Acessibilidade / Reportar erro

Determination of serum lithium: comparison between atomic emission and absorption spectrometry methods

Determinação sérica de lítio: comparação das metodologias de espectrometria de emissão e de absorção atômica

Abstracts

Introduction:

The therapeutic monitoring of lithium, through concentration measurements, is important for individual dose adjustment, as a marker of treatment adherence and to prevent poisoning and side effects.

Objectives:

Validate and compare two methods - atomic emission and atomic absorption - for the determination of lithium in serum samples.

Methodology:

Parameters such as specificity, precision, accuracy, limit of detection (LOD) and linearity were considered. The atomic absorption spectrometer was used, operating in either emission or absorption mode. For the quantitative comparison of 30 serum samples from patients with mood disorder treated with lithium, the results were submitted to Student's t-test, F-test and Pearson's correlation.

Results:

The limit of quantification (LOQ) was established as 0.05 mEq/l of lithium, and calibration curves were constructed in the range of 0.05-2 mEq/l of lithium, using aqueous standards. Sample preparation time was reduced, what is important in medical laboratory.

Conclusion:

Both methods were considered satisfactory, precise and accurate and can be adopted for lithium quantification. In the comparison of quantitative results in lithium-treated patients through statistical tests, no significant differences were observed. Therefore the methods for lithium quantification by flame atomic absorption spectrometry (FAAS) and flame atomic emission spectrometry (FAES) may be considered similar.

lithium; validation; flame atomic absorption spectrometry (FAAS); flame atomic emission spectrometry (FAES)


Introdução:

A monitorização terapêutica por meio da determinação sérica de lítio é importante para proporcionar o ajuste individual da dose, como marcador de adesão e para prevenir intoxicações.

Objetivos:

Validar e comparar duas metodologias, a de emissão e a de absorção atômicas, para determinação de lítio em amostras de soro.

Metodologia:

Foram determinados parâmetros de especificidade, precisão, exatidão, limite de detecção e linearidade a fim de validar as metodologias para determinação de lítio. Foi utilizado espectrômetro de absorção atômica, funcionando no modo de emissão ou de absorção. Para comparação das metodologias foram utilizados os testes estatísticos (teste t de Student, o teste F e a correlação de Pearson) nos resultados quantitativos de 30 amostras de soro sanguíneo de pacientes que faziam uso terapêutico de lítio para o controle do transtorno de humor bipolar (THB).

Resultados:

Foram estabelecidos um limite de quantificação de 0,05 mEq/l de lítio e curvas de calibração de 0,05 a 2 mEq/l de lítio, construídas utilizando padrões aquosos, com redução no tempo de preparo das amostras, principalmente para ser utilizado em laboratório de análises clínicas.

Conclusão:

Os dois métodos foram considerados satisfatórios, precisos e exatos e podem ser adotados para a quantificação do lítio. Na comparação dos dois métodos por testes estatísticos em amostras de pacientes tratados com o fármaco, não foram observadas diferenças significativas entre os resultados encontrados. Desta forma, os métodos para quantificação do lítio por espectrometria de absorção atômica em chama (FAAS) e espectrometria de emissão atômica em chama (FAES) podem ser considerados semelhantes.

lítio; validação; espectrometria de absorção atômica; espectrometria de emissão atômica


INTRODUCTION

The bipolar affective disorder is a chronic condition that characterizes by mood swings, with alternate episodes of mania and depression( 88. MICHELON, L.; VALLADA, H. Fatores genéticos e ambientais na manifestação do transtorno bipolar. Rev Psiq Clín, v. 32, suppl 1, p. 21-27, 2005. ). Treatment includes lithium, valproate, carbamazepine, typical and atypical antipsychotics( 55. GOODWIN, G. M. Evidence-based guidelines for treating bipolar disorder: revised second edition - recommendations from the British Association for Psychopharmacology. J Psychopharmacol, v. 23, n. 4, p. 346-88, 2009. , 77. KAPCZINSKI, F. et al. Tratamento farmacológico do transtorno bipolar: as evidências de ensaios clínicos randomizados. Rev Psiq Clín, v. 32, suppl 1, p. 34-38, 2005. ) when it aims at reducing manic symptoms; and antidepressants, lamotrigine, fluoxetine and olanzapine when it is necessary to fight depression. Treatment must be established considering individual aspects.

