Resumo em Inglês:

Bovine pericardium bioprosthesis has become a commonly accepted device for heart valve replacement. Present practice relies on the measurement of shrinkage temperature, observed as a dramatic shortening of tissue length. Several reports in the last decade have utilized differential scanning calorimetry (DSC) as an alternative method to determine the shrinkage temperature, which is accompanied by the absorption of heat, giving rise to an endothermic peak over the shrinkage temperature range of biological tissues. Usually, freeze-drying microscope is used to determine collapse temperature during the lyophilization of solutions. On this experiment we used this technique to study the shrinkage event. The aim of this work was to compare the results of shrinkage temperature obtained by DSC with the results obtained by freeze-drying microscopy. The results showed that both techniques provided excellent sensitivity and reproducibility, and gave information on the thermal shrinkage transition via the thermodynamical parameters inherent of each method.

Resumo em Inglês:

Magnesium is potentially useful for orthopaedic and cardiovascular applications. However, the corrosion rate of this metal is so high that its degradation occurs before the end of the healing process. In industrial media the behaviour of several magnesium alloys have been probed to be better than magnesium performance. However, the information related to their corrosion behaviour in biological media is insufficient. The aim of this work is to study the influence of the components of organic fluids on the corrosion behaviour of Mg and AZ31 and LAE442 alloys using potentiodynamic, potentiostatic and EIS techniques. Results showed localized attack in chloride containing media. The breakdown potential decreased when chloride concentration increased. The potential range of the passivation region was extended in the presence of albumin. EIS measurements showed that the corrosion behaviour of the AZ31 was very different from that of LAE442 alloy in chloride solutions.

Resumo em Inglês:

Biomaterials failures are frequently associated to the formation of bacterial biofilms on the surface. The aim of this work is to study the adhesion of non motile bacteria streptococci consortium and motile Pseudomonas fluorescens. Substrates with micro and nanopatterned topography were used. The influence of surface characteristics on bacterial adhesion was investigated using optical and epifluorescence microscopy, scanning electron microscopy (SEM) and atomic force microscopy (AFM). Results showed an important influence of the substratum nature. On microrough surfaces, initial bacterial adhesion was less significant than on smooth surfaces. In contrast, nanopatterned samples showed more bacterial attachment than the smooth control. It was also noted a remarkable difference in morphology, orientation and distribution of bacteria between the smooth and the nanostructured substrate. The results show the important effect of substratum nature and topography on bacterial adhesion which depended on the relation between roughness characteristics dimensions and bacterial size.

Resumo em Inglês:

The effect of the method of sterilization on the physical, chemical and mechanical properties of a new bone repairing material was studied. The material was obtained by thermal hydrolysis of beta-tricalcium phosphate/orthophosphoric acid cement and was composed of calcium deficient hydroxyapatite, octacalcium phosphate (OCP), and beta-tricalcium phosphate. Partial decomposition of the OCP was observed after sterilization for the three methods. Decomposition increased to the following sequence of sterilization methods: ethylene oxide; autoclaving; dry oven. On the other hand, mechanical strength decreased with regard to non sterilized material in the sterilization sequence: ethylene oxide; dry oven; autoclaving. The compressive strength was 8.5 ± 1.0; 9.0 ± 1.2; 8.2 ± 0.8 and 6.5 ± 1.0 MPa, whereas diametral tensile strength was 2.1 ± 0.3; 2.5 ± 0.1; 1.9 ± 0.9 and 1.6 ± 0.3 for the material sterilized by ethylene oxide, dry oven, and autoclaving, respectively. Several compositional and microstuctural changes were detected after dry heat and autoclave sterilization. Ethylene oxide sterilization had lesser effect on the chemical composition and strength than dry heat and autoclaving.

