40%, w/v), the supernatant was centrifuged at 10,000 rpm for 4 min. The precipitate was extracted twice with ice-cold acetone, and the crude biosurfactant was collected as dry powder after the evaporation of the acetone. The CMC was determined by adding concentrations of 2.5–150 mg L−1 of the crude biosurfactant in distilled water.22 Joshi SJ, Geetha SJ, Desai AJ. Characterization and application of biosurfactant produced by Bacillus licheniformis R2. Appl Biochem Biotechnol. 2015;177:346-361.
Results
Isolation, selection and identification of the fungus
From the 10 soil samples, five biosurfactant-producing isolates were obtained. In the first test, UFSM-BAS-01 was distinguished from other fungi by its higher biosurfactant production, its reduction of the surface tension of the culture medium from 72 to 52 mN m−1 and its higher emulsification index (24.4%).
This isolate was identified with the help of molecular tools. Using a comparative analysis by BLASTn in NCBI, the consensus sequence showed 100% similarity with two species: Fusarium fujikuroi1616 Nirenberg HI, O’Donnell K. New Fusarium species and combinations within Gibberella fujikuroi species complex. Mycologia. 1998;90:434-458. and Gibberella fujikuroi1717 Sawada K. Beitrage über Formosas-Pilze no. 14. Trans Nat Hist Soc Formosa. 1917;31:31-133. (Fig. 1). However, these are two names for the same fungus because F. fujikuroi is the anamorph phase and G. fugikuroi is the teleomorph phase of the same organism.1818 Jeon Y, Yu S, Lee YY, et al. Incidence, molecular characteristics and pathogenicity of Gibberella fujikuroi species complex associated with rice seeds from Asian countries. Mycobiology. 2013;41:225-233. Three subtypes were verified by ML analysis. F. fujikuroi and G. fujikuroi were grouped in the F. fujikuroi species complex,1919 Al-Hatmi AM, van Diepeningen AD, Curfs-Breuker I, de Hoog GS, Meis JF. Specific antifungal susceptibility profiles of opportunists in the Fusarium fujikuroi complex. J Antimicrob Chemother. 2015;70:1068-1071. and the other two clades identified were Fusarium oxysporum and Fusarium solani. Therefore, the elongation factor 1α (EF-1α) was highly informative and was able to identify the isolate as belonging to the G. fujikuroi species complex, with 99% bootstrap support. The consensus sequence was deposited in GenBank under accession number: KX574231.
Dendrogram of Fusarium fujikuroi (Gibberella fujikuroi) obtained from sequences of the elongation factor 1α (EF-1α). Maximum likelihood (ML) analysis was performed with 1000 replicates. Bootstrap values are in percentages. Neonectria radicicola was used as an outgroup.
Optimization of biosurfactant production
The optimization of the culture conditions for the production of a biosurfactant in mineral medium plus glucose was performed using a PB matrix (Table 1). The results were validated by analysis of variance (ANOVA) and the coefficient of determination (R 2) was 0.8071. The lowest surface tension value was obtained in experiment 7 (24.08 mN m−1). The temperature, agitation and incubation time variables significantly affected the surface tension (Table 2).
Linear regression coefficients for the reduction of surface tension after the growth of the fungus Fusarium fujikuroi UFSM-BAS-01 under different environmental conditions, combined through a Plackett-Burman (PB) design.
From the results obtained with the PB design, a central rotational compound (CCRD) was designed with 17 experiments to optimize the statistically significant variables from the PB matrix: incubation, temperature and agitation. In PB, the minimum value of ST was 24.08 mN m−1, while in CCRD the minimum measured value was 20.08 mN m−1, in conditions of 47 °C, 120 rpm for 7 days of incubation. The highest production of the biosurfactant by the fungus F. fujikuroi UFSM-BAS-01 occurs at thermophilic temperatures, even though the fungus was isolated under mesophilic conditions.
A Pareto graph (Fig. 2) represents the significant variables in the CCRD with a significance level of 90% (p < 0.1). Confirming previous observations with the PB matrix, lower ST occurred at higher temperatures and longer incubation periods. However, unlike PB, the agitation variable was not statistically significant, which also justified the performance of the CCRD.
Pareto plot with temperature (T), agitation (A) and incubation time (I), which demonstrated statistical significance (p < 0.1) in a central rotational compound design (CCRD) aimed at reducing the surface tension of the culture.
