SciELO - Scientific Electronic Library Online

vol.29 issue2Synthesis of a biocopolymer carrageenan-g-poly(AAm-co-IA)/ montmorilonite superabsorbent hydrogel compositeAlkali-free method of hide preparation for tanning author indexsubject indexarticles search
Home Pagealphabetic serial listing  

Services on Demand




Related links


Brazilian Journal of Chemical Engineering

Print version ISSN 0104-6632

Braz. J. Chem. Eng. vol.29 no.2 São Paulo Apr./June 2012 



Polymeric membranes containing silver salts for propylene/propane separation



L. D. Pollo; L. T. Duarte; M. Anacleto; A. C. Habert; C. P. Borges

Universidade Federal do Rio de Janeiro, Programa de Engenharia Química, COPPE, Phone: + (55) (21) 2562-8351, Fax: + (55) (21) 2562-8300, Cidade Universitária, Ilha do Fundão, CEP 21941-972, Rio de Janeiro - RJ, Brasil. E-mail:




The separation of olefin/paraffin mixtures is one of the most important processes of the chemical industry. This separation is typically carried out by distillation, which is an energy and capital intensive process. One promising alternative is the use of facilitated transport membranes, which contain specific carrier agents in the polymer matrix that interact reversibly with the double bond in the olefin molecule, promoting the simultaneous increase of its permeability and selectivity. In this study, polyurethane (PU) membranes were prepared using two different silver salts (triflate and hexafluorantimonate). The membranes were structurally characterized and their performance for the separation of propylene/propane mixtures was evaluated. The results of the characterization analyses indicated that the triflate salt was the most efficient carrier agent. The membranes containing this salt showed the best performance, reaching an ideal selectivity of 10 and propylene permeability of 188 Barrer.

Keywords: Gas separation; Propylene facilitated transport; Silver ions; Polyurethane.




In the petrochemical industry, propylene is an important industrial feedstock, being used as a raw material for products such as polypropylene, acrylonitrile, propylene oxide among others. The separation of propylene/propane mixtures is highly energy and capital intensive and is typically carried out by distillation (Humphrey and Seibert, 1992; Eldridge, 1993). As propylene and propane have similar molecular sizes and relative volatilities, distillation columns with more than 200 plates and high reflux ratios are needed to achieve efficient separation.

The use of membrane separation as an alternative approach for propylene/propane separation has been investigated and reported in recent years (Ferraz et al., 2007; Burns and Koros, 2003; Kang et al., 2004; Liu et al., 2004). Due to the similar physical and chemical properties and molecular size of propane and propylene, conventional polymeric membranes are not competitive for the separation of these mixtures based only on the sorption/diffusion mechanism. One alternative that has been sought is a simultaneous increase of permeability and selectivity by incorporating specific agents in the polymer matrix that interact reversibly with propylene but not with propane. In this way, propylene permeation would occur by a facilitated transport mechanism.

Transition metal cations are used as carriers for propylene transport due to their capacity to react specifically and reversibly with unsaturated hydrocarbons. The interaction between the double bond of the olefin and the transition metal cations follows the model of π -complexation and is based on molecular orbital theory. The complexation reaction involves forming a sigma-type donation bond from the filled π -orbitals of the olefin to the empty s-orbital of the metal, followed by a π back-donation bond from the filled d-orbitals of the metal to the empty π *-orbital of the olefin. The stability of the olefin-metal complex depends on electronic and steric factors, such as the metal valence and the presence of electron-withdrawing groups on the olefin carbons (Cotton et al., 1995). The bond strength between the cations and the olefin must be weak enough to allow release and transportation of the olefin towards the permeate side.

The facilitated transport membranes for propylene/propane separation are mainly achieved with silver and copper ions as carrier agents. This is because the complexes that silver and copper ions form with olefins have lower stability in comparison with the complexes formed with other transition metals (Kim et al., 2000; Ho et al., 1998; Baker, 2002).

The carrier can be mobile or fixed. In the first case, the membrane is effectively a liquid in which the carrier is dissolved. The carrier-propylene complex is formed at the feed/membrane interface and then diffuses across the membrane to the permeate side, where the olefin is released from the membrane phase. The free carrier diffuses back to the feed/membrane interface, repeating the process. These membranes, however, present limitations because the loss of the carrier may occur either by evaporation of the solvent or by washing out of the support membrane under an applied feed pressure (Kim et al., 2005).