Resumo em Inglês:

Tissue engineering has evolved from the use of biomaterials for bone substitution that fulfill the clinical demands of biocompatibility, biodegradability, non-immunogeneity, structural strength and porosity. Porous scaffolds have been developed in many forms and materials, but few reached the need of adequate physical, biological and mechanical properties. In the present paper we report the preparation of hybrid porous polyvinyl alcohol (PVA)/bioactive glass through the sol-gel route, using partially and fully hydrolyzed polyvinyl alcohol, and perform structural characterization. Hybrids containing PVA and bioactive glass with composition 58SiO2-33CaO-9P2O5 were synthesized by foaming a mixture of polymer solution and bioactive glass sol-gel precursor solution. Sol-gel solution was prepared from mixing tetraethoxysilane (TEOS), triethylphosphate (TEP), and calcium chloride as chemical precursors. The hybrid composites obtained after aging and drying at low temperature were chemically and morphologically characterized through infrared spectroscopy and scanning electron microscopy. The degree of hydrolysis of PVA, concentration of PVA solution and different PVA-bioglass composition ratios affect the synthesis procedure. Synthesis parameters must be very well combined in order to allow foaming and gelation. The hybrid scaffolds obtained exhibited macroporous structure with pore size varying from 50 to 600 µm.

Resumo em Inglês:

Bone ingrowth requires materials with the existence of open and interconnected pores with diameters larger than 150 µm for proper circulation of nutrients. Such materials must possess enough mechanical strength to avoid failure whilst offering a bioactive surface for bone regeneration. We have developed porous ceramic alumina scaffold with compressive strength that achieves 3.3 MPa by replication method by using the network structure of cellular polymer foam. However, the biocompatibility of ceramics based on Al2O3 requires further improvement so that it could have strong bonding to natural bone tissue. To address this problem of the interface between alumina and bone, we have developed a novel calcium phosphate with Zn2+ (CaP-Zn) coating onto porous alumina ceramic scaffold by impregnating with calcium phosphate/poly(vinyl alcohol) slurry. The tri-dimensional alumina scaffold coated with CaP-Zn was extensively characterized by SEM, EDS and FTIR.

Resumo em Inglês:

Our hypothesis is that the action of aggregating and disaggregating substances in the blood can be detected and quantified by the Microplate Reader. To ascertain the validity of this hypothesis, we selected two types of blood: one that naturally presents erythrocyte aggregation (pig blood) and the other that does not present aggregation (bovine blood). One important reason for the choice of pig blood is that its erythrocyte aggregation resembles that of human blood. T. infestans saliva was added to the pig blood as a disaggregating substance, while bovine fibrinogen was added to the bovine blood as a substance that promotes erythrocyte aggregation. We investigated the dynamic viscosity (h) of these mammals' blood, of T. infestans saliva and of the absorption (A) by Microplate Reader, carrying out UV-Vis spectrophotometric assays of pig plasma with different concentrations of triatominae saliva and of bovine blood with different concentrations of fibrinogen. Our findings indicate that spectroscopic techniques such as the Microplate Reader complement and expand the study of blood rheology, erythrocyte sedimentation and aggregation.

Resumo em Inglês:

This work describes the process for functionalization of laponite through the grafting of 3-mercaptopropyltrimethoxysilane (MPTS). Laponite is synthetic smectite clay with surface area of 350 m²/g. The samples, prior to and after functionalization, were characterized by chemical analyses, thermogravimetric analysis (TGA), x ray diffraction (XRD), diffuse reflectance infrared Fourier transform spectroscopy (DRIFT), scanning electron microscopy and energy dispersive spectrometry (MEV/EDS). Infrared spectroscopy and elemental analyses confirmed the presence of organic chains and thiol groups in the modified clay. The immobilized and available thiol group, measured according to the Volhard method, totaled 1.4 meq/g of clay, with approximately 90% accessible for Ag+ trapping. These results represent an improvement as compared to other works concerning the functionalization of smectite-type clays in which the effect produced by functional group blockage limits the access of species to less than 10% of the complexing sites.

