Accessibility / Report Error

Effect of the Fuels Glycine, Urea and Citric Acid on Synthesis of the Ceramic Pigment ZnCr2O4 by Solution Combustion

Abstract

In this study, ceramic nanopigment ZnCr2O4 was prepared by solution combustion using glycine, urea and citric acid as fuels. The objective is to study the influence of fuel on the morphology and the diffuse reflectance spectrum. The nanoparticles were characterized by field emission scanning electron microscopy (FESEM), the phase was investigated by X-ray diffraction (XRD), the thermal behavior was studied by thermogravimetry analysis (TGA) and differential scanning microscopy (DSC), the color was determined by diffuse reflectance spectroscopy and CIE L*a*b* colorimetric analysis. The average crystallite sizes obtained were 18.40 nm, 42.05 nm, and 18.69 nm when are used glycine, urea, and citric acid, respectively. Finally, the effect of fuel in the diffuse reflectance showed that the scattering of the light by the particles depend of the morphology. Also, the nanopigment was obtained by solution combustion at lower temperature than solid state reaction and it could be used in digital decoration.

Keywords:
solution combustion; ceramic nanopigment; spinel structure; color

1 Introduction

Inorganic pigments are an integral part of many decorative and protective coatings, which are used for the coloration of ceramic materials including glazes, clay bodies, and porcelain enamels1Kim JH, Son BR, Yoon DH, Hwang KT, Noh HG, Cho WS, et al. Characterization of blue CoAlO nano-pigment synthesized by ultrasonic hydrothermal method. 24Ceramics International. 2012; 38(7):5707-5712. http://dx.doi.org/10.1016/j.ceramint.2012.04.015.
http://dx.doi.org/10.1016/j.ceramint.201...
. Recently, inkjet printing has been developed as a non contact direct write technology for the decoration of ceramic tiles2Magdassi S. The chemistry of inkjet inks. Singapore: World Scientific Pub; 2010.. The inks for inkjet printing need micro or nanosized pigment to avoid clogging the nozzle and provide excellent suspension stability. Therefore, submicron and nanosized pigments have a considerable interest in science and technology due to their high surface area, which assures a higher surface coverage and a great number of reflectance points, hence improving the scattering3Pan Z, Wang Y, Huang H, Ling Z, Dai Y and Ke S. Recent development on preparation of ceramic inks in inkjet printinig. Ceramics International. 2015; 41(10):12515-12528. In press. http://dx.doi.org/10.1016/j.ceramint.2015.06.124.
http://dx.doi.org/10.1016/j.ceramint.201...
.

Several authors have studied the synthesis of nanocrystalline double oxides with a spinel type cubic structure (AB2O4) due to the unique potential applications, such as: magnetic materials, catalysis, cathode materials, gas sensitive materials and heat resistant pigments4Torkian L and Daghighi M. Effects of β-alanine on morphology and optical properties of CoAlO nanopowders as a blue pigment. 24Advanced Powder Technology. 2014; 25(2):739-744. http://dx.doi.org/10.1016/j.apt.2013.11.003.
http://dx.doi.org/10.1016/j.apt.2013.11....
. One of the most important spinels in ceramic industry is ZnCr2O4, which is also commonly used as magnetic material5Kagomiya I, Toki M, Kohn K, Hata Y, Kita E and Siratori K. Magnetic clusters in three dimensional spin frustrated system ZnCr2O4. Journal of Magnetism and Magnetic Materials. 2004; 272:E1031-E1032. http://dx.doi.org/10.1016/j.jmmm.2003.12.1028.
http://dx.doi.org/10.1016/j.jmmm.2003.12...
, as humidity sensor6Pokhrel S, Jeyaraj B and Nagaraja KS. Humidity: sensing properties of ZnCr2O4 – ZnO composites. Materials Letters. 2003; 57(22-23):3543-3548. http://dx.doi.org/10.1016/S0167-577X(03)00122-8.
http://dx.doi.org/10.1016/S0167-577X(03)...
and catalytic material7Venugopal A, Sarkari R, Anjaneyulu C, Krishna V, Kumar MK, Narender N, et al. Influencia of acid-base sites on ZnO-ZnCr2O catalyst during dehydrocyclization of aqueous glycerol and ethylenediamine for the synthesis of 2-methylpyrazine: kinetic and mechanism studies. 4Applied Catalysis A, General. 2014; 469:398-409. http://dx.doi.org/10.1016/j.apcata.2013.10.023.
http://dx.doi.org/10.1016/j.apcata.2013....
, and it is synthesized by conventional solid state reaction and requires several heating and grindings steps to ensure homogeneous mixing of various oxides8Kavasoğlu N, Kavasoğlu AS and Bayhan M. Comparative study of ZnCr2O4 – KCrO ceramic humidity sensor using computer controlled humidity measurement set-up. 24Sensors and Actuators. A, Physical. 2006; 126(2):335-361. http://dx.doi.org/10.1016/j.sna.2005.10.049.
http://dx.doi.org/10.1016/j.sna.2005.10....
. Therefore, it is important to develop new cost-effective methods to prepare ZnCr2O4.