The following equation describes the behaviour of surface tension (ST) in response to temperature (T) and incubation time (I):
This model was validated by analysis of variance (ANOVA), and the coefficient of determination (R2) was 0.84953. A graphical representation of the optimization of biosurfactant production demonstrates that the lowest values of ST (dark green) were obtained at the positive axial point for incubation and at the central point for agitation (Fig. 3a). As shown in Fig. 3b, longer incubation periods and higher temperatures provided lower STs. As shown in Fig. 3c, the higher the temperature and the agitation, the lower the ST of the culture medium.
Contour plot of the reduction of surface tension of the growth medium by production of biosurfactants by Fusarium fujikuroi UFSM-BAS-01. (I) Incubation period; (A) agitation; (T) temperature.
Determination of the CMC
A satisfactory reduction of the ST of distilled water was observed with increasing amounts of the biosurfactant (Fig. 4). For biosurfactant concentrations above 30 mg L−1, the ST remained stable at approximately 27 mN m−1. Thus, the CMC of the biosurfactant produced by F. fujikuroi UFSM-BAS-01 was ∼30 mg L−1.
Surface tension (ST) of distilled water with the addition of increasing amounts of the biosurfactant produced by Fusarium fujikuroi UFSM-BAS-01.
Biosurfactant extraction, purification and identification
The solvent system formed by ethyl acetate and methanol provided a satisfactory extraction of the biosurfactant produced by F. fujikuroi UFSM-BAS-01. The biosurfactant was extracted three times, and the second fraction yielded a compound in the form of large white crystals characteristic of sugars, from which substance C2, identified as the disaccharide α,β-trehalose, was obtained.2020 Koto S, Inada S, Zen S. Upfield shift of CMR of anomeric carbons of 1,1′-linked glycopyranosylglycopyranosides. Chem Lett. 1980;1:403-406. Thus, the present study is the first report of the biosynthesis of an α,β-trehalose by F. fujikuroi, suggesting that the biosurfactant produced belongs to the class of trehalolipids.
Compounds identified by GC–MS for both methanol and hexane extracts demonstrate the presence of 9-octadecenamide (oleamide), an amide derived from oleic acid, a fatty acid (Table 3). In GC-FID analysis, the methanol extract did not show evidence of any molecule with a fatty acid structure when compared with the FAME mix standard chromatogram pattern. However, the hexane extract exhibited a few molecules that can be correlated with the fatty acid pattern showed in the FAME mix standard chromatogram, such as caproic acid (41.72%) and palmitoleic acid (12.72%). Unfortunately, other peaks that would appear in the same chromatogram were not clarified due to the lack of derivatisation of the fatty acids, which is a subject for future work.
Volatile compounds of the hexane and methanol extracts of the biosurfactant produced by Fusarium fujikuroi UFSM-BAS-01 and analysed by GC-MS.
Discussion
The fungus UFSM-BAS-01 can be considered an efficient producer of biosurfactant. According to the literature, STs in the range of 35–40 mN m−1 indicate a microorganism that is promising for biosurfactant production; values below 35 mN m−1 indicate that the microorganism can be considered an efficient biosurfactant producer.2121 Luna JM, Rufino RD, Albuquerque CD, Sarubbo LA, Campos-Takaki GM. Economic optimized medium for tensio-active agent production by Candida sphaerica UCP0995 and application in the removal of hydrophobic contaminant from sand. Int J Mol Sci. 2011;12:2463-2476. The surface tension of the biosurfactant produced by the fungus UFSM-BAS-01, after optimization of the culture medium (20.08 mN m−1), is lower than those found for Fusarium sp.2222 Qazi MA, Subhan M, Fatima N, Ali MI, Ahmed S. Role of biosurfactant produced by Fusarium sp. BS-8 in enhanced oil recovery (MEOR) through sand pack column. Int J Biosci Biochem Bioinform. 2013;3:598-604. and F. proliferatum,55 Bhardwaj G, Cameotra SS, Chopra HK. Isolation and purification of a new enamide biosurfactant from Fusarium proliferatum using rice-bran. RSC Adv. 2015;5:54783-54792. which were 32 and 36.6 mN m−1, respectively.