Resumo em Inglês:

Poly(vinyl alcohol) (PVA) hydrogels were obtained by freezing (-22 °C) and thawing (+25 °C) process, resulting in a semi-interpenetrating polymer network (s-IPN) with a sulfonated polyester (PES). The cryo-gels samples were analysed in terms of its water uptake capacity (WU) as a function of pH, temperature and ionic strength. WU of all samples were relatively high, and they showed a reasonable sensitivity to both pH and ionic strength. The pH- and ionic strength dependence is attributed to the dissociation of ionizable groups of PES. The degrees of crystallinity of the cryo-gels, determined by using differential scanning calorimetry (DSC), are lower than pure PVA. Besides, decrease of glass transition temperature (Tg) of the samples when compared with pure PVA was observed. This results are due interactions between PVA and PES, which lead to an increase on the amorphous content of the hydrogels. Our results show that, despite of changes in the microstructure of the hydrogels due the presence of the polyelectrolyte, the cryo-gels reveal a long-term stability.

Resumo em Inglês:

InCeram (Vita Zahnfabrik- Germany) is known as a high strength ceramic being used for core crowns and for fixed partial denture frameworks. InCeram system consists of slip-casting technique which is used for to build the framework, which is then pre-sintered obtaining an open-pore microstructure. The material gains its strength by infiltration of the lanthanum glass into the porous microstructure. In this work, commercial alumina (Al2O3), alumina-zirconia (Al2O3-ZrO2) and glasses lanthanum oxide-rich powders, used in InCeram system, were characterized, using x ray diffraction, dilatometry and scanning electron microscopy. The characteristics of these powders were related aiming to consider their substitution for new ceramic materials.

Resumo em Inglês:

A study was made of the influence of ionic strength (S) on the apparent (AV) and plastic (PV) viscosities and water loss (WL) of sodium bentonite suspension with polymers. Na-bentonite was dispersed in water (4.86% w/w) of different ionic strengths (S = 0.0, 0.015, 0.030 and 0.045 M) followed by the addition of polymer. Three polymer samples were studied, i.e., low viscosity carboxymethyl cellulose (CMC BV), polyanionic cellulose (PAC), and partially hydrolyzed polyacrylamide (HPAM). The results indicated that the presence of salts and increased salinity greatly influence the apparent and plastic viscosities and water loss of bentonite suspensions with polymer.

Resumo em Inglês:

alpha-tocopherol was encapsulated in a glassy food model based on solution of maltodextrin (DE 20) and gelatin, through the use of quick freeze and freeze-drying procedures. The ratio of the maltodextrin, alpha-tocopherol and gelatin was 3:2:1 respectively. The morphology of the glassy food model was observed by scanning electron microscopy, whose analyses showed a slightly smooth surface and a rather fragile and porous structure due to cavities formed by ice crystals during freezing, and the absence of crystalline structure. It was observed by x ray diffraction that the material is an amorphous state. The samples stored in a specific plastic vessel isolated from gas and light held its amorphous state with no variations that concern to morphology and keeping 100% of the encapsulated alpha-tocopherol up to 90 days at 25 and 35 °C.

Resumo em Inglês:

The objective of this study was to investigate how mechanical surface treatments performed for removal of excess of molten glass, influence the fracture toughness of a dental zirconia toughened alumina (In-Ceram® Zirconia). Infiltrated ZTA disks were submitted to three different surface treatments (grinding, sandblasting and grinding + sandblasting + annealing). Fracture toughness was accessed through indentation strength test (IS). X ray diffraction was used to investigate the metastability of tetragonal zirconia particles under all treatments proposed. Kruskall-Wallis non-parametrical test and Weibull statistics were used to analyze the results. Grinding (group 1) introduced defects which decreased the fracture toughness and reliability, presenting the lowest K IC. On the other hand, grinding followed by sandblasting and annealing (group 3) presented the highest K IC. Sandblasting (group 2) presented the highest reliability but lower K IC compared to group 3.

Resumo em Inglês:

It is of a great importance to know binders' viscosity in order to perform handling, mixing, application processes and asphalt mixes compaction in highway surfacing. This paper presents the results of viscosity measurement in asphalt-rubber binders prepared in laboratory. The binders were prepared varying the rubber content, rubber particle size, duration and temperature of mixture, all following a statistical design plan. The statistical analysis and artificial neural networks were used to create mathematical models for prediction of the binders viscosity. The comparison between experimental data and simulated results with the generated models showed best performance of the neural networks analysis in contrast to the statistic models. The results indicated that the rubber content and duration of mixture have major influence on the observed viscosity for the considered interval of parameters variation.

