Resumo em Inglês:

In this work, pure and Alumina doped cobalt ferrite nanoparticles CoFe2−xAlxO4 (for x = 0.44) have been synthesized by the sol gel method. The influence of alumina doping on the morphological and mechanical properties of CoFe2O4 nano-particles were investigated by means of X-ray powder diffraction (XRD) and rietveld analysis. XRD analysis confirmed that the single phase formation of pure nano particles with the expected cubic inverse spinel structure with Fd3m space group and without any impurity phase. Alumina doping were led to a decrease in the crystallite size, lattice parameter, elastic constants and magnitude of moduli. It is explained on the basis of the replacement of Fe ions with half-filled d-shell (3d5) and larger radius by Al3+ ions with a completely filled shell (2p6) and smaller radius.

Resumo em Inglês:

The objective of this work is to investigate the influence of the crystallographic texture on the corrosion resistance of 16% Cr ferritic stainless steel. Samples of ASTM S43000 ferritic stainless steel, both niobium-stabilised and non-stabilised, were used. The samples were subjected to crystallographic characterisation (EBSD) and analysed using an inverse pole figure (IPF) and a crystalline orientation distribution function (CODF). The samples also underwent anodic potentiodynamic polarisation tests (deaeration by high-purity argon gas) in 3.56% NaCl and 1N H2SO4 solutions, and the surface was examined by SEM after the tests. The results showed a clear influence of the crystallographic texture on the corrosion resistance. The niobium decreases the amount of the preferred orientation and thus the influence of the texture on the corrosion resistance, although the corrosion resistance of the stainless steel is increased as niobium carbides are formed.

Resumo em Inglês:

The influence of different supporting electrolytes as well as of different current densities on RO16 dye electrochemical oxidation using BDD electrodes has been systematically studied. The RO16 azo-dye electrooxidation experiments were performed at different current densities and three different supporting electrolytes: H2SO4 0.1 mol L-1, HClO4 0.1 mol L-1 and K2SO4 0.1 mol L-1. The results showed that a higher degradation for reactive azo dye RO16 was observed for the K2SO4 (pH=10) supporting electrolyte for a current density of 100 mA cm-2. This behavior can be associated with the deprotonation effect of the dye molecule, which can facilitate breakdown of the molecule, specifically the azo bond making color removal more efficient. In addition, in this pH there is a greater amount of hydroxyl ion (OH-) available increasing the hydroxyl radical formation.

Resumo em Inglês:

Li doped bismuth oxide nanorods have been prepared using sodium bismuthate and Li acetate. X-ray diffraction (XRD) pattern shows that the nanorods are composed of monoclinic Bi2O4 and cubic LiBi12O18.50 phases. Scanning electron microscopy (SEM) observation shows that the nanorods have the length and diameter of 1-5 µm and 50-350 nm, respectively. The formation of the Li doped bismuth oxide nanorods is closely relative to the hydrothermal conditions. The electrochemical performance for the determination of L-cysteine based on a Li doped bismuth oxide nanorods modified glassy carbon electrode (GCE) has been developed. The CV peak current increases obviously and linearly with increasing the scan rate. Under the optimal conditions, Li doped bismuth oxide nanorods modified GCE exhibits good analytical performance with good reproducibility and stability. The linear range of L-cysteine is 0.0001-2 mM and the detection limit is 0.36 µM and 0.17 µM for cvp1 and cvp2, respectively.

Resumo em Inglês:

The substitution effects of Fe ion on the structure of the intermetallic Bi3Ni1-xFex (0 ≤ x ≤ 0.10) superconductor were studied. The morphology of samples consists of an inhomogeneous laminar slab-like microstructure. The main phase corresponds to Bi3Ni1-xFex with an orthorhombic structure (Pnma), but with very small quantities of impurities of BiNi and Bi as revealed by X-ray diffraction. SEM and AFM reveal that the Bi3Ni1-xFex phase consists of two regions. One region is Bi richer and Ni and Fe poorer than the other region. Raman spectroscopy revealed two phonon modes at room temperature. No significant changes were observed in the spectra with Fe doping and in different regions of the Bi3Ni1-xFex phase. Superconductivity is observed below a transition temperature TC = 4 K and regardless of iron doping.