The use of lithium salts points to the necessity of therapeutic monitoring through determination of serum lithium, as the therapeutic effect of lithium is directly related to its concentration in serum, whose therapeutic levels range between 0.6 and 1.2 mEq/l. Serum levels above 1.5 mEq/l( 1212. SPROULE, B. Lithium in bipolar disorder: can drug concentrations predict therapeutic effect? Clin Pharmacokinet, v.41, n. 9, p. 639-60, 2002. )are considered toxic; therefore, it is a drug with narrow therapeutic index( 1010. ROSA, A. R. et al. Monitoramento de adesão ao tratamento com lítio. Rev Psiq Clín, v. 33, n. 5, p. 249-61, 2006. ).

Monitoring is important also because there is influence on the therapeutic response to lithium, depending on the heterogeneity of bipolar disorders, leading to pharmacokinetic differences following the patient's clinical state. In other words, lithium levels decrease in patients during hypomania, remain constant in normal states and increase during depression( 1111. SCOTT, J.; POPE, M. Nonadherence with mood stabilizers: prevalence and predictors. J Clin Psychiatry, v. 63, n. 5, p. 384-90, 2002. , 1212. SPROULE, B. Lithium in bipolar disorder: can drug concentrations predict therapeutic effect? Clin Pharmacokinet, v.41, n. 9, p. 639-60, 2002. ).

Lithium concentrations in plasma, serum, urine or other body fluids may be determined by flame atomic emission spectrometry (FAES), also known as flame photometry, a colorimetric semi-quantitative method with ferric periodate( 99. PASSARELI, M. M. Saliva como controle terapêutico do lítio. São Paulo, 1987. Tese (doutoramento) - Universidade de São Paulo. ), using a lithium ion-selective electrode( 33. FERNANDES A. S. G.; LEAL A. C. Lítio e sua aplicação terapêutica na psicose maníaco-depressiva. Ciências Farmacêuticas da Faculdade de Farmácia de Lisboa, 2002. ), and by flame atomic absorption spectrometry (FAAS)( 99. PASSARELI, M. M. Saliva como controle terapêutico do lítio. São Paulo, 1987. Tese (doutoramento) - Universidade de São Paulo. ).

Since many clinical decisions are based on analysis results, methodologies must have strict quality controls. Nowadays there is a formal demand for clinical laboratories to introduce quality assurance measures into their services, and it is fundamental that they have means and objective criteria to demonstrate, through validation, that the assay methods they employ yield reliable results that meet the expected quality( 66. INSTITUTO NACIONAL DE METROLOGIA (INMETRO). Orientação sobre validação de métodos analíticos. DOQ_CGCRE-008, revisão 3, 2010. ).

The aims of this work are to validate and to compare two methods for determination of lithium in serum samples - atomic emission and atomic absorption - so that they are used in medical laboratories; also to produce knowledge and to contribute to the formation of qualified staff resources in this study area.

METHODOLOGY

Instrument

An atomic absorption Varian (Mulgrave, Australia) model SPECTRAA 55 spectrometer was used, operating in either emission or absorption mode. In the absorption mode, a lithium hollow cathode lamp was employed, at a current of 5 mA. Operational parameters of the equipment were adjusted as recommended by the manufacturer: wavelength of 670.8 nm, slit width of 1 nm, burner height of 7.5 mm, air as oxidizer and acetylene as fuel (air/ acetylene) and a stoichiometric flame.

Materials and reagents

The following were used: volumetric balloon and test tubes of 10 ml; Eppendorf (Westbury, USA) calibrated variable-volume micropipettes; vortex mixer FANEM for the homogenization of solutions and samples. As reagents, the following were used: 1000 mg/l lithium reference analytical solution ( J.T.BAKER, USA) certified by the National Institute of Standards and Technology (NIST) of the United States; Special Reagent Water (SRW) obtained from Millipore system (Bedford, USA), to prepare standard working solutions and sample dilution.

Samples: origin, collection and preparation

Quality control serum samples (serum of patients not taking lithium), as well as samples from bipolar mood disorder patients treated with lithium, were provided by a clinical laboratory in Fortaleza, Brazil.

For the quality control (QC) samples to be used in the validation, the serum of patients not taking lithium and lithium reference standard solutions (1,000 mg of the element) were provided. The quality controls were prepared as follows: a) low concentration quality control (LQC): serum with addition of the analyte, concentration of 0.15 mEq/l, three times the lower limit of quantification (LLOQ) of the method; b) medium concentration quality control (MQC): serum with addition of the analyte, concentration of 1 mEq/l, average of LLOQ and the upper limit of quantification (ULOQ); c) high concentration quality control (HQC): serum with addition of the analyte, concentration of 1.5 mEq/l, 75% of the highest concentration of the calibration curve.