Isolate UFSM-BAS-01 was identified by molecular techniques as the fungus F. fujikuroi (Giberella fujikuroi). This fungus belongs to the species complex F. fujikuroi, formerly named the G. fujikuroi complex, which is a monophyletic group that largely corresponds to the outdated Liseola section but also accommodates species originally classified in other Fusarium sections.2323 Geiser DM, Lewis Irely ML, Hakiza G, Juba JH, Miller SA. Gibberella xylarioides (anamorph: Fusarium xylarioides), a causative agent of coffee wilt disease in Africa, is previously unrecognized member of the Gibberella fujikuroi complex. Mycologia. 2005;97:191-201.F. fujikuroi currently contains more than fifty species, which can be distinguished only by molecular parameters.88 Rahman PK, Pasiravi G, Auger V, Ali Z. Production of rhamnolipid biosurfactants by Pseudomonas aeruginosa DS10-129 in a microfluidic bioreactor. Biotechnol Appl Biochem. 2010;55:45-52.
The environmental variables that most influenced the production of the biosurfactant were temperature and incubation time. Several studies have demonstrated the positive influence of temperatures above 30 °C on the production of biosurfactants by microorganisms.2424 Mouafi FE, Elsoud MMA, Moharam ME. Optimization of biosurfactant production by Bacillus brevis using response surface methodology. Biotechnol Rep. 2016;9:31-37.–2626 Vaz DA, Gudiña EJ, Alameda EJ, Teixeira JA, Rodrigues LR. Performance of a biosurfactant produced by Bacillus subtilis strain isolated from crude oil samples as compared to commercial chemical surfactants. Colloids Surf B Biointerfaces. 2012;89:167-174. In our study, the biosurfactant with the lowest surface tension was produced with fermentation temperatures above 37 °C, although the fungus was isolated and initially cultivated at a temperature of 30 °C. Several authors cite 30 °C as the ideal temperature for the production of biosurfactants by fungal species.2222 Qazi MA, Subhan M, Fatima N, Ali MI, Ahmed S. Role of biosurfactant produced by Fusarium sp. BS-8 in enhanced oil recovery (MEOR) through sand pack column. Int J Biosci Biochem Bioinform. 2013;3:598-604.,2525 Qazi MA, Kanwal T, Jadoon M, Ahmed S, Fatima N. Isolation and characterization of a biosurfactant-producing Fusarium sp. BS-8. Biotechnol Prog. 2014;30:1065-1075. However, the production of biosurfactants at high temperatures, at which microbial metabolism is accelerated, may facilitate the use of these molecules on an industrial scale, including studies on biosurfactants produced from thermophilic microorganisms.
Higher incubation times resulted in higher biosurfactant yields by the fungus F. fujikuroi UFSM-BAS-01. Similar results were observed by El-Sheshtawy et al.2727 El-Sheshtawy HS, Aiad I, Osman ME, Kobisy AS. Production of biosurfactant from Bacillus licheniformis for microbial enhanced oil recovery and inhibition the growth of sulfate reducing bacteria. Egypt J Petrol. 2015;24:155-162. and Elazzazy et al.2828 Elazzazy AM, Abdelmoneim TS, Almaghrabi OA. Isolation and characterization of biosurfactant production under extreme environmental conditions by alkali-halo-thermophilic bacteria from Saudi Arabia. Saudi J Biol Sci. 2015;22:466-475. in the production of a biosurfactant by Bacillus licheniformis and Virgibacillus salarius, respectively. A significant reduction of the biosurfactant tension produced by F. fujikuroi (20.08 mN m−1) was observed after seven days of incubation. Biosurfactants are secondary metabolites that are normally produced during stationary phases, which is likely why the greatest reduction of surface tension occurred only after seven days of fungal growth. The production of biosurfactants can occur or be stimulated by cell growth under limiting conditions.2626 Vaz DA, Gudiña EJ, Alameda EJ, Teixeira JA, Rodrigues LR. Performance of a biosurfactant produced by Bacillus subtilis strain isolated from crude oil samples as compared to commercial chemical surfactants. Colloids Surf B Biointerfaces. 2012;89:167-174.
The agitation variable was statistically significant and had a negative influence on the production of the biosurfactant according to the Plackett–Burman design but was not significant in the central rotational compound design (CCRD). This was probably because the high agitation rates necessary to provide sufficient amounts of oxygen for cultures promote excessive foaming. This intense foaming decreases the yield of the process, as it removes part of the biomass and the substrate from the reaction medium, making it difficult to control the process.2929 Chen WC, Juang RS, Wei YH. Applications of a lipopeptide biosurfactant, surfactin produced by microorganisms. Biochem Eng J. 2015;103:158-169.
