Resumo em Inglês:

A mix design procedure for high-performance concrete mixes has been presented in this paper. Since rheological parameters and compressive strength are fundamental properties of concrete in two different stages of production, the correlation between rheological parameters and compressive strength has been used instead of using water-cement ratio versus compressive strength relationship. Water-cement ratio and aggregate volume to paste volume ratio has also been determined from rheological behavior and used in the mix design. In the proposed method, the designer is able to estimate rheological parameters like yield stress and plastic viscosity at the design stage for a given target strength, in addition to ingredients of concrete.

Resumo em Inglês:

Multiferroic Pb(Fe2/3W1/3)O3-PbTiO3 (PFW-PT) ceramics were synthesized via a modified two-stage solid-state reaction. This method utilized Fe2WO6, prepared at a first-stage, which was subsequently reacted with a stoichiometric amount of PbO and TiO2 at the second stage. This procedure efficiently suppressed the formation of lead tungstates and leads to getting dense ceramics. Electric and dielectric properties of (1-x)Pb(Fe2/3W1/3)O3 -xPbTiO3 solid solutions were investigated as a function of the frequency and temperature. All samples present density higher than 96% of the theoretical one, low percentage of pyrochlore phase (<2%) and relatively high electrical resistivity (<10(10) Ω.m). RF dielectric measurements over the temperature showed the presence of a peak, which is related to the ferro-paraelectric phase transition and conductive contributions (in the range 200-700 K), associated to a electronic hoping mechanism. The dielectric properties of the PFW shows a typical relaxor behaviour for x = 0 and 0.10 with frequency-dependent peak temperature (Tm), while the samples with higher PT-content undergo a 'normal' para-ferroelectric transition at the Curie temperature T C.The FE phase transition of PFW is shifted to higher temperatures by PbTiO3 (PT) additions and high resistivity are obtained for PT containing samples. Different types of magnetic activity dependent on composition and temperature were found.

Resumo em Inglês:

Polymers are vastly employed for numerous purposes in different industrial segments and generate soaring quantities of discarding in the environment. This research analyzed the degradability/biodegradability of polypropylene films (PP) and Bioriented polypropylene (BOPP) polymers after 11 months interred in the São Giácomo landfill in Caxias do Sul. Comparing the buried PP film to a sample of virgin PP, two peaks of degrading activity appeared at the TG curve as well as structure modification typified by occurrence of new absorption bands at FTIR, which can be credited to changes in crystallinity. Thermal analysis carried out on the buried PP and BOPP showed decreases in the percentage of crystallinity due to chain scission. The major reduction was observed in the PP, since its crystallinity is a consequence of polymerization instead of chain orientation processes, as in BOPP. Cracks and erosion of the polymer surface were detected in both PP and BOPP, indicating degrading processes by microorganisms.

Resumo em Inglês:

A complete experimental investigation on the instantaneous strain-hardening behaviour of powder metallurgy preforms of Fe-0.35%C was carried out. The strain hardening behaviour of the above-mentioned P/M sintered steel preforms with aspect ratio of 0.4 and 0.6, respectively, under triaxial stress state condition was determined by cold upsetting under nil/no and graphite lubricant conditions. The instantaneous strain hardening value (n i), strength coefficient (Ki), and the stress as a function of strain and densification were obtained and analyzed. Further, a relation is obtained from a semi-log plot of stress against relative density. This was analyzed to study the hardening behaviour due to the densification as applied stress is a function of induced strain as well as of densification in the powder metallurgy materials.

Resumo em Inglês:

The aim of this work was to produce hydroxyapatite (HA) granules containing 0, 0.5, 1 and 5 mol. (%) of strontium (Sr), evaluate the physico-chemical properties and also the cytotoxicity by three different parameters of cell viability (ISO 10993-5, 10993-12). The physico-chemical characterization was carried out by using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR) and X-ray fluorescence (XRF). The XRD profile presented the main peaks of HA (JCPDS 860740) and the absorption bands of HA were identified by FTIR. The XRF results showed that the strontium concentration was close to the theoretical value. Regarding the cytotoxicity assays, the incorporation of strontium up to 5 mol. (%) to the HA did not affected dehydrogenase activity (XTT, 2,3-bis[2-methyloxy-4-nitro-5-sulfophenyl]-2H-tetrazolium-5-carboxanilide), membrane integrity (neutral red uptake) or DNA contend (incorporation of crystal violet), in relation to HA alone. In conclusion, hydroxyapatite containing from 0.5 to 5 mol. (%) of Sr was successfully produced and presented no cytotoxicity.

