Resumo em Inglês:

Theoretical analysis of formation energy and geometry was done to compare the relative stabilities of modified carbon nanostructures representative fragments. Structure and energies of formation were calculated at semiempirical level of theory. Depending of B-N pair localization on the molecular structures the formation enthalpy decreases. B-N substitution in tubular structures at low concentration decreases the energy when the tubes have small diameters. Our results are in according to experimental works which have shown that boron and nitrogen are met at region of defects in B X C Y N Z nanostructures.

Resumo em Inglês:

Industry has been challenged to provide riser systems which are more cost effective and which can fill the technology gaps with respect to water depth, riser diameter and high temperatures left open by flexibles, steel catenary risers (SCRs) and hybrid risers. Composite materials present advantages over conventional steel risers because composite materials are lighter, more fatigue and corrosion resistant, better thermal insulators and can be designed for improving the structural and mechanical response. This paper contains a study of the toughening mechanism of an epoxy resin under rubber addition by means of fractographic analysis and its relation with the fracture process and increase of strength of a composite riser employing this polymeric matrix. Initially, an epoxy resin system was toughened by rubber CTBN addition (10 wt. (%)) as a way of improving the flexibility of future risers. Mechanical and thermal analyses were carried out for characterizing the polymeric systems. Later, composite tubes were prepared and mechanically characterized. The influence of matrix toughening on the mechanical behavior of the tubes was also studied. Split-disk tests were used to determine the hoop tensile strength of these specimens. The results indicate that the matrix plays an important role in composite fracture processes. The adding rubber to the polymeric matrix promoted a simultaneous increase of stress and elongation at fracture of the tubes manufactured herein, which is not often reported. These results, probably, is function of better adhesion between fibers and polymeric matrix observed in the CTBN-modified composite rings, which was evidenced in the fractografic analysis by SEM after the split-disk tests.

Resumo em Inglês:

In the present study, flexural strength together with pore structure, thermal behavior and microstructure of concrete containing ground granulated blast furnace slag with different amount of ZnO2 nanoparticles has been investigated. Portland cement was replaced by different amounts of ground granulated blast furnace slag and the properties of concrete specimens were investigated. Although it negatively impact the properties of concrete, ground granulated blast furnace slag was found to improve the physical and mechanical properties of concrete up to 45 wt. (%). ZnO2 nanoparticles with the average particle size of 15 nm were added partially to concrete with the optimum content of 45 wt. (%) of ground granulated blast furnace slag and physical and mechanical properties of the specimens was measured. ZnO2 nanoparticle as a partial replacement of cement up to 3 wt. (%) could accelerate C-S-H gel formation as a result of increased crystalline Ca(OH)2 amount at the early age of hydration and hence increase flexural strength of concrete. The increased the ZnO2 nanoparticles' content more than 3 wt. (%), causes the reduced the flexural strength because of the decreased crystalline Ca(OH)2 content required for C-S-H gel formation together with unsuitable dispersion of nanoparticles in the concrete matrix. ZnO2 nanoparticles could improve the pore structure of concrete and shift the distributed pores to harmless and few-harm pores.

Resumo em Inglês:

In this work, strength assessments and percentage of water absorption of high performance self compacting concrete containing different amounts of ground granulated blast furnace slag and CuO nanoparticles as binder have been investigated. Portland cement was replaced by different amounts of ground granulated blast furnace slag and the properties of concrete specimens were investigated. Although it negatively impacts the physical and mechanical properties of concrete at early age of curing, ground granulated blast furnace slag was found to improve the physical and mechanical properties of concrete up to 45 wt. (%) at later ages. CuO nanoparticles with the average particle size of 15 nm were partially added to concrete with the optimum content of ground granulated blast furnace slag and physical and mechanical properties of the specimens were measured. CuO nanoparticle as a partial replacement of cement up to 3.0 wt. (%) could accelerate C-S-H gel formation as a result of increased crystalline Ca(OH)2 amount at the early age of hydration and hence increase strength and improve the resistance to water permeability of concrete specimens. The increased the CuO nanoparticles' content more than 3.0 wt. (%), causes the reduced the split tensile strength because of the decreased crystalline Ca(OH)2 content required for C-S-H gel formation. Several empirical relationships have been presented to predict flexural and split tensile strength of the specimens by means of the corresponding compressive strength at a certain age of curing. More rapid appearance of the peaks related to hydrated products in X-ray diffraction results, all indicate that CuO nanoparticles could improve mechanical and physical properties of the concrete specimens.