The nanoparticles ZnCr2O4 have been synthesized by various methods including sol-gel method9Yazdanbakhsh M, Khosravi I, Goharshadi EK and Youssefi A. Fabrication of nanospinel ZnCrO using sol-gel method and its application on removal of azo dye from aqueous solution. 24Journal of Hazardous Materials. 2010; 184(1-3):684-689. http://dx.doi.org/10.1016/j.jhazmat.2010.08.092. PMid:20863619.
http://dx.doi.org/10.1016/j.jhazmat.2010...
, mechanical activation1010 Marinković Stanojević ZV, Romčević N and Stojanović B. Spectroscopic study of spinel ZnCr2O4 obtained from mechanically activated ZnO – CrO mixtures. 23Journal of the European Ceramic Society. 2007; 27(2-3):903-907. http://dx.doi.org/10.1016/j.jeurceramsoc.2006.04.057.
http://dx.doi.org/10.1016/j.jeurceramsoc...
, micro-emulsion method1111 Niu X, Du W and Du W. Preparation and gas sensing properties of ZnM2O4 (M = Fe, Co, Cr). Sensors and Actuators. B, Chemical. 2004; 99(2-3):405-409. http://dx.doi.org/10.1016/j.snb.2003.12.007.
http://dx.doi.org/10.1016/j.snb.2003.12....
, precursor method1212 Gingasu D, Mindru I, Culita D, Patron L, Calderon-Moreno JM, Preda S, et al. Investigation of nanocrystalline zinc chromite obtained by two soft chemical routes. Materials Research Bulletin. 2014; 49:151-159. http://dx.doi.org/10.1016/j.materresbull.2013.08.062.
http://dx.doi.org/10.1016/j.materresbull...
, microwave processing1313 Parhi P and Manivannan V. Microwave metathetic approach for the synthesis and characterization of ZnCrO. 24Journal of the European Ceramic Society. 2008; 28(8):1665-1670. http://dx.doi.org/10.1016/j.jeurceramsoc.2007.11.005.
http://dx.doi.org/10.1016/j.jeurceramsoc...
, and spray pyrolysis1414 Marinković ZV, Mančić L, Marić R and Milošević O. Preparation of nanostructured Zn-Cr-O spinel powders by ultrasonic spray pyrolysis. Journal of the European Ceramic Society. 2001; 21(10-11):2051-2055. http://dx.doi.org/10.1016/S0955-2219(01)00170-4.
http://dx.doi.org/10.1016/S0955-2219(01)...
. Among the main techniques for generating nanoparticles via the wet chemical route, solution combustion is the one that stands out. This simple technique has many advantages: homogeneous mixing, good stoichiometric control, production of active submicron-size particles in a relatively short processing time, and it involves a combustion process initiated at low temperatures, which makes use of the heat energy liberated by the exothermic reaction between fuel and nitrate ions1515 Alves AK, Bergmann CP and Berutti FA. Novel synthesis and characterization of nanostructured materials. Berlin: Springer Verlag; 2013. http://dx.doi.org/10.1007/978-3-642-41275-2.
http://dx.doi.org/10.1007/978-3-642-4127...
.

However, it has not yet been reported the influence on the color of spinel structure ZnCr2O4 when is synthesized by solution combustion using glycine, urea, and citric acid as fuels. Therefore, the objective of the present study was to produce ceramic nanopigments of ZnCr2O4 by solution combustion using glycine, urea, and citric acid as fuels, in order to evaluate the effect of the fuels on the color of the powders obtained.