Resumo em Inglês:

ZnO thin films with wurtzite structure have been grown on Si (100) and glass substrates using radio frequency (rf) magnetron sputtering at room temperature. The ZnO thin films have been characterised by XRD. The (002) orientation is observed at zero Oxygen flow after the (100) developed with increasing oxygen ratio. Usually, this orientation (100) is difficult to obtain. The thickness of ZnO films was confirmed by cross-section SEM, and their stoichiometry was measured by Energy Dispersive X-ray Spectroscopy (EDX) and Rutherford backscattering spectroscopy (RBS). The optical band gaps have been determined using UV spectra and found to be varied from 3.24 to 3.29 eV as a function of the oxygen ratio. Moreover, photoluminescence (PL) spectra showed more defects at higher oxygen flow. The crystalline quality of the deposited film degrades with oxygen enhancements.

Resumo em Inglês:

Manganese selenite (MnSeO4) crystalline thin film has been produced with chemical bath deposition on substrates (commercial glass). Properties of the thin film, such as transmittance, absorption, and optical band gap and refraction index have been investigated via UV/VIS Spectrum. The structural properties of orthorhombic form have been observed in XRD. The structural and optical properties of MnSeO4 thin films, deposited at different pH levels were analyzed. Some properties of the films have been changed with the change of pH level, which has been deeply investigated. The grain size of MnSeO4 thin film has reached its highest value at pH 9. The refraction index and extinction coefficient of MnSeO4 thin films were measured to be 1.53, 2.86, 2.07, 1.53 (refraction index) and 0.005, 0.029, 0.014, 0.005 (extinction coefficient) for grain sizes 21, 13, 26, and 5 nm respectively. The band gaps (Eg) of the films were measured to be 2.06, 2.57, 2.04, and 2.76 eV for the grain sizes mentioned above. The value of dielectric constant at pH 10 was calculated as 1.575.

Resumo em Inglês:

The visible light driven BiPO4 nanocubes with sufficient surface oxygen deficiency were fabricated by a hydrothermal process and subsequently ultrasonic assistant Fe reduction process. The products were characterized by XRD, DRS, XPS, SEM and TEM which showed that the BiPO4 had cuboid-like shape with a smooth surface and clear edges and the oxygen vacancies were succesfully introduced on the surface of the BiPO4 nanocubes. The as prepared oxygen-deficient BiPO4 nanocubes showed greatly enhanced visible light induced photocatalytic activity in degradation of Rhodamine B. The enhanced photocatalytic performance and expanded visible light response of BiPO4 may be due to the introduction of surface oxygen vacancies which can generate the oxygen vacancies mid-gap states lower to the conduction band of BiPO4.

Resumo em Inglês:

This work concerns the preparation a nitrogen-doped TiO2 by ionothermal synthesis methods and the photocatalytic studies. In this procedure, alkoxide was used as a titanium source, and a deep eutectic mixture of choline chloride and urea (molar ratio 1:2) served as a solvent and source of nitrogen. Different samples were synthesized varying the percentages of the eutectic mixture, titanium butoxide, and water, as well as temperature and reaction time. The catalysts were characterized by X-ray diffraction, Raman spectrometry, scanning electron microscopy, and diffuse reflectance spectroscopy. N-doping was confirmed by X-ray photoelectron spectroscopy. The photocatalytic activity of the N-TiO2 nanoparticles was evaluated in the oxidation of N,N-dimethyl-4-nitrosoaniline (RNO) dye. The best photocatalytic activity under illumination by UV and visible light was found for the catalysts prepared under reflux in the presence of water, and for the catalysts prepared hydrothermally using intermediate percentages of the nitrogen source (the eutectic mixture).