Resumo em Inglês:

Electrospinning has been recognized as an efficient technique for the forming of polymer nanofibers. Silk fibroin (SF) nanofibers were electrospun from SF solution using trifluoroacetic acid solution as a solvent. In the present work, we have systematically evaluated the effects of instrument parameters, including applied voltage, tip-target distance, solution flow rate, solution parameters; such as polymer concentration and solution viscosity on the morphology of electrospun SF fibers. The applied voltage and flow rate was monitored at fixed tip target distance during the electrospinning process and it was correlated with the characteristics of the fibers obtained. The number of deposited fibers also increases with the applied voltage. Also, viscosity, flow rate and applied voltage strongly affect the shape and morphology of the fibers. A particular interest, we demonstrated that by monitoring the applied voltage and flow rate it is possible to control the fibers morphology and bead concentration. Rheological study showed a strong dependence of spinnability and fiber morphology on solution viscosity. Solution concentrations has been found to most strongly affect fiber size, with fiber diameter increasing with increasing solution concentration and the morphology of the deposition on the collector changed from spherical beads to interconnected fibrous networks. FTIR analysis clearly shows that there are no spectral differences between fibers and which suggests that there was no chemical modification developed during the process. Under optimized conditions, homogenous (not interconnected) SF fibers with a mean diameter of 234 nm were prepared.

Resumo em Inglês:

The sustainable management of solid wastes stimulates metallurgic and metal mechanics industries to look for safety applications for these wastes. The present paper examines the fracture behavior of polymer concrete (PC) manufactured with recycled foundry waste in substitution of fresh one. The recycled foundry sand is contaminated with polymer resin from the mold making process. Epoxy and unsaturated polyester resins were used as binder as cement substitute. The fracture results are analyzed by fracture energy; Gf, fracture toughness, K Ic, and the crack tip opening displacement, CTOD. It is found that the use of recycled foundry sand significantly influences the fracture properties. The use of recycled sand increase fracture toughness and similar fracture energy is observed. These results show that recycled sand is an excellent alternative as raw material.

Resumo em Inglês:

The increasing use of titanium alloys as biomaterials can be attributed, among other factors, to their low Young modulus compared to other alloys with similar mechanical strength. However, Ti-6Al-4V alloy, the alloy most widely used in implants, has a stiffness of about 110 GPa, which is much higher than the typical stiffness of 20 GPa of human bone. In the specific case of hip arthroplasty, this difference in stiffness reduces the load imposed on the femur through the stress shielding phenomenon, which, in the medium term, usually results in the loss of bone density. One way to reduce this phenomenon is by using TiNbTaZr (TNTZ) alloys, which have a stiffness of about 47 GPa. This work uses numerical simulation to evaluate the effectiveness of TNTZ laser coated on a Ti-6Al-4V hip prosthesis in reducing stress shielding. The results show that this may improve the performance of the prosthesis, extending its service life.

Resumo em Inglês:

As a technique, Equal Channel Angular Pressing (ECAP) is simple and inexpensive. However, if die manufacture and operational details are not carefully planned and implemented, difficulties arise, which can interfere with the product characteristics and the pressing operation itself. The present paper offers guidelines on die design and manufacture, emphasizing geometry, material and heat treatment. Further, operational parameters such as lubrication, pressing temperature, deformation routes, die closure procedure and the influence of channel cross section on maximum acceptable load are described. Additionally, the effects of those variables on the product characteristics (deformation level and homogeneity) and integrity, plus process control and safety, are discussed.