For the treatment of samples, a tenfold dilution with reagent water was made, allowing an absorption measurement within the linear calibration range of the spectrometer. This dilution is important for the reduction of matrix effect. Thus, 200 µl of the sample were diluted with 1,800 µl of water in a 5 ml test tube and homogenized for 30 seconds on a vortex mixer.

Validation

The validation was performed based on the parameters laid down in Resolution RDC 27, of May 17, 2012, of the Brazilian Health Surveillance Agency (ANVISA)( 11. AGÊNCIA NACIONAL DE VIGILÂNCIA SANITÁRIA (ANVISA) BRASIL. Resolução nº 27, de 17 de maio de 2012. Dispõe sobre os requisitos mínimos para a validação de métodos bioanalíticos empregados em estudos com fins de registro e pós-registro de medicamentos. Diário Oficial da União, 22 de maio de 2012. ).

Linearity and working range

In order to verify the method ability to provide a signal that is directly proportional to lithium concentration within a certain application range, standard solutions were prepared at variable concentrations (0.1, 0.2, 0.5, 1, 1.5 and 2 mEq/l), which were selected according to the therapeutic range and the information on linearity included in the equipment manual. After reading the concentrations using both methods, FAAS and FAES, graphs showing the analytical response were produced to identify the linear range, both by visual inspection and using the correlation coefficient (R). The acceptance criterion is R > 0.99.

Limit of quantification

The limit of quantification (LOQ) was established through analysis of solutions containing decreasing concentrations of the analyte up to the lowest determinable level with acceptable precision and accuracy (≤ 20%). Samples were prepared with addition of the analyte standard solution at concentrations of 0.01, 0.02, 0.03, 0.04 and 0.05 mEq/l. Five replicates were carried out, and precision and accuracy were evaluated for each concentration.

Calibration curve

For the construction of calibration curves, concentrations of 0.05, 0.1, 0.2, 0.5, 1, 1.5 and 2 mEq/l of lithium were prepared, including the LLOQ and the ULOQ, from dilutions of 1,000 mg/l stock solution. At the end of solution preparation, readings were done, using both methods, whose calibration curves were constructed establishing the relationship between signal and concentration, through a linear mathematical model and using the computer program Origin 5.0.

Specificity

In order to evaluate the matrix effect, a test was conducted that consists of the comparison of calibration in two ways: with calibration standards prepared in reagent water (aqueous standards) and with calibration standards prepared with serum matrix obtained from patients not using lithium. To determine specificity, serum samples obtained from six different patients were analyzed.

Accuracy and precision

Accuracy and precision assays of both methods were conducted in a same run (intra-run accuracy and precision) and in three different runs and in different days (inter-run accuracy and precision). In each run five replicates were prepared, at concentrations: LLOQ (0.05 mEq/l), LQC (0.15 mEq/l), MQC (1 mEq/l), HQC (1.5 mEq/l). Intra-run (five replicates) and inter-run (15 replicates) accuracy and precision were calculated based on the obtained values. The acceptance criteria do not allow values higher than 15% as coefficient of variation (CV) and relative standard deviation (RSD). For LLOQ, values up to 20% are admitted.

Use of the methods after validation

Thirty samples of blood serum from lithium-treated patients were used. Collection was performed in 5 ml evacuated tubes, with clot activator and, after 20 minutes at room temperature, the samples were centrifuged (2,500 rpm, 15 min) to separate blood serum. Before analysis, samples were diluted ten times with reagent water type 1 (200 µl of the sample were diluted in 1,800 µl of water) and homogenized for 30 seconds.

Methodology comparison

We used 30 serum samples from lithium-treated patients, analyzed them with both methods, making a comparison using the Student's t-test, F test and Pearson correlation.

Ethical aspects

The study was designed in accordance with the guidelines and norms on research involving human beings (Resolution no. 196/1996). It was submitted to the research ethics committee of Universidade Federal do Ceará, and approved in the meeting held on December 9, 2010, with protocol number 282/10.

RESULTS AND DISCUSSIONS

Validation

Linearity and working range

The curves constructed at concentrations of 0.1, 0.2, 0.5, 1, 1.5 and 2 (mEq/l), using the techniques FAAS and FAES, are presented in Figure 1. The result shows that in the used working range (from 0.1 to 2 mEq/l of lithium), FAAS demonstrates linearity, with R equal to 0.9998, and the linear equation obtained was Y = 0.1866× + 0.001. In determination by FAES, the obtained R was 0.9998, but we could observe, both visually and by comparison between R values, that FAAS presents better linearity. FAES demonstrates a slight loss of linearity, at and above the concentration of 1.5 mEq/l. The linear equation obtained in this method was Y = 0.484× + 0.0326.