2 Experimental

2.1 Synthesis of powders

The ceramic nanopigments ZnCr2O4 were synthesized by solution combustion using glycine, urea, and citric acid as fuels. The stoichiometric composition of the metal nitrates, and the fuels is calculated based on the total oxidizing and reducing valences of the oxidizer (O) and fuel (F) which serve as numerical coefficients for stoichiometric balance so that the equivalence ratio (φₑ) is unity, O/F = 1, therefore, the energy released is at a maximum1616 Patil KC, Hegde MS, Rattan T and Aruna ST. Chemistry of nanocrystalline oxide materials combustion synthesis, properties and applications. Singapore: World Scientific Publishing; 2008. http://dx.doi.org/10.1142/9789812793157.
http://dx.doi.org/10.1142/9789812793157...
. According to the concepts used in propellant chemistry, the elements C, H, Zn, Cu, Cr, or any other metal are considered as reducing elements with the corresponding valencies +4, +1, +2, +2 and +3 (or valency of the metal ion in that compound), respectively. The element oxygen is considered as an oxidizing element with the valency –2. The valency of nitrogen is considered to be zero. Accordingly, the oxidizing and reducing valencies of the compounds used in the combustion mixtures can be calculated.

The first experiment used 11.43g of glycine (NH2CH2COOH, Panreac, 99% purity), the second experiment used 13.74g of urea ((NH2)2CO, Carlo Erba, 99% purity), and the third experiment used 16g of citric acid monohydrate (C6H8O7*H2O, Panreac, 99% purity), each one of which was added to an aqueous solution of 10.4g of zinc nitrate hexahydrate (Zn(NO3)3*6H2O, Panreac, 98%) and 28g of chromium nitrate nonahydrate (Cr(NO3)3*9H2O, Panreac, 98%). The mixtures were slowly evaporated at 90 °C until gels were formed. Then, the gels were slowly heated rapidly until a vigorous self-propagating combustion reaction to obtain the powders, then the samples were calcined at 700 °C and 6 h.

2.2 Characterization methods

X-Ray Diffraction (XRD) studies of the samples as-prepared and calcined were carried out using a PANanalytical X'Spert Pro X-ray diffractometer, using Cu Kα radiation (0.15406 nm). The X-ray generator voltage was 45 kV and the tube current was of 45 mA, with scan step size 0.013° and step time of 1.0 s. The scanning was between 17° and 69°(2θ). The experimental diffractograms were interpreted with the help of High Score X'Spert program.

The surface morphology of polycrystalline samples of the ceramic pigments ZnCr2O4 were analyzed by Field Emission Scanning Electron Microscopy (FESEM) using a FESEM - JEOL JSM 6701F. The operational voltages were 12kV and 15 kV, and electricity current of 10 µA for generating images with a working distance of 6.2 mm. The samples were subjected to high vacuum, and coated with a layer of gold to improve its electrical conductivity.

The thermal behavior of the powders was followed by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) using Thermal Analyzer Netzsch STA 490 C. The samples were placed in an open alumina crucible and heated with a heating rate of 10 °C/min from room temperature up to 900 °C, under the flow of 20 mL/min of nitrogen atmosphere.

Analysis of visible diffuse reflectance and colorimetric coordinates CIEL*a*b* of the pigments were performed on a UV-VIS spectrophotometer GlacierTMX with spectral range 200-1050 nm. Colorimetric data were measured by combining object spectral data with data representing a CIE standard observer of 10° and a CIE standard illuminant D65 (day light), as described in the standard practice ASTM E3081717 American Society for Testing and Materials - ASTM. ASTM E308-15: standard practice for computing the colors of objects by using the CIE system. West Conshohocken: ASTM International; 2015. http://dx.doi.org/10.1520/E0308-15.
http://dx.doi.org/10.1520/E0308-15...
. In this method, L* is the lightness axis [black (0) - white (100)], b* is the blue (–) and yellow (+) axis, a* is the green (–) and red (+) axis.