In the fixed-site carrier membranes, the carrier is chemically or physically bound to the polymer matrix, which restricts its mobility. According to Cussler et al. (1989), the transport mechanism is based on jumps or "hops" of the olefin from one fixed carrier to the other. If the interaction strength between the cation and the anion or the electron donor groups of the polymer is very high, the metallic cation will not be readily available to interact with the olefin. In addition, the polymer is required to have low barriers to bond rotation to provide sufficient segmental motion of the chains, which is better achieved by using an elastomeric polymer (Yoon et al., 2000; Kim et al., 2004; Duarte et al., 2005).

The objectives of this study are to investigate the effects of adding silver salts to PU membranes and to evaluate their performance for the separation of propylene/propane mixtures. PU was chosen as the polymer matrix not only due to its high segmental mobility, but also because it contains functional groups that can coordinate with silver ions. Two different kinds of silver salts - silver triflate (AgCF3SO3) and silver hexafluorantimonate (AgSbF6) - were selected as carrier agents. The membranes were produced with 20% (w/w) of the silver salt and further characterized by FT-IR spectroscopy and X-ray diffraction.

Conductivity experiments under argon were carried out to evaluate the strength of the interactions between the ions and the PU chains, whilst conductivity experiments under propylene were used for the characterization of the interactions between the ions, the PU chains and the propylene molecules. The interaction between the propylene molecules and the silver ions was characterized by TD analysis. Permeation tests with pure gas (propane and propylene) were performed at room temperature to evaluate the permeability and selectivity of the facilitated transport membranes.




Polyurethane was purchased from BASF and used as received. Silver triflate, silver hexafluorantimonate and tetrahydrofuran (THF) solvent (synthesis grade) were purchased from Aldrich Chemical Co. and used without purification. The propylene and propane gases (>99.5% purity) were acquired from Linde and used as received.

Membrane Preparation

To prepare dense films, the polymer was previously dried in an oven at 60ºC for 24 hours and then dissolved in THF solvent. The silver salt was then added to the polymer solution, which was further stirred for approximately 5 h and then immediately cast over a flat Teflon@ plate. This entire procedure was carried out within a dark chamber constantly purged with nitrogen, at room temperature, in order to prevent the silver ion photo-reduction. The solvent was allowed to evaporate for 48 hours and then dried in a vacuum oven for at least 8 hours before the permeation and characterization tests. The films presented a thickness of 200 µm and silver salt concentrations (v/v) of 14% (AgCF3SO3) and 8% (AgSbF6).

Membrane Characterization

The dense silver salt-PU films were characterized by X-Ray Diffraction (XRD), Fourier Transform Infra Red (FTIR) and Thermal Desorption (TD). These analyses were carried out in order to investigate the nature of the membrane structure and the propylene facilitated transport behavior.

X-Ray Diffraction Analysis

The crystalline structure of the PU membranes was determined by XRD using a Rigaku Miniflex diffractometer with monochromatic Cu Kα radiation with a wavelength of 1.54 Ε.

Fourier Transform Infra Red Spectroscopic Analysis

A FTIR spectrophotometer (PerkinElmer Spectrum 100) with attenuated total reflection device was used to investigate the chemical structure of the polymeric films with and without silver ions. The spectra were recorded by taking 16 scans at a resolution of 4 cm–1.

Thermal Desorption Analysis

Thermal desorption (TD) analysis was performed in a chemisorption equipment including a quartz glass tube to load the sample and a gas flow meter (Matheson 8274). The gases desorbed were monitored by a quadrupole mass spectrometer (QMS 200 - Prisma). In the TD experiments, 0.6 g of membrane was put into the quartz reactor and placed in an oven with controlled temperature. The sample was saturated with the gas, propane or propylene, at 25ºC for thirty minutes. After gas exposure, the sample was purged with helium gas flow until equilibrium and the propane or propylene desorption experiments were run by increasing the temperature from 25ºC to 60ºC at a heating rate of 10ºC/min under an atmosphere of helium. The isothermal level of 60ºC was maintained until complete desorption of the gas, the evolution of the signal of the specific mass fragment being monitored by mass spectrometer.

Ionic Conductivity Measurements

Conductivity data were obtained using AC impedance measurements carried out with a Solatron 1255 frequency response analyzer and 1187 electrochemical interface. A polarizing potential of 20 mV was fixed and data were collected over the frequency range of 1 Hz – 400,000 Hz. The PU films were sandwiched between two stainless steel plates in a two-electrode cell which was located within an argon filled stainless steel chamber. The chamber was placed in a thermostatic bath in order to control the temperature of the cells. The conductivity values were estimated according to Bruce (1989).