Resumo em Inglês:

Geometry and electronic structure of chiral carbon and carbon nitride (CNx) nanotubes were investigated through quantum chemical methods. Finite nanotubes with diameters ranging from 5 to 10 Å and containing up to 500 atoms were considered. CNx structures were built through random substitution of carbon atoms by nitrogen. The molecules were fully optimized by semi-empirical quantum chemical method (PM3). Our results show that the energy associated with nitrogen incorporation depends strongly upon the tube helicity and diameter. The doping of nanotubes with nitrogen contributes to reduce the stress caused by the small diameter of the studied systems. Density of States (DOS) results for pure carbon and CNx nanostructures, obtained through DFT and Hartree-Fock calculations, were analyzed. The introduction of nitrogen in the tube produce states in the gap region which characterizes the metallic behavior, as expected for these systems after N-doping.

Resumo em Inglês:

In order to study the influence of different sulfonation routes on its thermal and structural properties sulfonated polyaniline (SPAni) was prepared. FT-IR revealed that the formation of PAni salt or ring sulfonation depends on the route. UV-visible spectra pointed out that the level of the PAni protonation was dependent on the sulfonation route. A new approach was given for TG/DTG and DSC results correlating different energy levels with the distinguished sulfonation routes. The TG/DTG degradation steps and the amount of the released material corroborated the structural differences of the polyanilines. For each DSC first regime of heating, a broad and intense peak (from -30 to 250 ºC) with different level of energy was noticed. That peak could be ascribed to the multiple relaxations and breaking of the PAni intra and inter hydrogen bonds after sulfonation.

Resumo em Inglês:

The new Ca2CoTaO6 double perovskite has been synthesized by a conventional solid state reaction and its unit cell parameters determined by X-ray powder diffractometry. It crystallizes in the monoclinic space group P2(1)/n. The unit cell parameters are: a = 5.507(2) Å; b = 5.564(3) Å; c = 7.798(3) Å; β = 89.99(4)° and Z = 2. The IR spectrum of the material was recorded and is briefly discussed. Some comparisons with Ca2CoNbO6 and other isostructural perovskites are also performed.

Resumo em Inglês:

The addition of tricalcium silicate (C3S) to apatite cements results in an increase of bioactivity and improvement in the mechanical properties. However, adding large amounts raises the local pH at early stages, which retards the precipitation of hydroxyapatite and produces a loss of mechanical strength. The introduction of Pozzolanic materials in cement pastes could be an effective way to reduces basicity and enhance their mechanical resistance; thus, the effect of adding silica on the chemical, mechanical and biological properties of α-tricalcium phosphate/C3S cement was studied. Adding silica produces a reduction in the early pH and a decrease in setting times; nevertheless, the presence of more calcium silicate hydrate (C-S-H) delays the growth of hydroxyapatite crystals and consequently, reduces early compressive strength. The new formulations show a good bioactivity, but higher cytotoxicity than traditional cements and additions higher than 2.5% of SiO2 cause a lack of mechanical strength and an elevated degradability.

Resumo em Inglês:

The aim of this work is to report the performance of different supports for the immobilization of commercial porcine pancreatic lipase. The immobilization tests were carried out in several types of Accurel, activated alumina, kaolin, montmorillonite, ion exchange resins and zeolites. The characterization of the supports showed differences in terms of specific area and morphology. The characteristics of the supports influenced the amount of enzyme adsorbed, yield of immobilization and esterification activity of the resulting immobilized catalyst. The clays KSF and natural and pillared montmorillonites presented potential for use as support for lipase immobilization in terms of yield and esterification activity. Yields of immobilization of 76.32 and 52.01% were achieved for clays KSF and natural montmorillonite, respectively. Esterification activities of 754.03, 595.51, 591.88 and 515.71 U.g-1 were obtained for lipases immobilized in Accurel MP-100, Amberlite XAD-2, mordenite and pillared montmorillonite, respectively.