3 Results and Discussion

Figure 1 shows the thermal analysis of differential scanning calorimetry (DSC) and thermogravimetric analysis for the samples obtained after combustion reaction between fuels and the metal nitrates. The three graphics present a similar form where an exothermic band is identified with a peak about 100 °C, which is probably due to loss of decomposition of organic matter by the sample, also another exothermic band is observed between 200 °C and 900 °C, which are ascribed to organic matter that was not removed during combustion, in the literature is reported the decomposition of glycine in a nitrogen atmosphere1818 Manukyan KV, Cross A, Roslyakov S, Rouvimov S, Rogachev AS, Wolf E, et al. Solution combustion synthesis of nano-crystalline metallic materials: mechanistic studies. The Journal of Physical Chemistry C. 2013; 117(46):24417-24427. http://dx.doi.org/10.1021/jp408260m.
http://dx.doi.org/10.1021/jp408260m...
, which started at 250 °C with the production of NH3, CO2, H2O, a dipeptide and 2,5-piperazinedione compounds, later at 450 °C dipeptide and 2,5-piperazinedione are decomposed in HNCO, HCN, CO2, NH3, and H2O. The results show that the products of synthesis are different, because there is a mass loss between 25 °C and 900 °C which are of 20%, 8%, and 10% for glycine, urea, and citric acid, respectively. Therefore, there is an incomplete combustion in three cases.

Figure 1
DSC and TG curves of ZnCr2O4 of the powders as prepared.

The XRD patterns of the polycrystalline powders as-prepared and calcined in air at 700 °C and 6 h are shown in the Figure 2. The powders synthesized with glycine, urea, and citric acid have diffraction peaks that can be indexed well with the reference of spinel structure ZnCr2O4 (JCPDS 022-1107) which is a cubic crystal system with space group Fd3m. Therefore, the temperatures of combustion between the fuels and metal nitrates were optimum for the formation of the pure phase. However, the samples are calcined at 700 °C and 6 h due to presence of organic compounds as it was shown in the thermal analysis. The Table 1 shows the average crystallite sizes of the powders as-prepared and calcined, which were determined from the full width at half maximum (FWHM) of the main intense peak (311) using Scherrer equation1919 Waseda Y, Matsubara E and Shinoda K. X-Ray diffraction crystallograpgy introduction, examples and solved problems. Heidelberg: Springer Verlag; 2011.. It can be seen that the calcinations of the powders at 700 °C and 6 h increase the sizes of the crystallites.

Figure 2
X-ray diffraction patterns for ZnCr2O4 obtained by glycine-nitrate, urea-nitrate and citric acid-nitrate.
Table 1
Average crystallite size of powders synthesized by solution combustion as prepared and calcinated.

Figure 3 presents the FESEM micrographs of the ZnCr2O4 obtained by solution combustion with the fuels glycine, urea, and citric acid, which reveal agglomerated, porous, and sponge-like morphologies of the particles, these characteristics are reported in the scientific literature for the solution combustion synthesis2020 Oliveira FF, Da Dalt S, Sousa VC and Bergmann CP. Synthesis of SrBiTa. 22O9 by solution combustion and its characterizationPowder Technology. 2012; 225:239-243. http://dx.doi.org/10.1016/j.powtec.2012.04.023.
http://dx.doi.org/10.1016/j.powtec.2012....
,2121 Costa ACFM, Silva VJ, Xin CC, Vieira DA, Cornejo DR and Kiminami RHGA. Effect of urea and glycine fuels on the combustion reaction synthesis of Mn-Zn ferrites: evaluation of morphology and magnetic properties. Journal of Alloys and Compounds. 2010; 495(2):503-505. http://dx.doi.org/10.1016/j.jallcom.2009.10.065.
http://dx.doi.org/10.1016/j.jallcom.2009...
, this is due to evolution of the large amount of gaseous products during combustion, which produces highly porous voluminous powders, and these parameters dependent of fuel used in the synthesis. The glycine shows higher porous than urea and citric acid, however, it is important to note that the samples shows agglomeration of nanoparticles, but the urea shows nanometric crystals of octahedral shape of size bigger than the glycine and citric acid, which is consistent with the values calculate from XRD patterns by Scherrer equation. Therefore, these results indicate that a change in the fuel used in the synthesis lead to significant changes in the microstructure of the powders.

Figure 3
FESEM micrographs for ZnCr2O4 obtained by glycine-nitrate (a), urea-nitrate (b), and citric acid-nitrate (c).