Gas Permeation Test

The experimental set-up used for the gas permeation tests is illustrated in Figure 1. The experiments were performed with pure gases (propane and propylene) at room temperature.

The permeation cell was hermetically closed with Teflon@ o-rings and screws. In order to clean the permeation system, the permeate and feed lines were evacuated with a vacuum pump, then the feed gas was introduced at 2 bar in the membrane cell. Atmospheric pressure was maintained on the permeate side to establish a pressure difference of about 1 bar. This procedure was carried out for each gas (propane and propylene) separately. The gas permeance measurement was carried out by the acquisition of the signal of current density. A calibration curve allowed the conversion of the current density signal to pressure values. The pure gas permeance was estimated from the equation below:

where (P/l) is the membrane permeance expressed in Barrer (1 Barrer = 1x10-10 cm3(STP) cm/(cm2 s cmHg); dp/dt is the pressure rate in the permeate (cmHg/s); Δp is the pressure difference across the membrane (cmHg); A is the effective membrane area (cm2); p(STP) e T(STP) are the standard (STP) pressure and temperature, respectively; Vs is the volume of the permeation system (cm3); T(RT) is the room temperature.

The membrane ideal selectivity, (α C3H6/C3H8), has been calculated in terms of ratio between the gas permeability coefficients of the pure gases according to the following equation:



X-Ray Diffraction

XRD results of PU and of the 20% (w/w) of PU/AgCF3SO3 and PU/AgSbF6 membranes are presented in Figure 2. The PU spectrum (A) shows a rather broad band centered near a diffraction angle (2θ) of 20º, which is due to the hard segment of PU (Cho and So, 2006). This profile indicates that the polymer is completely amorphous. The spectra of PU containing 20% (w/w) of silver salt (B and C) are very similar to the XRD spectrum of the PU membrane without silver salt. This behavior suggests that both AgCF3SO3 and AgSbF6 are well dispersed in the PU matrix at this concentration. The good dispersion of the silver salts may be attributed to the specific interaction originated from the coordination between electron donor groups in PU chains and silver ions, as reported in previous studies (Wen et al., 2001; Kim et al., 2002).



Infrared Spectroscopy

FTIR spectra of the PU membranes and PU membranes containing 20% (w/w) AgCF3SO3 were analyzed to identify the changes in molecular interactions between the heteroatoms in the PU polymer and the Ag+ ions. In the PU host matrix, the main regions of interest are: i) the N-H region, where the –NH absorption peak is observed at 3328 cm–1 due to the hydrogen bonded –NH in the urethane linkage; ii) the carbonyl region which is defined by two carbonyl stretching vibrations, the non hydrogen-bonded C=O (1726 cm-1), and the hydrogen-bonded C=O (1700 cm-1); iii) and the ester C(O)–O stretching (1166 cm-1), as reported by Ferry et al. (1996). The carbonyl peaks around 1700 cm–1 are unresolved due to the superposition of peaks from urethanes and ester-polyols (Dan et al., 2006). The solvation of the salt in polyurethanes involves coordination of the cation to the electron donor groups of the polymer network, promoting changes in the stretching vibrations. Figure 3 shows the FTIR spectra of PU and PU containing silver triflate. Three regions were specifically investigated: the symmetric stretching mode of the triflate anion (1025 and 634 cm-1), the hydrogen-bonded NH band (3328 cm-1), and the ester C(O)–O stretch (1166 cm-1), as shown in Figures 4, 5 and 6, respectively (Suthanthiraraj et al., 2009).









The triflate anion shows a vibrational spectrum with a frequency at ~1025 and 634 cm-1, which is very sensitive to its state of coordination, and the changes in SO3 stretching are associated with ion–ion interactions. The ion pairs (Ag+ - CF3SO3-) exhibit vibrational frequencies at ~ 1038 and ~ 833 cm-1, which is not observed in the PU/ AgCF3SO3 spectrum illustrated in Figure 4. It is possible therefore to confirm that the silver salt is well dissociated by the polymer and that the triflate anions are free (Dan et al., 2006). This corroborates the observations previously made for the XRD results.

In Figure 5, the band position of hydrogen bonded -NH shows slight shift from 3328 cm–1 for PU to 3323 cm–1 for PU/ AgCF3SO3. This feature, a band shift to lower wavenumbers, is due to the coordination of silver ion with the hydrogen bonded –NH group. The hydrogen of the NH group can be bound with oxygen of the carbonyl group or the ester group of the polymer matrix. A close examination also suggests changes in the ester oxygen, which showed a slight shift from 1166 cm–1 for PU to 1160 cm–1 for PU/ AgCF3SO3, as shown in Figure 6.