FIGURE 1
Calibration curves for assessment of linearity by techniques FAAS and FAES FAAS: flame atomic absorption spectrometry; FAES: flame atomic emission spectrometry.

Specificity

The calibration curves obtained with calibration standards prepared in reagent water (aqueous standards) and serum matrix (patients who do not use lithium as treatment) using FAAS and FAES techniques were parallel, and the slope values were very close, with no significant difference between calibration curves. One may say there was no interference from the matrix.

The specificity assay with serum samples obtained from six different patients, using the therapeutic range of 0.6 to 1.2 mEq/l, demonstrated a very small response, on average, 0.011 mEq/l for FAAS and 0.013 mEq/l for FAES, without compromising the identification and/or quantification of the substance of interest. The obtained values may be due to the endogenous lithium or to other interferences, such as that of strontium, with an absorption maximum at 671 nm( 22. AMERICAN PUBLIC HEALTH ASSOCIATION (APHA). Standard Methods for the Examination of the Water and Wastewater. 19th ed. New York: 1995. ).

The previously observed response influenced the determination of LLOQ. Therefore, to solve this problem, the equipment was zeroed with a serum blank after treatment (serum from a patient not undergoing lithium treatment, diluted ten times), using the curves generated with aqueous standards. Thus, the readings were equal to zero or very close to it. In the assay with lithium-enriched serum samples compared, by calibration curves, with aqueous standards, interference was not detected, for it was very small and did not affect calibration.

Limit of quantification

The LOQ established by means of analysis in quintuplet of solutions containing decreasing concentrations of the analyte, 0.01, 0.02, 0.03, 0.04 and 0.05 mEq/l are shown in Table 1. Precision and accuracy were obtained within the acceptance criteria, starting at the concentration of 0.03 mEq/l for FAAS and at 0.01 mEq/l for FAES; however, the concentration of 0.05 mEq/l was selected as LOQ for both methods, because it is a safer and acceptable limit for the aims of the method.

TABLE 1
Determination of the limit of quantification (n = 5)

Calibration curve

The average of calibration curves, using both methods, at concentrations of 0.05, 0.1, 0.2, 0.5, 1, 1.5 and 2 mEq/l of lithium are shown in Figure 2, presenting R = 0.9996 and linear equation Y = 0.1962× + 0.0019 for FAAS, and R = 0.9955 and linear equation Y = 0.4897× + 0.027 for FAES.

FIGURE 2
Calibration curves in the concentrations from 0.05 to 2 mq/l lithium by techniques FAAS and FAES FAAS: flame atomic absorption spectrometry; FAES: flame atomic emission spectrometry.

Accuracy and precision

The assays of intra-run and inter-run accuracy and precision for both methods are described in Table 2. Both methods are considered accurate and precise, as they presented accuracy and precision within the established norms: CV and relative standard error (RSE) below 15%.

TABLE 2
Determination of intra- (n = 5) and inter-assay (n = 15) precision and accuracy

Method comparison

For comparison of both methods, 30 samples from patients treated with lithium carbonate were analyzed. For each sample both results were similar, but not identical (Table 3). The difference between both methods was calculated for each sample, as well as the average of differences and the standard deviation of differences. The applied t-test, with 95% confidence and 29 (n-1) degrees of freedom, presented a result of tcalculated equal to 1.855, which is lower than ttabulated equal to 2.045. Therefore, there is more than 95% chance that both results are the same.

TABLE 3
Result of lithium dosage in patients (n = 30) treated with lithium carbonate and comparison of both methods (t-test)

In order to verify whether there is a significant difference between the variances of both methods, the F-test was applied at the 5% significance level based on the degrees of freedom 29 of both variances. Standard deviations were calculated from the 30 results of lithium concentrations in patients obtained for each method (Table 3) and the result presented Fcalculated equal to 0.982, while Ftabulated was 1.86. Since Fcalculated was lower than Fcritical, one may conclude that there is no significant difference between precisions.

The results obtained through FAAS and FAES were compared based on linear regression and the Pearson correlation. The result is presented in Figure 3. The graph and the descriptive statistics were obtained by using software Minitab 15.0.