Figure 4 shows the diffuse reflectance factor spectrums in the range of 400-700 nm of the powders ZnCr2O4synthesized by solution combustion which were annealing at 700 °C and 2h. The minima reflectance peaks between 420-430 nm and 580-600 nm can be assigned to 4A2g4T2g and 4A2g4T1g transitions of octahedral Cr(III) (d3) ion, respectively. These values are in good agreement with previously published data2222 Gingasu D, Mindru I, Patron L, Culita D, Calderon-Moreno JM, Diamandescu L, et al. Precursor method: a non conventional route for the synthesis of ZnCrO spinel. 24Journal of Physics and Chemistry of Solids. 2013; 74(9):1295-1302. http://dx.doi.org/10.1016/j.jpcs.2013.04.007.
http://dx.doi.org/10.1016/j.jpcs.2013.04...
,2323 Singh N and Rhee JY. Electronic structures and optical properties of spinel ZnCrO. 24Journal of the Korean Physical Society. 2010; 57(5):1233-1237. http://dx.doi.org/10.3938/jkps.57.1233.
http://dx.doi.org/10.3938/jkps.57.1233...
. The most important effect of the fuel in the synthesis of ZnCr2O4 can be appreciated in the diffuse reflectance percentages, when the glycine is used, the reflectance percentages in the visible spectrum are higher than urea and citric acid, for example with wavelength of 550 nm, the reflectance percentages are: 50% (glycine), 42,5% (urea), and 25% (citric acid), these results are a consequence of the presence of volumetric defects, because at the microscopic level the loss due to bulk scattering is a result of the interaction of the electromagnetic wave with the microstructure of the sample. The total scattering loss coefficient is attributed to surface scatter, resulting from material surface imperfections, and porosity2424 Zhang W, Lu T, Wei N, Wang Y, Ma B, Li F, et al. Assessment of light scattering by pores in Nd:YAG transparent ceramics. Journal of Alloys and Compounds. 2012; 520:36-41. http://dx.doi.org/10.1016/j.jallcom.2011.12.012.
http://dx.doi.org/10.1016/j.jallcom.2011...
. When glycine is used, the porosity is higher that urea and citric acid, as it was showed in the FESEM micrographs, for that reason the scattering of light increases. Therefore, the increase in diffuse reflectance of glycine is attributed to increase of scattering light by high porosity of the powder, due to generated gasses during the combustion reaction, whereas in the case of urea and citric acid the gasses are lower than glycine. Also, the particle size is lower in the glycine, which increases the surface area, and consequently the scattering of light also increases.

Figure 4
Visible spectrum of ZnCr2O4 powders.

Table 2 shows the colorimetric coordinates CIEL*a*b* of ZnCr2O4 obtained by solution combustion, colorimetric coordinate L* shows a higher value when is used glycine as fuel, because the scattering of the light increases due to porosity of the powder, in another way the slower value when is used citric acid as fuel, which shows the color is a function of porosity and microstructure of the samples, the coordinates a* and b* have low values for the powder obtained using citric acid, which show low values of color, for the powders obtained using glycine and citric acid, the negative value in colorimetric coordinate a* shows that they are green, whereas the positive value in colorimetric b* indicates the samples are yellow.

Table 2
Colorimetric coordinates CIEL*a*b*.

4 Conclusions

Ceramic nanopigment ZnCr2O4 has been synthesized by solution combustion using glycine, urea, and citric acid and it was shown that when the combustion reaction produces a great amount of gases, the porosity and the scattering of the light increases, therefore, the color of the powder change, which indicates that the final color of the powders is a function of the fuel used. Also, the nanopigments were obtained at temperatures and reaction times lower than solid state reaction, which would avoid the use of mineralizing fluxing agents for the synthesis of the pigment, in addition, the small average crystallite sizes of 18.4 nm (glycine), 42.1 nm (urea), and 18.7 nm (citric acid) indicate that they could be use in digital decoration.