Resumo em Inglês:

The phase field model based on the nonlinear Cahn-Hilliard equation was applied to analyze the spinodal decomposition process in Al-Zn and Al-Zn-Cu alloys. Partial differential equations were solved using the explicit finite difference method for the Al- 20, and 35 at. % Zn alloys aged at temperatures between 25 and 100 °C for times from 10 s to 2000 s and Al-20at.%Zn-10at.%Cu and Al-20at.%Zn-5at.%Cu alloys at temperatures between 400 and 500 °C for times from 3600 to 360000 s. Thermo-Calc indicated that the copper addition extends the presence of the metastable miscibility gap up to a temperature of about 597 °C in comparison to the temperature of 350 °C for the binary case. This miscibility gap was calculated assuming that the equilibrium phases were not present and thus it is only existing at the early stages of aging. Simulation results pointed out that the phase decomposition process is much faster in the binary alloys than that in the ternary alloys in spite of the higher aging temperature for the latter case.

Resumo em Inglês:

SALF program is a Brazilian program developed to simulate the cold flat rolling process by the finite element method. The program uses the implicit and rigid-plastic approaches to perform numerical analyses. This article presents the cold flat rolling simulations performed by SALF, where the variables of rolling force, effective strain rate, and effective strain were analyzed. The simulations were chosen from the literature and involved materials such as steel and aluminum, with thicknesses of 1.0 mm and 3.0 mm, reductions of 5%, 16.67%, and 30%, and friction coefficients of 0.08, 0.1, and 0.3. The results showed that SALF describes the above variables appropriately in qualitative and quantitative terms. However, based on the research results, domestic steel industries may now use a national program to simulate the cold flat rolling process to improve their processes and products.

Resumo em Inglês:

The ophthalmic dysfunction amblyopia, commonly known as lazy eye, is characterized by decreased vision in one eye due to improper development in childhood. The aim of this study was to obtain and characterize natural rubber membranes and to assess their utility as an eye film capable of altering the passage of light. The latex membranes were produced using the Van Gogh method and the deposition technique and were analyzed by physical and chemical methods to determine the properties of latex in natura and of natural rubber membranes. The materials were characterized by X-ray diffractometry, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, analysis of water sorption and light crossing analysis. We report here a new approach to the treatment of patients with amblyopia using latex membranes.

Resumo em Inglês:

The present article depicts the specific wear rate of jute fiber reinforced epoxy composites with different weight percentage of fiber loading (10, 20, 30, 40 wt. %) and different chemical treatments (Alkaline and Benzoyl chloride treatment). The three-body abrasive wear analysis was studied according to ASTM-G65 using a rubber wheel abrasion apparatus (dry sand wear tester) at room temperature by varying different factors like fiber content, abrasive particle size, normal load and sliding distance. To calculate the abrasive wear behaviour of jute/epoxy composites, the design of experiments approach based on Taguchi’s orthogonal array has been adopted. Steady state result shows that with the inclusion of chemical treatment in jute fiber improved wear resistance capacity of the composites. Finally, scanning electron microscope (SEM) studies revealed the morphologies worn surface of the composites such as micro-ploughing, formation of debris, micro cracking and fiber matrix de-bonding.

Resumo em Inglês:

Among the applications for protic ionic liquids (PILs), lubrication is one of the newest and the most promising. In this work, ammonium-based protic ionic liquids were tested as lubricant fluids for aluminum-steel contacts. PILs were synthesized with 2-hydroxyethylamine (2HEA) and a carboxylic acid (formic and pentanoic), aiming to understand the effect of two different anion chain lengths on the lubricant behavior. The synthesized PILs were characterized by RMN, FTIR and TGA. Wear tests, conducted using a ball-on-plate configuration, showed that the increase of the anion carbon chain length in the PIL structure reduced significantly the coefficient of friction value. Besides, after the wear tests, the PILs structural integrity was not affected. In the same way, bending under tension (BUT) tests evidenced that the performance for stamping conditions of the PIL with the longest anion carbon chain was similar to that of the commercial lubricant. Since, both formed a uniform tribofilm, developed the same lubrication regime and the drawing forces values were close and constant. Hence, the ionic liquid obtained with 2HEA and pentanoic acid (2HEAPe) is as suitable as the commercial lubricant for metal forming processes.