FIGURE 3
Correlation between the results obtained by the techniques FAAS and FAES FAAS: flame atomic absorption spectrometry; FAES: flame atomic emission spectrometry.

The obtained result demonstrates there is strong linear relation because the value for the Pearson correlation coefficient (0.9987) is very close to one. It indicates that data follow the approximate behavior of a line (Figure 3). It is possible to conclude there is a strong correlation between the results of both methods.

CONCLUSION

Comparing FAES and FAAS as to the necessary parameters for validation (specificity, linearity, precision, accuracy, LOQ), both were considered satisfactory. They were considered accurate and precise, because they met the criteria adopted by ANVISA, through Resolution no. 27/2012, and may be used for lithium quantification. FAAS presented better linearity in the used working range (0.1 to 2 mEq/l of lithium) when compared to FAES, in which one may perceive a loss of linearity, mainly starting at the 1.5 mEq/l concentration.

Matrix interference was not observed, and calibration curves for both methods were constructed using aqueous standards, a simpler preparation method that provides a reduction in sample preparation time, especially to be used in clinical laboratories.

The quantitative analysis of lithium in samples from patients treated with the drug comparing both methods through statistical tests showed there are no significant differences between the results. And the test called Pearson's correlation coefficient showed a strong correlation between both methods. Thus, the methods FAAS and FAES for lithium quantification may be considered similar.

REFERENCES

  • 1
    AGÊNCIA NACIONAL DE VIGILÂNCIA SANITÁRIA (ANVISA) BRASIL. Resolução nº 27, de 17 de maio de 2012. Dispõe sobre os requisitos mínimos para a validação de métodos bioanalíticos empregados em estudos com fins de registro e pós-registro de medicamentos. Diário Oficial da União, 22 de maio de 2012.
  • 2
    AMERICAN PUBLIC HEALTH ASSOCIATION (APHA). Standard Methods for the Examination of the Water and Wastewater. 19th ed. New York: 1995.
  • 3
    FERNANDES A. S. G.; LEAL A. C. Lítio e sua aplicação terapêutica na psicose maníaco-depressiva. Ciências Farmacêuticas da Faculdade de Farmácia de Lisboa, 2002.
  • 4
    GOODWIN, F. K. Rationale for long-term treatment of bipolar disorder and evidence for long-term lithium treatment. J Clin Psychiatry, v. 63, suppl. 10, p. 10-12, 2002.
  • 5
    GOODWIN, G. M. Evidence-based guidelines for treating bipolar disorder: revised second edition - recommendations from the British Association for Psychopharmacology. J Psychopharmacol, v. 23, n. 4, p. 346-88, 2009.
  • 6
    INSTITUTO NACIONAL DE METROLOGIA (INMETRO). Orientação sobre validação de métodos analíticos. DOQ_CGCRE-008, revisão 3, 2010.
  • 7
    KAPCZINSKI, F. et al. Tratamento farmacológico do transtorno bipolar: as evidências de ensaios clínicos randomizados. Rev Psiq Clín, v. 32, suppl 1, p. 34-38, 2005.
  • 8
    MICHELON, L.; VALLADA, H. Fatores genéticos e ambientais na manifestação do transtorno bipolar. Rev Psiq Clín, v. 32, suppl 1, p. 21-27, 2005.
  • 9
    PASSARELI, M. M. Saliva como controle terapêutico do lítio. São Paulo, 1987. Tese (doutoramento) - Universidade de São Paulo.
  • 10
    ROSA, A. R. et al. Monitoramento de adesão ao tratamento com lítio. Rev Psiq Clín, v. 33, n. 5, p. 249-61, 2006.
  • 11
    SCOTT, J.; POPE, M. Nonadherence with mood stabilizers: prevalence and predictors. J Clin Psychiatry, v. 63, n. 5, p. 384-90, 2002.
  • 12
    SPROULE, B. Lithium in bipolar disorder: can drug concentrations predict therapeutic effect? Clin Pharmacokinet, v.41, n. 9, p. 639-60, 2002.

Publication Dates

  • Publication in this collection
    Feb 2014

History

  • Received
    23 Mar 2013
  • Reviewed
    21 Sept 2013
  • Accepted
    27 Sept 2013
Sociedade Brasileira de Patologia Clínica, Rua Dois de Dezembro,78/909 - Catete, CEP: 22220-040v - Rio de Janeiro - RJ, Tel.: +55 21 - 3077-1400 / 3077-1408, Fax.: +55 21 - 2205-3386 - Rio de Janeiro - RJ - Brazil
E-mail: jbpml@sbpc.org.br