Resumo em Inglês:

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) - PHBV is a biodegradable polyester which has been studied as an option for the production of disposable goods. Attapulgite is a fibrous clay mineral. The aim of this work was to produce and characterize renewable resource derived-nanocomposites based on PHBV and organophilic attapulgite (MAT). The nanocomposites were characterized by XRD, SEM and thermal analysis. It was observed reduction in degree of crystallinity, in melting and glass transition temperatures and in thermal stability of polymer due to the addition of clay to PHBV matrix. The best results were obtained for PHBV films containing 3 and 5% MAT. These films presented a slight increase in processing window and decrease in crystalline temperature and in degree of crystallinity as compared to pure PHBV.

Resumo em Inglês:

Resin Transfer Molding (RTM) is largely used for the manufacturing of high-quality composite components and the key stage during processing is the resin infiltration. The complete understanding of this phenomenon is of utmost importance for efficient mold construction and the fast production of high quality components. This paper investigates the resin flow phenomenon within the mold. A computational application was developed to track the resin flow-front position, which uses a finite volume method to determine the pressure field and a FAN (Flow Analysis Network) technique to track the flow front. The mass conservation problem observed with traditional FE-CV (Finite Element-Control Volume) methods is also investigated and the use of a finite volume method to minimize this inconsistency is proposed. Three proposed case studies are used to validate the methodology by direct comparison with analytical and a commercial software solutions. The results show that the proposed methodology is highly efficient to determine the resin flow front, showing an improvement regarding mass conservation across volumes.

Resumo em Inglês:

Nitric oxide (NO) is a diffusible messenger that has been involved in numerous physiological processes ranging from vasodilatation and antimicrobial properties to wound healing. The beneficial effects can be attributed to the role NO plays in angiogenesis, inflammation and tissue remodeling. In the present work, a polymeric device for the sustained site specific delivery of nitric oxide using a latex rubber matrix from Hevea brasiliensis which encapsulates the spin trap iron(II)- diethyldithiocarbamate complex (FeDETC) was developed. The release profiles of NO from latex rubber matrix were studied and stability studies were carried out. Electron Paramagnetic Resonance (EPR) signal of NO was detected in the membrane exposed to ambient atmosphere at room temperature (25 °C) even after 350 hours. FTIR spectroscopy data indicated that NO-FeDETC retained its structural and spectroscopic properties upon encapsulation in the latex matrix. The NO delivery system developed in this work as a membrane, presented high stability.

Resumo em Inglês:

Polypropylene matrix composites reinforced with treated coconut fibers were produced. Fibers chemically treated (alkalization-CCUV samples) or mechanically treated (ultrasonic shockwave-CMUV samples) were dried using UV radiation. The goal was to combine low cost and eco-friendly treatments to improve fiber-matrix adhesion. Composite samples containing up to 20 vol. (%) of untreated and treated coconut fibers were taken from boxes fabricated by injection molding. Water absorption and mechanical properties were investigated according to ASTM D570-98 and ASTM D638-03, respectively. Electrical characterizations were carried out to identify applications of these composites in the electrical sector. NBR 10296-Electrical Tracking Standard (specific to industry applications) and conductivity measurements were obtained applying 5 kV DC to the samples. CMUV samples containing 5 vol. (%) fiber presented superior tensile strength values (σ~28 MPa) compared to the untreated fibers composite (σ~22 MPa) or alkali treatment (σ~24 MPa). However, CMUV composites containing 10 vol. (%) fiber presented best results for the electrical tracking test and electrical resistivity (3 × 10(7) Ω.m). The results suggest that composites reinforced with mechanically treated coconut fibers are suitable for electrical applications.

Resumo em Inglês:

This study aims to use electrodes modified with bismuth films for the determination of zinc and cadmium. The film was electrodeposited ex situ on a composite carbon electrode with polyurethane and 2% metallic bismuth (2BiE) and on a carbon bar electrode (CBE). The electrodes were characterized by scanning electron microscopy and energy dispersive spectroscopy. Through differential pulse anodic stripping voltammetry, the electrodes 2BiE and CBE containing bismuth films showed a limit of detection (LOD) of 5.56 × 10-5 and 3.07 × 10-5 g.L-1 for cadmium and 1.24 × 10-4 and 1.53 × 10-4 g.L-1 for zinc, respectively. The presence of a bismuth film increased the sensitivity of both electrodes.