References

  • 1
    Kim JH, Son BR, Yoon DH, Hwang KT, Noh HG, Cho WS, et al. Characterization of blue CoAlO nano-pigment synthesized by ultrasonic hydrothermal method. 24Ceramics International. 2012; 38(7):5707-5712. http://dx.doi.org/10.1016/j.ceramint.2012.04.015.
    » http://dx.doi.org/10.1016/j.ceramint.2012.04.015
  • 2
    Magdassi S. The chemistry of inkjet inks. Singapore: World Scientific Pub; 2010.
  • 3
    Pan Z, Wang Y, Huang H, Ling Z, Dai Y and Ke S. Recent development on preparation of ceramic inks in inkjet printinig. Ceramics International. 2015; 41(10):12515-12528. In press. http://dx.doi.org/10.1016/j.ceramint.2015.06.124.
    » http://dx.doi.org/10.1016/j.ceramint.2015.06.124
  • 4
    Torkian L and Daghighi M. Effects of β-alanine on morphology and optical properties of CoAlO nanopowders as a blue pigment. 24Advanced Powder Technology. 2014; 25(2):739-744. http://dx.doi.org/10.1016/j.apt.2013.11.003.
    » http://dx.doi.org/10.1016/j.apt.2013.11.003
  • 5
    Kagomiya I, Toki M, Kohn K, Hata Y, Kita E and Siratori K. Magnetic clusters in three dimensional spin frustrated system ZnCr2O4. Journal of Magnetism and Magnetic Materials. 2004; 272:E1031-E1032. http://dx.doi.org/10.1016/j.jmmm.2003.12.1028.
    » http://dx.doi.org/10.1016/j.jmmm.2003.12.1028
  • 6
    Pokhrel S, Jeyaraj B and Nagaraja KS. Humidity: sensing properties of ZnCr2O4 – ZnO composites. Materials Letters. 2003; 57(22-23):3543-3548. http://dx.doi.org/10.1016/S0167-577X(03)00122-8.
    » http://dx.doi.org/10.1016/S0167-577X(03)00122-8
  • 7
    Venugopal A, Sarkari R, Anjaneyulu C, Krishna V, Kumar MK, Narender N, et al. Influencia of acid-base sites on ZnO-ZnCr2O catalyst during dehydrocyclization of aqueous glycerol and ethylenediamine for the synthesis of 2-methylpyrazine: kinetic and mechanism studies. 4Applied Catalysis A, General. 2014; 469:398-409. http://dx.doi.org/10.1016/j.apcata.2013.10.023.
    » http://dx.doi.org/10.1016/j.apcata.2013.10.023
  • 8
    Kavasoğlu N, Kavasoğlu AS and Bayhan M. Comparative study of ZnCr2O4 – KCrO ceramic humidity sensor using computer controlled humidity measurement set-up. 24Sensors and Actuators. A, Physical. 2006; 126(2):335-361. http://dx.doi.org/10.1016/j.sna.2005.10.049.
    » http://dx.doi.org/10.1016/j.sna.2005.10.049
  • 9
    Yazdanbakhsh M, Khosravi I, Goharshadi EK and Youssefi A. Fabrication of nanospinel ZnCrO using sol-gel method and its application on removal of azo dye from aqueous solution. 24Journal of Hazardous Materials. 2010; 184(1-3):684-689. http://dx.doi.org/10.1016/j.jhazmat.2010.08.092. PMid:20863619.
    » http://dx.doi.org/10.1016/j.jhazmat.2010.08.092
  • 10
    Marinković Stanojević ZV, Romčević N and Stojanović B. Spectroscopic study of spinel ZnCr2O4 obtained from mechanically activated ZnO – CrO mixtures. 23Journal of the European Ceramic Society. 2007; 27(2-3):903-907. http://dx.doi.org/10.1016/j.jeurceramsoc.2006.04.057.
    » http://dx.doi.org/10.1016/j.jeurceramsoc.2006.04.057
  • 11
    Niu X, Du W and Du W. Preparation and gas sensing properties of ZnM2O4 (M = Fe, Co, Cr). Sensors and Actuators. B, Chemical. 2004; 99(2-3):405-409. http://dx.doi.org/10.1016/j.snb.2003.12.007.
    » http://dx.doi.org/10.1016/j.snb.2003.12.007
  • 12
    Gingasu D, Mindru I, Culita D, Patron L, Calderon-Moreno JM, Preda S, et al. Investigation of nanocrystalline zinc chromite obtained by two soft chemical routes. Materials Research Bulletin. 2014; 49:151-159. http://dx.doi.org/10.1016/j.materresbull.2013.08.062.
    » http://dx.doi.org/10.1016/j.materresbull.2013.08.062
  • 13