Thermal Desorption

TD analyses were undertaken for PU membranes containing 20% (w/w) AgCF3SO3 and AgSbF6 to investigate the silver ion influence on the sorption of propylene. The propane TD did not show any desorption profile. The effect of the interaction between silver ions and propylene in the PU membranes is presented in Figure 7. Pure PU (C profile) exhibits no propylene desorption in the time period analyzed. In the presence of silver ions (A and B profiles), propylene desorption started at 60ºC, approximately. These results are clear indications of the π -complexation of silver ion with the propylene molecule and the potential ability of these PU/Ag systems to be used as facilitated transport membranes for olefin/paraffin separation.



The TD characterization allows the determination of the amount of propylene that was complexed with the silver active sites in the polymer and the comparison of different ions, counter-ions and polymers. The results show that both silver salts were efficient in the coordination with propylene, with very close estimated ratios molC3H6/molAg, of the order of 0.2. This quantitative approach seems to be quite new and indicates that TD is a promising and versatile technique.

Ionic Conductivity Analysis

Figure 8 presents the concentration dependence of the ionic conductivity measured in propylene and argon atmospheres for the membranes containing AgCF3SO3. As can be observed, the ionic conductivity in propylene is higher than the values obtained for experiments carried out in argon, and increases with salt concentration (Duarte et al., 2005). These results support the evidence that, in the presence of propylene, Ag+ cations gain higher mobility than in the presence of argon. This can be attributed to the complexation between propylene molecules and Ag+, which weakens the Ag+-PU interactions.



Furthermore, under a propylene atmosphere, the PU membranes containing AgCF3SO3 show higher conductivity values than the ones with AgSbF6, as can be seen in Figure 9. This is likely related to the larger size of the triflate anion, which is able to dissociate more easily from Ag+ cations than SbF6-. Therefore, AgCF3SO3 is probably more suitable to be used as a carrier in membranes for propylene/ propane separation than AgSbF6.



Permeation Tests

The gas permeance measurements were undertaken at a feed pressure and temperature of 2 bar and 25ºC, respectively. The results of these experiments are summarized in Table 1, where it can be observed that the presence of the silver salt in PU membranes promotes an increase in the ideal selectivity. The PU/ AgCF3SO3 membrane exhibits both propylene permeability and selectivity higher than the PU/ AgSbF6 membrane. This is likely to be associated with the size of the counter-ion and is in line with the results obtained in the conductivity experiments. In fact, (CF3SO3)- is a larger anion than (SbF6)-, and AgCF3SO3 exhibits a lower lattice energy, which leads to a weak interaction between silver ion and its counter-ion and facilitates the solvation of silver in the polymer. In this way, the silver ions in the PU/AgCF3SO3 membranes are more available for interaction with the propylene molecules than the silver ions in the PU/AgSbF6 membranes.




Silver salts are well solvated by the PU matrix in the PU/ AgCF3SO3 and PU/ AgSbF6 membranes, since no crystalline structure peaks are observed in the related XRD spectra. The FTIR results showed that the coordination of silver ions occurs with the ester oxygen of the polyurethane, verified through the wavenumber shifts of hydrogen bonded –NH and ester oxygen regions. Another evidence of complete solvation of the silver salt in the polymeric matrix was the presence of the free triflate ion bands and the non-occurrence of ion pair bands in the FTIR spectrum of PU/AgCF3SO3.

The TD characterization method was successfully used to validate the complexation between silver ions and propylene molecules. Ionic conductivity and permeance tests showed that the triflate salt is the most efficient carrier agent for facilitated propylene transport, as the larger anion size leaves the silver ion more available for complexation with propylene. The PU membranes containing the silver triflate salt showed the best performance for the separation of propylene/propane mixtures, reaching an ideal selectivity of 10 and propylene permeability of 188 Barrer.



The authors acknowledge CAPES and FAPERJ for financial support.