The ST and critical micellar concentration of the biosurfactant produced by F. fujikuroi UFSM-BAS-01 were similar to those of a biosurfactant produced by Bacillus subtilis YB7, which is capable of reducing the ST of distilled water from 70 to 30 mN m−1and has a CMC 40 mg L−1.3030 Arutchelvi JI, Bhaduri S, Uppara PV, Doble M. Mannosylerythritol lipids: review. J Ind Microbiol Biotechnol. 2008;35:1559-1570. In a similar study, Vaz et al.2626 Vaz DA, Gudiña EJ, Alameda EJ, Teixeira JA, Rodrigues LR. Performance of a biosurfactant produced by Bacillus subtilis strain isolated from crude oil samples as compared to commercial chemical surfactants. Colloids Surf B Biointerfaces. 2012;89:167-174. found a CMC of 40 mg L−1 for a biosurfactant produced by B. subtilis EG1. The CMC of the biosurfactant produced by F. fujikuroi UFSM-BAS-01 is similar to that of the synthetic surfactant Findet® 1214N/23 (21 mg L−1).3131 Rodríguez VB, Alameda EJ, Pequena AR, López AIG, Bailón-Moreno R, Aranda MC. Determination of average molecular weight of commercial surfactants: alkylpolyglucosides and fatty alcohol ethoxylates. J Surfactants Deterg. 2005;8:341-346. This indicates that the biosurfactant produced by this fungus has the potential for commercial use and that this fungus could be used for the production of biosurfactants on an industrial scale.
The use of a solvent system containing ethyl acetate and methanol enabled the extraction of a disaccharide identified as trehalose.2020 Koto S, Inada S, Zen S. Upfield shift of CMR of anomeric carbons of 1,1′-linked glycopyranosylglycopyranosides. Chem Lett. 1980;1:403-406. Until recently, the only form of trehalose that occurred naturally was α-d-glucopyranosyl-(1→1)-α-d-glucopyranoside, with three possible isomers (α,α-; α,β-; and β,β-). In our study, the fungus F. fujikuroi UFSM-BAS-01 produced an α,β-trehalose (neo-trehalose), which was recently biosynthesized by other fungi.3232 Morandini LM, Neto AT, Pedroso M, et al. Lanostane-type triterpenes from the fungal endophyte Scleroderma UFSMSc1 (Persoon) Fries. Bioorg Med Chem Lett. 2016;16:1173-1176. Thus, the present study is the first report of the biosynthesis of an α,β-trehalose by F. fujikuroi, suggesting that the biosurfactant produced belongs to the class of trehalolipids. Different types of trehalose-containing glycolipids belonging to the group of mycolates are known to be produced by bacteria such as Mycobacterium, Rhodococcus, Arthrobacter, Nocardia and Gordonia.3333 Lang S, Philp JC. Surface-active lipids in rhodococci. Antonie Van Leeuwenhoek Int J Gen. 1998;74:59-70. Trehalolipids have attracted interest for their potential applications in several areas due to their ability to decrease interfacial tension and increase the pseudosolubility of hydrophobic compounds.3434 Franzetti A, Gandolfi I, Bestetti G, Smyth TJP, Banat IM. Production and applications of trehalose lipid biosurfactants. Eur J Lipid Sci Technol. 2010;12:617-627.
GC–MS analysis of methanol and hexane extracts of the biosurfactant produced by F. fujikuroi identified the presence of the lipophilic compound 9-octadecenamide, an oleamide. This lipophilic compound has many biological activities.3535 Cheng M, Ker Y, Yu T, Lin Y, Robert YP, Peng C. Chemical synthesis of 9(Z)-octadecenamide and its hypolipidemic effect: a bioactive agent found in the essential oil of mountain celery seeds. J Agric Food Chem. 2010;58:1502-1508. Premjanu and Jaynthy3636 Premjanu N, Jaynthy C. Identification and characterization of antimicrobial metabolite from an endophytic fungus, Colletotrichum gloeosporioides isolated from Lannea corammendalica. Int J ChemTech Res. 2015;7:369-374. found oleamide to be the major compound in an ethyl acetate extract of Colletotricum gloeosporioides fungal biomass. GC-FID hexane extract analysis showed several molecules that can be correlated with a fatty acid pattern, such as caprioic acid. However, additional analyses such as MALDI-TOF and FITR are needed to confirm further details about the structure of the biosurfactant.