Resumo em Inglês:

The structure of mullite obtained by thermal decomposition of topaz at 1340 °C and after additional thermal treatment at 1600 °C was characterized by 29Si and 27Al MAS NMR spectroscopy and x ray diffraction. No amorphous phase was detected by these techniques. The 29Si MAS NMR spectra of the mullite samples showed four resonance peaks at -81, -86, -90 and -94 ppm. The peak at -81 ppm corresponded to silicon near oxygen vacancies in the mullite structure. The peak at 86 ppm was related to a sillimanite-type site and was the major contribution, ranging from 42 to 50%. The two other peaks, at -90.0 ppm and -94 ppm, were interpreted as resulting from rearrangements of the sillimanite-type site by the replacement of AlO4 by SiO4 tetrahedra16. The 27Al MAS NMR data of the two samples exhibited three different peaks, two of which were attributed to tetrahedral sites at 40 -45 and 63 -67 ppm, while the third was assigned to an octahedral site at about -6 ppm. The ratio of tetrahedral to octahedral aluminum sites was found to depend on the temperature applied during the preparation of the mullite and was higher at 1600 °C.

Resumo em Inglês:

This study investigated the influence of ethanol concentration on softening tests for cross-link density evaluation (microhardness) of dental composites. Specimens of Filtek Z100 (3M ESPE) were light-activated by standard or pulse-delay methods. After initial Knoop hardness readings (KHN1), half of specimens (n = 10) for each irradiation method was stored in 100% ethanol, and half in 75% ethanol, during 24 hours, and hardness was determined anew. Hardness deterioration (DKHN) was recorded as the difference between pre and post-storage values. KHN1 data were submitted to one-way ANOVA and Tukey's test (alpha = 0.05), and hardness deterioration was analyzed by two-way ANOVA and Tukey's test (alpha= 0.05). For KHN1, no significant differences were detected between the activation modes (p = 0.697). Samples light-activated by the pulse-delay method presented significantly higher softening compared to the standard mode when samples were immersed in 100% ethanol. Conversely, no significant differences between curing modes were detected for samples stored in 75% ethanol.

Resumo em Inglês:

This paper deals with the effect of silica fume and styrene-butadiene latex (SBR) on the microstructure of the interfacial transition zone (ITZ) between Portland cement paste and aggregates (basalt). Scanning Electron Microscope (SEM) equipped with energy dispersive x ray analysis system (EDX) was used to determine the ITZ thickness. In the plain concrete a marked ITZ around the aggregate particles (55 µm) was observed, while in concretes with silica fume or latex SBR the ITZ was less pronounced (35-40 µm). However, better results were observed in concretes with silica fume and latex SBR (20-25 µm).

Resumo em Inglês:

Samples of unalloyed iron were sintered in the presence of an abnormal glow discharge using a confined anode-cathode configuration. The samples were placed on a holder acting as the discharge anode inside an AISI 1020 steel hollow cathode. Heating of the outer cathode was obtained by the bombardment of ions and energetic neutral particles. As a consequence of the confined geometry, the sample was efficiently heated mainly by radiation from the cathode. In order to evaluate the results of the sintering process by plasma, samples of unalloyed iron were also sintered in a resistive furnace using the same thermal cycle. The porosity, dimension and morphology of the pores were characterized by means of four basic parameters: area fraction, mean diameter, shape factor and elongation factor. The results show that the shape factor depends on the pore size, a characteristic that was not observed for elongation factor. For samples sintered in plasma reactor or conventional furnace, no significant difference in the porosity or in the pores morphology was observed.

Resumo em Inglês:

It is a known fact that the adequate combination of components and experimental conditions may produce materials with specific requirements. This study presents the effect of carbon fiber fabric impregnation with polyaniline conducting polymer aiming at the radar absorbing material processing. The experiments consider the sample preparation with one and two impregnations. The prepared samples were evaluated by reflectivity measurements, in the frequency range of 8-12 GHz and scanning electron microscopy analyses. The correlation of the results shows that the quantity of impregnated material influences the performance of the processed microwave absorber. This study shows that the proposed experimental route provides flexible absorbers with absorption values of the incident radiation close to 87%.