Baker, R. W., Future directions of membrane gas separation technology. Ind. Eng. Chem. Res., 41, 1393-1411 (2002).         [ Links ]

Bruce, P. G., In: MacCallum, J. R. and Vicent, C. A., Polymer electrolyte reviews–1, Elsevier Science Publishers, London (1989).         [ Links ]

Burns, R. L. and Koros, W. J., Defining the challenges for C3H6/C3H8 separation using polymeric membranes. J. Membr. Sci., 211, 299-309 (2003).         [ Links ]

Cho, J. W., So, J. H., Polyurethane–silver fibers prepared by infiltration and reduction of silver nitrate. Mater. Lett., 60, 2653-2656 (2006).         [ Links ]

Cotton, F. A., Wilkinson, G. and Gaus, P. L., Basic inorganic chemistry. John Wiley & Sons, Inc., New York (1995).         [ Links ]

Cussler, E. L., Aris, R. and Brown, A., On the limits of facilitated diffusion. J. Membr. Sci., 43, 149-164 (1989).         [ Links ]

Dan, C. H., Lee, M. H., Kim, Y. D., Min, B. H. and Kim, J. H., Effect of clay modifiers on the morphology and physical properties of thermoplastic polyurethane/clay nanocomposites. Polymer, 47, 6718-6730 (2006).         [ Links ]

Duarte, L. T., Habert, A. C. and Borges, C. P., Polyurethane facilitated transport membranes containing Ag(I) for propane/propylene separation. 5th CITEM, Ibero-American Congress on Membrane Science and Technology, Valencia, Spain (2005).         [ Links ]

Eldridge, R. B., Olefin/paraffin separation technology: A review. Ind. Eng. Chem. Res., 32, 2208-2212 (1993).         [ Links ]

Ferraz, H. C., Duarte, L. T., Di Luccio, M., Alves, T. L. M., Habert, A. C., Borges, C. P., Recent achievements in facilitated transport membranes for separation processes. Braz. J. Chem. Eng., 24, 101-118 (2007).         [ Links ]

Ferry, A., Jacobsson, P., van Heumen, J. D. and Stevens, J. R., Raman, infra-red and DSC studies of lithium coordination in a thermoplastic polyurethane. Polymer, 37, 737-744 (1996).         [ Links ]

Humphrey, J. L. and Seibert, A. F., Cover story: new dimensions in distillation. Chem. Eng., 99, 86-98 (1992).         [ Links ]

Ho, W. S., Doyle, G. D., Savage, D. W. and Pruett, R. L., Olefin separation via complexation with cuprous diketonate. Ind. Eng. Chem. Res., 27, 334-337 (1988).         [ Links ]

Kang, S. W., Kim, J. H., Won, K., Kim, H. S. and Kang, Y. S., Highly stabilized silver polymer electrolytes and their application to facilitated olefin transport membranes. J. Membr. Sci., 236, 163-169 (2004).         [ Links ]

Kim, J. H., Park, S. M., Won, J. and Kang, Y. S., Unusual separation property of propylene/ propane mixtures through polymer/silver complex membranes containing mixed salts. J. Membr. Sci., 248 171-176 (2005).         [ Links ]

Kim, J. H., Won, J. and Kang, Y. S., Olefin-induced dissolution of silver salts physically dispersed in inert polymers and their application to olefin/paraffin separation. J. Membr. Sci., 241, 403-407 (2004).         [ Links ]

Kim, J. H., Min, B. R., Kim, C. K., Won, J. and Kang, Y. S., Spectroscopic interpretation of silver ion complexation in silver polymer electrolytes. J. Phys. Chem., B, 106, 2786-2790 (2002).         [ Links ]

Kim, Y. H., Ryu, J. H., Bae, J. Y., Kang, Y. S. and Kim, H. S., Reactive polymer membranes containing cuprous complexes in olefin/paraffin separation. Chem. Commun., 195-196 (2000).         [ Links ]

Liu, L., Feng, X. and Chakma, A., Unusual behavior of poly(ethylene oxide)/AgBF4 polymer electrolyte membranes for olefin/paraffin separation. Sep. Purif. Technol., 38, 255-263 (2004).         [ Links ]

Suthanthiraraj, S. A., Kumar, R. and Paul, B. J., FT-IR spectroscopic investigation of ionic interactions in PPG 4000: AgCF(3)SO(3) polymer electrolyte. Spectrochim. Acta, Part A, 71, 2012-2015 (2009).         [ Links ]

Wen, T. C., Kuo, H. H. and Gopalan, A., The influence of lithium ions on molecular interaction and conductivity of composite electrolyte consisting of TPU and PAN. Solid State Ionics, 147, 171-180 (2001).         [ Links ]

Yoon, Y., Won, J. and Kang, Y. S., Polymer electrolyte membranes containing silver ion for facilitated olefin transport. Macromolecule, 33, 3185-3186 (2000).         [ Links ]



(Submitted: September 14, 2011 ; Revised: October 24, 2011 ; Accepted: November 4, 2011)

Creative Commons License All the contents of this journal, except where otherwise noted, is licensed under a Creative Commons Attribution License