Conclusion
-
- The fungus F. fujikuroi UFSM-BAS-01 isolated from soil samples contaminated with hydrocarbons is an efficient biosurfactant producer;
-
- The production of biosurfactants by F. fujikuroi UFSM-BAS-01 is significantly increased under optimized culture conditions;
-
- The preliminary identification of the structure of the biosurfactant demonstrates the presence of an α,β-trehalose, suggesting that the biosurfactant belongs to the class of trehalolipids.
Acknowledgements
The authors thank the Foundation for Research Support of the State of Rio Grande do Sul (FAPERGS), National Council of Technological and Scientific Development (CNPq) and Coordination for the Improvement of Higher Level or Education Personnel (CAPES) for providing scholarships and financial support of this work.
References
-
1Cameotra SS, Makkar RS, Kaur J, Mehta SK. Synthesis of biosurfactants and their advantages to microorganisms and mankind. Adv Exp Med Biol 2010;672:261-280.
-
2Joshi SJ, Geetha SJ, Desai AJ. Characterization and application of biosurfactant produced by Bacillus licheniformis R2. Appl Biochem Biotechnol 2015;177:346-361.
-
3Jain RM, Mody K, Joshi N, Mishra A, Jha B. Production and structural characterization of biosurfactant produced by an alkaliphilic bacterium, Klebsiella sp: evaluation of different carbon sources. Colloids Surf B Biointerfaces 2013;108:199-204.
-
4Joice PA, Parthasarathi R. Optimization of biosurfactant production from Pseudomonas aeruginosa PBSC1. Int J Curr Microbiol Appl Sci 2014;3:140-151.
-
5Bhardwaj G, Cameotra SS, Chopra HK. Isolation and purification of a new enamide biosurfactant from Fusarium proliferatum using rice-bran. RSC Adv 2015;5:54783-54792.
-
6Chen Q, Bao M, Fan X, Liang S, Sun P. Rhamnolipids enhance marine oil spill bioremediation in laboratory system. Mar Pollut Bull 2013;71:269-275.
-
7Mishra U, Paul S, Bandyopadhaya M. Removal of zinc ions from wastewater using industrial waste sludge: a novel approach. Environ Program Sustain Energy 2012;32:576-586.
-
8Rahman PK, Pasiravi G, Auger V, Ali Z. Production of rhamnolipid biosurfactants by Pseudomonas aeruginosa DS10-129 in a microfluidic bioreactor. Biotechnol Appl Biochem 2010;55:45-52.
-
9Nitschke N, Pastore GM. Production and properties of a surfactant obtained from Bacillus subtilis grown on cassava waste water. Bioresour Technol 2006;97:336-341.
-
10Divakara ST, Santosh P, Aiyaz M, et al. Molecular identification and characterization of Fusarium spp. associated with sorghum seeds. J Sci Food Agric 2014;94:1132-1139.
-
11O’Donnell K, Kistler HC, Cigelnik E, Ploetz RC. Multiple evolutionary origins of the fungus causing Panama disease of banana: concordant evidence from nuclear and mitochondrial gene genealogies. Curr Issue 1998;95:2044-2049.
-
12Staden R, Judge DP, Bonfield JK. Analysing sequences using the Staden package and EMBOSS. In: Krawetz SA, Womble DD, eds. Introduction to Bioinformatics. A Theoretical and Practical Approach Totawa: Human Press Inc; 2003:393–410.
-
13Hall TA. BioEdit: a user-friendly biological sequence alignment editor and analysis program for Windows 95/98/NT. Nucl Acids Symp Ser 1999;41:95-98.
-
14Tamura K, Peterson D, Peterson N, Stecher G, Nei M, Kumar S. MEGA5: molecular evolutionary genetics analysis using maximum likelihood, evolutionary distance, and maximum parsimony methods. Mol Biol Evol 2011;28:2731-2739.
-
15Posada D. Model Test Server: a web-based tool for the statistical selection of models of nucleotide substitution online. Nucleic Acids Res 2006;34:700-703.
-
16Nirenberg HI, O’Donnell K. New Fusarium species and combinations within Gibberella fujikuroi species complex. Mycologia 1998;90:434-458.
-
17Sawada K. Beitrage über Formosas-Pilze no. 14. Trans Nat Hist Soc Formosa 1917;31:31-133.
-
18Jeon Y, Yu S, Lee YY, et al. Incidence, molecular characteristics and pathogenicity of Gibberella fujikuroi species complex associated with rice seeds from Asian countries. Mycobiology 2013;41:225-233.
-
19Al-Hatmi AM, van Diepeningen AD, Curfs-Breuker I, de Hoog GS, Meis JF. Specific antifungal susceptibility profiles of opportunists in the Fusarium fujikuroi complex. J Antimicrob Chemother 2015;70:1068-1071.