Resumo em Inglês:

There are evidences considering the effectiveness of Si on enhancing biological properties of calcium phosphates; however, there are not many works relating to the Si-alpha-TCP bone cement. The influence of silicon doping on the properties of Α-TCP cement was analyzed. Si-TCP was obtained by a solid state reaction employing CaCO3, CaHPO4 and CaSiO3 and powder was analyzed by XRD, FTIR, XRF and BET specific area. Cement samples were analyzed for their surface of fracture morphology, mechanical resistance and SBF bioactivity. Cement mechanical resistance was not satisfactory for biomedical application; nonetheless, sample's surface was coated by an apatite layer after immersion in SBF. Notwithstanding, to ensure that silicon is the element responsible for increasing the material's bioactivity it is necessary to evaluate the in vivo performance of the bone cement obtained in this work.

Resumo em Inglês:

Styrene-Butadiene-Rubber (SBR) is a synthetic rubber copolymer used to fabricate several products. This study aims to demonstrate the use of SBR as feedstock for carbon nanomaterials (nanofibers and nanotubes) growth, and therefore to establish a novel process for destination of waste products containing SBR. A three stage electrically heated flow reactor was used. Small pellets of rubber were pyrolyzed at a temperature of 1000 ºC. The pyrolyzates were mixed with oxygen-containing gases and were burned. The products of combustion were used to synthesize the carbon nanomaterials (CNMs) at the presence of a catalyst. CNMs have a wide range of potential applications due to their extraordinary mechanical, thermal and electrical properties. Produced materials were characterized by SEM and TEM, whereas combustion products were assessed using GC. Results showed that CNMs with outer diameters of 30-100 nm and lengths of about 30 µm were formed. Therefore, it was demonstrated that waste products containing SBR can be used to generate CNMs which are value-added products of intense technological interest.

Resumo em Inglês:

Barium monoferrite BaFe2O4 classified as permanent magnet stands out among other ceramic magnets due to its high chemical stability, corrosion resistance and low production cost. In addition, experiments conducted on photocatalytic degradation of methyl orange and UV transmittance by spectrophotometry have shown that this material has photocatalytic properties. The spinel ferrite is of importance in many technological areas such as computing, communications and security. Several techniques for synthesis have been studied to optimize the properties of this material. The synthesis of BaFe2O4 by conventional processes often occurs at temperatures above 1000 ºC. In this work, we obtained the phase BaFe2O4 at low temperatures (600 ºC) from the combustion reaction using nitrates and maleic anhydride as metal complexing agent. Techniques of X-ray diffraction, specific surface area, thermogravimetry analysis and photocatalytic analysis were employed to characterize the products obtained.

Resumo em Inglês:

Polymer composite pipes are an appealing option as a substitute for conventional steel pipes, particularly due to their inherent corrosion resistance. However, the composite pipes currently used do not allow non-destructive evaluation (NDE) using instrumented devices which operate with magnetic sensors. The present work aims at the development of polymer composites with the addition magnetic markers to allow the application non-destructive evaluation techniques which use magnetic sensors. Glass-polyester composite flat, circular plates were fabricated with the addition of ferrite particles (barium ferrite and strontium ferrite) and four types of notches were introduced on the plates' surfaces. The influence of these notches on the measured magnetic properties of each material was measured. X-ray diffraction (XRD), X-ray fluorescence (XRF) and Brunauer, Emmett, and Teller (BET) nitrogen adsorption were used for the characterization of the ferrite particles. Particle dispersion in the polymer matrix was analyzed by scanning electron microscopy (SEM). According to the results, a particular variation in magnetic field was detected over the region surrounding each type of notch. The results suggest that the proposed technique has great potential for damage detection in polymer composites using magnetic sensors and thus constitute a valuable contribution which may ultimately lead to the development of non-destructive evaluation techniques for assessing the structural integrity polymer composite pipes.

Resumo em Inglês:

Ceramic cutting tools are showing a growing market perspective in terms of application on machining operations due to their high hardness, wear resistance, and machining without a cutting fluid, therefore are good candidates for cast iron and Nickel superalloys machining. The objective of the present paper was the development of Si3N4 based ceramic cutting insert, characterization of its physical and mechanical properties, and subsequent coating with AlCrN using a PVD method. The characterization of the coating was made using an optical profiler, XRD, AFM and microhardness tester. The results showed that the tool presented a fracture toughness of 6.43 MPa.m½ and hardness of 16 GPa. The hardness reached 31 GPa after coating. The machining tests showed a decrease on workpiece roughness when machining with coated insert, in comparison with the uncoated cutting tool. Probably this fact is related to hardness, roughness and topography of AlCrN.