    Parhi P and Manivannan V. Microwave metathetic approach for the synthesis and characterization of ZnCrO. 24Journal of the European Ceramic Society. 2008; 28(8):1665-1670. http://dx.doi.org/10.1016/j.jeurceramsoc.2007.11.005.
    » http://dx.doi.org/10.1016/j.jeurceramsoc.2007.11.005
  • 14
    Marinković ZV, Mančić L, Marić R and Milošević O. Preparation of nanostructured Zn-Cr-O spinel powders by ultrasonic spray pyrolysis. Journal of the European Ceramic Society. 2001; 21(10-11):2051-2055. http://dx.doi.org/10.1016/S0955-2219(01)00170-4.
    » http://dx.doi.org/10.1016/S0955-2219(01)00170-4
  • 15
    Alves AK, Bergmann CP and Berutti FA. Novel synthesis and characterization of nanostructured materials. Berlin: Springer Verlag; 2013. http://dx.doi.org/10.1007/978-3-642-41275-2.
    » http://dx.doi.org/10.1007/978-3-642-41275-2
  • 16
    Patil KC, Hegde MS, Rattan T and Aruna ST. Chemistry of nanocrystalline oxide materials combustion synthesis, properties and applications. Singapore: World Scientific Publishing; 2008. http://dx.doi.org/10.1142/9789812793157.
    » http://dx.doi.org/10.1142/9789812793157
  • 17
    American Society for Testing and Materials - ASTM. ASTM E308-15: standard practice for computing the colors of objects by using the CIE system. West Conshohocken: ASTM International; 2015. http://dx.doi.org/10.1520/E0308-15.
    » http://dx.doi.org/10.1520/E0308-15
  • 18
    Manukyan KV, Cross A, Roslyakov S, Rouvimov S, Rogachev AS, Wolf E, et al. Solution combustion synthesis of nano-crystalline metallic materials: mechanistic studies. The Journal of Physical Chemistry C. 2013; 117(46):24417-24427. http://dx.doi.org/10.1021/jp408260m.
    » http://dx.doi.org/10.1021/jp408260m
  • 19
    Waseda Y, Matsubara E and Shinoda K. X-Ray diffraction crystallograpgy introduction, examples and solved problems. Heidelberg: Springer Verlag; 2011.
  • 20
    Oliveira FF, Da Dalt S, Sousa VC and Bergmann CP. Synthesis of SrBiTa. 22O9 by solution combustion and its characterizationPowder Technology. 2012; 225:239-243. http://dx.doi.org/10.1016/j.powtec.2012.04.023.
    » http://dx.doi.org/10.1016/j.powtec.2012.04.023
  • 21
    Costa ACFM, Silva VJ, Xin CC, Vieira DA, Cornejo DR and Kiminami RHGA. Effect of urea and glycine fuels on the combustion reaction synthesis of Mn-Zn ferrites: evaluation of morphology and magnetic properties. Journal of Alloys and Compounds. 2010; 495(2):503-505. http://dx.doi.org/10.1016/j.jallcom.2009.10.065.
    » http://dx.doi.org/10.1016/j.jallcom.2009.10.065
  • 22
    Gingasu D, Mindru I, Patron L, Culita D, Calderon-Moreno JM, Diamandescu L, et al. Precursor method: a non conventional route for the synthesis of ZnCrO spinel. 24Journal of Physics and Chemistry of Solids. 2013; 74(9):1295-1302. http://dx.doi.org/10.1016/j.jpcs.2013.04.007.
    » http://dx.doi.org/10.1016/j.jpcs.2013.04.007
  • 23
    Singh N and Rhee JY. Electronic structures and optical properties of spinel ZnCrO. 24Journal of the Korean Physical Society. 2010; 57(5):1233-1237. http://dx.doi.org/10.3938/jkps.57.1233.
    » http://dx.doi.org/10.3938/jkps.57.1233
  • 24
    Zhang W, Lu T, Wei N, Wang Y, Ma B, Li F, et al. Assessment of light scattering by pores in Nd:YAG transparent ceramics. Journal of Alloys and Compounds. 2012; 520:36-41. http://dx.doi.org/10.1016/j.jallcom.2011.12.012.
    » http://dx.doi.org/10.1016/j.jallcom.2011.12.012

Publication Dates

  • Publication in this collection
    Sep-Oct 2015

History

  • Received
    09 July 2015
  • Reviewed
    12 Sept 2015
ABM, ABC, ABPol UFSCar - Dep. de Engenharia de Materiais, Rod. Washington Luiz, km 235, 13565-905 - São Carlos - SP- Brasil. Tel (55 16) 3351-9487 - São Carlos - SP - Brazil
E-mail: pessan@ufscar.br