Resumo em Inglês:

Thermal aging of hydroxy-terminated polybutadiene/isophorone diisocyanate (HTPB/IPDI)-based polyurethane was studied as a function of NCO/OH ratio (1.0 and 0.85). Samples were aged in air ovens at 50, 60, 65, and 70 ºC for periods of time from 1 to 34 weeks. Changes in chemical (swelling testing and FT-IR spectroscopy) and mechanical (tension testing and hardness) properties were evaluated throughout the aging assays. Correlation between equilibrium swelling ratio and elastic modulus, coupled with changes in FT-IR spectra, indicated oxidative cross-linking as the dominant mechanism for both molar ratios investigated. However, determination of Arrhenius activation energy resulted in values of (82 ± 10) kJ.mol-1 and (156 ± 30) kJ.mol-1 for 1.0 and 0.85 NCO/OH ratios, respectively, thus revealing faster oxidative degradation kinetics for higher urethane linkage networks.

Resumo em Inglês:

The crystal structure of a synthetic AB-type carbonate apatite sample was analyzed by Rietveld refinement including a model with carbon atom not fixed in the B-site of the apatite structure. Only one constraint was applied to this model: the fractional occupancies of the atoms in the CO3 ion plus PO4 ion were equal 1.0 per phosphate site with six sites per unit cell. Rietveld refinement of the crystal structure with space group P6(3)/m results in cell parameters a = 9.3583(1) Å and c = 6.9226(5) Å; Z =1; Rwp = 0.0824 and 9.5 wt. (%) of carbonate in this structure. The use of simple geometry formulas showed that the C atom is not located at the center of the equilateral triangle of oxygen O2, O3 and O3', but to a distance 0.18 Å of this triangle. The results seem to indicate a new 3-D crystal structure of the carbonated apatite in PO4 groups.

Resumo em Inglês:

Arc discharge is the most practical method for the synthesis of single wall carbon nanotubes (SWCNT). However, the production of SWCNT by this technique has low selectivity and yield, requiring further purification steps. This work is a study of purification of SWCNT by heat treatment in an inert atmosphere followed by supercritical fluid extraction. The raw arc discharge material was first heat-treated at 1250 °C under argon. The nanotubes were further submitted to an extraction process using supercritical CO2 as solvent. A surfactant (tributylphosphate, TBP) and a chelating agent (hexafluoroacetylacetone, HFA) were used together to eliminate metallic impurities from the remaining arc discharge catalysts. Analysis of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) showed an efficient removal of iron and cobalt (>80%). The purified nanotubes were further analyzed by TGA and Raman spectroscopy.

Resumo em Inglês:

Titanium-based composites with in-situ calcium and phosphor phases were prepared by powder metallurgy processing with titanium and hydroxyapatite (HA) powders. The mixtures were performed in a friction mill with alcohol for 5 hours, dried in a rotating evaporator, pressed at 600 MPa and sintered at 1200 ºC for 2 hours in argon atmosphere. Crystal phases of the as-fabricated composite are found to be, α-Ti, CaTiO3, Ca3(PO4)2 and Ti xPy phase(s). The analyses revealed that titanium particles were covered with a compact layer of Ti xPy and CaTiO3 phases, which resulted from the decomposition of HA into CaTiO3 and β-Ca3(PO4)2 at approximately 1025 ºC. Then the reactions were followed by the decomposition of β-Ca3(PO4)2, resulting in the growth of CaTiO3 layer and in the nucleation and growth of Ti xPy phase(s).

Resumo em Inglês:

In this paper nuclear techniques were used to describe the structural characteristics of ceramic samples. These samples were produced mainly with silica to simulate sandstones. Three sets of samples with different characteristics were analyzed using gamma ray transmission to obtain point by point porosity and X-ray microtomography to obtain the porosity, for 2D sections and the scanned bulk, as well as the pore size distribution. The transmission results indicated total porosity values of 28.6 (4.5)% for the group of samples called ceramic I and 59.6 (2.1)% for ceramic II. The samples analyzed by microtomography achieved resolutions of 1.7, 0.6 and 1.3 μm for the ceramic I, II, and III samples, respectively. This analysis indicated average porosity values of 27.9 (1.4)% for ceramic I samples and 29.4 (1.2)% for ceramic III samples.