Resumo em Inglês:

Stearic acid (CH3(CH2)16COOH) was treated with Ar and Ar-O2 (10%) pulsed DC discharges created by a cathode-anode confined system to elucidate the role of oxygen in plasma cleaning. The treatment time (5 to 120 minutes) and plasma gas mixture (Ar and Ar-O2) were varied, and the results showed that the mass variation of stearic acid after Ar-O2 plasma exposure was greater than that of pure Ar plasma treatment. Thus, compared to Ar*, active oxygen species (O and O2, in all states) enhance the etching process, regardless of their concentration. During the treatments, a liquid phase developed at the melting temperature of stearic acid, and differential thermal analyses showed that the formation of a liquid phase was associated with the breakage of bonds due to treatment with an Ar or Ar-O2 plasma. After treatment with Ar and Ar-O2 plasmas, the sample surface was significantly modified, especially when Ar-O2 was utilized. The role of oxygen in the treatment process is to break carbonaceous chains by forming oxidized products and/or to act as a barrier again ramification, which accelerates the etching of stearic acid.

Resumo em Inglês:

In dual purpose water/power co-generation plants, the presence of high concentration of Cu and Ni in the re-circulating brine/condensate as a result of condenser tubes corrosion has been attributed as one of the several causes of corrosion damage of flash chamber materials and water touched parts of the boilers. The present investigation deals with the effect of dissolved nickel in the concentration range of 10 ppb to 100 ppm on the corrosion behavior of mild steel and SS 304L in two aqueous medium namely, distilled water and artificial seawater. The effect of pH, dissolved oxygen and flow condition of aqueous medium on the corrosion behavior was also monitored. The experimental techniques include immersion test and electrochemical tests which include free corrosion potential measurements and potentiodynamic polarization measurements. The corrosion rate of mild steel and SS 304L under different experimental conditions was determined by weight loss method and spectrophotometric determination of iron ion entered into the test solution during the period of immersion. The pH of the test solution was also monitored during the entire period of immersion. The left over nickel ions present in the test solution after completion of immersion was also estimated using Atomic Absorption Spectrophotometer. The surface morphology of the corroded steel surface was also examined using scanning electron microscopy (SEM). The results of the studies show that SS 304L largely remains unaffected in both distilled water and artificial seawater under different experimental conditions. However, the effect of nickel on the corrosion behavior of mild steel is quite pronounced and follows interesting trends.

Resumo em Inglês:

The microstructural evolution and corresponding phase transformations have been investigated during partial remelting of AZ91D magnesium alloy refined by Al-Ti-B master alloy. The effect of heating temperature on semisolid microstructure has also been discussed. The results indicate that the microstructural evolution process includes four stages, the initial rapid coarsening, structure separation, spheroidization accompanied by coarsening and the final coarsening. Two or more equiaxed dendrites in the as-cast microstructure evolve into one spheroidal primary particle in the semisolid microstructure through the former three stages. The initial rapid coarsening results from the reaction of β→α, the structure separation is due to the α + β→L and α→L, the spheroidization is attributed to the α→L and the final coarsening is ascribed to the two reverse reactions of α→L and L→α. Rising the heating temperature during partial remelting is beneficial for obtaining small and spheroidal primary particles.

Resumo em Inglês:

The influence of curing tip distance and storage time on the hardness of a composite was evaluated. Composite samples (Filtek Z250) were polymerized at different distances (5, 10, and 15 mm), compared with a control group (0 mm), and stored in distilled water at 37 ° C for 24 hours. The Knoop-hardness of top and bottom surfaces was assessed (25 g/30 s). Specimens were stored in distilled water for 6 and 12 months and were retested. Hardness was found to be negatively influenced by both curing tip distance and storage time. Despite similar values at 24 hours, differences in hardness values compared with the control group appeared over time. In comparing both surfaces, hardness proved to be greater at the top surface for all groups. Composites with similar initial hardness values can degrade very differently after water storage. The higher the photoactivation distance and storage time, the worse the mechanical property.