-
20Koto S, Inada S, Zen S. Upfield shift of CMR of anomeric carbons of 1,1′-linked glycopyranosylglycopyranosides. Chem Lett 1980;1:403-406.
-
21Luna JM, Rufino RD, Albuquerque CD, Sarubbo LA, Campos-Takaki GM. Economic optimized medium for tensio-active agent production by Candida sphaerica UCP0995 and application in the removal of hydrophobic contaminant from sand. Int J Mol Sci 2011;12:2463-2476.
-
22Qazi MA, Subhan M, Fatima N, Ali MI, Ahmed S. Role of biosurfactant produced by Fusarium sp. BS-8 in enhanced oil recovery (MEOR) through sand pack column. Int J Biosci Biochem Bioinform 2013;3:598-604.
-
23Geiser DM, Lewis Irely ML, Hakiza G, Juba JH, Miller SA. Gibberella xylarioides (anamorph: Fusarium xylarioides), a causative agent of coffee wilt disease in Africa, is previously unrecognized member of the Gibberella fujikuroi complex. Mycologia 2005;97:191-201.
-
24Mouafi FE, Elsoud MMA, Moharam ME. Optimization of biosurfactant production by Bacillus brevis using response surface methodology. Biotechnol Rep 2016;9:31-37.
-
25Qazi MA, Kanwal T, Jadoon M, Ahmed S, Fatima N. Isolation and characterization of a biosurfactant-producing Fusarium sp. BS-8. Biotechnol Prog 2014;30:1065-1075.
-
26Vaz DA, Gudiña EJ, Alameda EJ, Teixeira JA, Rodrigues LR. Performance of a biosurfactant produced by Bacillus subtilis strain isolated from crude oil samples as compared to commercial chemical surfactants. Colloids Surf B Biointerfaces 2012;89:167-174.
-
27El-Sheshtawy HS, Aiad I, Osman ME, Kobisy AS. Production of biosurfactant from Bacillus licheniformis for microbial enhanced oil recovery and inhibition the growth of sulfate reducing bacteria. Egypt J Petrol 2015;24:155-162.
-
28Elazzazy AM, Abdelmoneim TS, Almaghrabi OA. Isolation and characterization of biosurfactant production under extreme environmental conditions by alkali-halo-thermophilic bacteria from Saudi Arabia. Saudi J Biol Sci 2015;22:466-475.
-
29Chen WC, Juang RS, Wei YH. Applications of a lipopeptide biosurfactant, surfactin produced by microorganisms. Biochem Eng J 2015;103:158-169.
-
30Arutchelvi JI, Bhaduri S, Uppara PV, Doble M. Mannosylerythritol lipids: review. J Ind Microbiol Biotechnol 2008;35:1559-1570.
-
31Rodríguez VB, Alameda EJ, Pequena AR, López AIG, Bailón-Moreno R, Aranda MC. Determination of average molecular weight of commercial surfactants: alkylpolyglucosides and fatty alcohol ethoxylates. J Surfactants Deterg 2005;8:341-346.
-
32Morandini LM, Neto AT, Pedroso M, et al. Lanostane-type triterpenes from the fungal endophyte Scleroderma UFSMSc1 (Persoon) Fries. Bioorg Med Chem Lett 2016;16:1173-1176.
-
33Lang S, Philp JC. Surface-active lipids in rhodococci. Antonie Van Leeuwenhoek Int J Gen 1998;74:59-70.
-
34Franzetti A, Gandolfi I, Bestetti G, Smyth TJP, Banat IM. Production and applications of trehalose lipid biosurfactants. Eur J Lipid Sci Technol 2010;12:617-627.
-
35Cheng M, Ker Y, Yu T, Lin Y, Robert YP, Peng C. Chemical synthesis of 9(Z)-octadecenamide and its hypolipidemic effect: a bioactive agent found in the essential oil of mountain celery seeds. J Agric Food Chem 2010;58:1502-1508.
-
36Premjanu N, Jaynthy C. Identification and characterization of antimicrobial metabolite from an endophytic fungus, Colletotrichum gloeosporioides isolated from Lannea corammendalica Int J ChemTech Res 2015;7:369-374.
Edited by
Publication Dates
-
Publication in this collection
Nov 2018
History
-
Received
10 Oct 2017 -
Accepted
3 Apr 2018 -
Published
24 Apr 2018