Resumo em Inglês:

Vertically aligned carbon nanotubes were successfully grown on flexible carbon fibers by plasma enhanced chemical vapor deposition. The diameter of the CNT is controllable by adjusting the thickness of the catalyst Ni layer deposited on the fiber. Vertically aligned nanotubes were grown in a Plasma Enhanced Chemical Deposition system (PECVD) at a temperature of 630 ºC, d.c. bias of -600 V and 160 and 68 sccm flow of ammonia and acetylene, respectively. Using cyclic voltammetry measurements, an increase of the surface area of our electrodes, up to 50 times higher, was observed in our samples with CNT. The combination of VACNTs with flexible carbon fibers can have a significant impact on applications ranging from sensors to electrodes for fuel cells.

Resumo em Inglês:

In this paper the influence of calcination temperature on the corrosion resistance of a Ti/SnO2-Sb electrode prepared according to Pechini's method and its efficiency for phenol oxidation in chloride medium were investigated. When calcination was performed at 600 °C tin distribution throughout the film was more uniform, providing a more homogeneous film structure. Electrolysis of a 0.34 mol.L-1 NaCl solution containing 100 mg.L-1 phenol at 10 mA.cm-2 for 30 minutes lead to corrosion of the electrodes calcined at 400 and 500 °C, whereas the one calcined at 600 °C remained practically unchanged, indicating that the coating structure, which is dependent of calcination temperature, plays an important role on the structural integrity of electrode material. Phenol concentration was reduced in 90% with the Ti/SnO2-Sb electrode calcined at 600 °C after 60 minutes of electrolysis at 10 mA.cm-2.

Resumo em Inglês:

Interest in laser beam welding for aerospace applications is continuously growing, mainly for aluminum alloys. The joints quality is usually assessed by non-destructive inspection (NDI). In this work, bead on plate laser welds on 1.6 mm thick AA6013 alloy sheets, using a 2 kW Yb-fiber laser were obtained and inspected by pulse/echo ultrasonic phased-array technique. Good and poor quality welds were inspected in order to verify the limits of inspection, comparing also to X-ray radiography and metallographic inspections. The results showed that ultrasonic phased array technique was able to identify the presence of grouped porosity, through the attenuation of the amplitude of the echo signal. This attenuation is attributed to the scattering of the waves caused by micro pores, with individual size below the resolution limit of the equipment, but when grouped, can cause a perceptive effect on the reflection spectra.

Resumo em Inglês:

Since the 1980s, different devices based on superelastic alloys have been developed to fulfill orthodontic applications. Particularly in the last decades several researches have been carried out to evaluate the mechanical behavior of Ni-Ti alloys, including their tensile, torsion and fatigue properties. However, studies regarding the dependence of elastic properties on residence time of Ni-Ti wires in the oral cavity are scarce. Such approach is essential since metallic alloys are submitted to mechanical stresses during orthodontic treatment as well as pH and temperature fluctuations. The goal of the present contribution is to provide elastic stress-strain results to guide the orthodontic choice between martensitic thermal activated and austenitic superelastic Ni-Ti alloys. From the point of view of an orthodontist, the selection of appropriate materials and the correct maintenance of the orthodontic apparatus are essential needs during clinical treatment. The present work evaluated the elastic behavior of Ni-Ti alloy wires with diameters varying from 0.014 to 0.020 inches, submitted to hysteresis tensile tests with 8% strain. Tensile tests were performed after periods of use of 1, 2 and 3 months in the oral cavity of patients submitted to orthodontic treatment. The results from the hysteresis tests allowed to exam the strain range covered by isostress lines upon loading and unloading, as well as the residual strain after unloading for both superelastic and thermal activated Ni-Ti wires. Superelastic Ni-Ti wires exhibited higher load isostress values compared to thermal activated wires. It was found that such differences in the load isostress values can increase with increasing residence time.