Resumo em Inglês:

The membranes properties prepared from water/formic acid (FA)/ polyamide 66 (PA66) and water/hydrochloric acid (HCl)/polyamide 66 (PA 66) systems has been studied. The different solvents interact distinctly with the polymer, affecting the membrane morphology. The asymmetric structure of the membranes showed a dense top layer and a porous sublayer. The membranes M-HCl prepared from HCl/PA 66 system showed a larger dense layer (around 23 μm) in compared to those prepared from FA/PA 66 system (M-FA) (around 10 μm). The membrane morphology was a determinant factor in results of water absorption, porosity and pure water flux. The lower thickness of dense layer in M-FA membranes resulted in a higher water absorption and, consequently, porosity, approximately 50%, compared with M-HCl membranes, approximately 15%. The same trend was observed to permeate flux, the lower thickness of dense layer higher pure water flux.

Resumo em Inglês:

Silica nanoparticles particles were synthesized from rice hulls and characterized. The particles were found to be amorphous in nature, ranging in size from 50 to 100 nm. The concentration of silica nanoparticles, pH and curing time were taken as independent variables to design the experiment. Box-Behnken method has been used to derive the experimental plan and fifteen experiments were conducted. Regression equations have been formed with the dependent and independent variables and the results of all possible combinations have been derived. The combination of optimized concentration of BTCA and SHP were used as crosslinking agent and catalyst respectively and silica nano particles were used to enhance the physical properties of the cotton fabric. The effect of pH and curing time on physical properties were analysed by FTIR studies. By ranking method the best combination of process parameters were identified. From this study, it was observed that higher concentration of silica nanoparticles with BTCA improve the crease recovery angle and tensile strength. FTIR studies revealed that the increase of pH and curing time increases the ester carbonyl band intensity ratio.

Resumo em Inglês:

Nano-carbon materials, such as carbon nanotubes and carbon nanofibers, are being thought to be used as multifunctional reinforcement in composites. The growing of carbon nanofiber at the carbon fiber/epoxy interface results in composites having better electrical properties than conventional carbon fiber/epoxy composites. In this work, carbon nanofibers were grown in situ over the surface of a carbon fiber fabric by chemical vapor deposition. Specimens of carbon fiber/nanofiber/epoxy (CF/CNF/epoxy) composites were molded and electrical conductivity was measured. Also, the CF/CNF/epoxy composites were tested under flexure and interlaminar shear. The results showed an overall reduction in mechanical properties as a function of added nanofiber, although electrical conductivity increased up to 74% with the addition of nanofibers. Thus CF/CNF/epoxy composites can be used as electrical dissipation discharge materials.

Resumo em Inglês:

In this work, 17-4PH stainless steel parts processed in a Plasma Assisted Debinding and Sintering (PADS) furnace were characterised in terms of microstructure, final density, microhardness, carbon content and tensile behaviour. To determine whether these properties were satisfactory, the same characterisation procedure was conducted on the parts processed by conventional batch furnaces that are normally employed in Metal Injection Moulding industrial plants. The properties were in good agreement, and only slight differences like an extremely low carbon content (0.003% w/o) were observed. It has been seen that not only economical advances but also intricate materials with suitable responses may be obtained using PADS.

Resumo em Inglês:

The thermo-mechanical degradation during the multi-extrusion of unstabilized and stabilized polypropylene copolymer (cPP) was analyzed using the Chain Scission Distribution Function (CSDF) method. During the first extrusion of unstabilized cPP almost 60% of the initial polymeric chains were submitted to chain scission. The calculations using CSDF show a random chain scission process of chains with molecular weight below 100 kg.mol-1, and above that a preferential chain scission process. When stabilized the cPP molecular weight is kept constant, even after four extrusions, independently of the stabilizers concentration used. Its chain scission is greatly reduced, only being noteworthy at high values of molecular weight, presenting in this case a preferential chain scission process. During extrusion the unstabilized cPP evolves Volatile Organic Compounds (VOC) due to the volatilization of low molecular weight oxidized chain segments. VOC's emissions are greatly reduced during the melt processing of stabilized cPP, even after multiple extrusions.