Resumo em Inglês:

The application of cellular automata in materials science requires the conversion of the automata's rules and abstract general properties to rules and properties associated with the material and phenomena under study. In this paper we propose a model which uses cellular automata to simulate recrystallization and grain growth during isothermal and non-isothermal treatments of cold worked polycrystalline materials. The algorithm's spatial and temporal scaling is based on known experimental results for recrystallization and grain growth in highly cold-worked commercially pure titanium grade 2. In the recrystallization, the best agreement between experimental and computational results in terms of the process kinetics and the average diameter of recrystallized grains is obtained from a nucleation model that considers the temperature-dependent nuclei formation rate. In the simulation of grain growth after primary recrystallization, the results indicate the normal growth of an equiaxed grain structure whose kinetics and dimensions are comparable to those observed experimentally.

Resumo em Inglês:

Silver orthophosphate (Ag3PO4) had been reported as an excellent candidate to split water or decompose pollutants with high efficiency in visible light region, yet is not stable due to the reduction of silver ion. In this work, an easy-fabricated method (in situ photoinduced reduction) was provided to enhance the stability of Ag3PO4 for its possible application as a visible-light sensitive photocatalyst. The as-prepared samples were characterized by X-ray diffraction (XRD), UV-vis diffuse reflectance spectra, photoluminescence spectra (PL) and Photoelectrochemical measurements. The Ag3PO4/Ag photocatalysts showed strong photocatalytic activity for decomposition of RhB dye or phenol-X-3B mixture under visible light irradiation (λ> 420 nm) and can be used repeatedly. The possible mechanism for the enhanced photocatalytic properties of the Ag3PO4/Ag hybrid was also discussed. It was found that •OH and holes take priority over •O2- radicals in serving as the main oxidant in the Ag3PO4/Ag photocatalytic system. Especially, the experimental results indicate that the surface plasmon resonance of Ag nanoparticles and a large negative charge of PO43- ions as well as high separation efficiency of e--h+ pairs, facilitated the enhancement of the photocatalytic activity of the Ag3PO4/Ag composite. The results indicated that Ag3PO4/Ag is an efficient and stable visible-light-driven photocatalyst.

Resumo em Inglês:

In the present work, we have investigated the structural and electrical properties of CrN thin films for a thickness t in the 30-220 nm range, grown on Si (100) substrates. The CrN/Si (100) films exhibits a structural transition from hexagonal phase (β-Cr2N) to cubic phase (CrN) with the increasing in film thickness, the change in structural transition is attributed to the decrease of film-substrate interfacial strain. From electrical resistivity measurements, the thickness of 150 nm CrN/Si (100) film shown the metal-semiconductor phase transition at around 250 K with energy band gap (Eg) 81 meV in semiconducting region, whereas the thickness of 30, 110 and 220 nm CrN/Si(100) films were shown only semiconducting behaviour for whole temperature range of 50-400 K. On the other hand, a clear grain size was increased in CrN/Si films with increasing thickness and its influence on transport properties was also seen. The possibility of phase transition and occurrence of semiconducting behaviour in the CrN films were analysed.

Resumo em Inglês:

An experimental centrifugal atomiser was used to study the manufacture of zinc powder. Melt temperature, melt flow rate, rotating speed and diameter of the atomising disc, are operating parameters that were varied, and their effects on powder quality and yield were observed. The median particle size and the particle size distribution tended to be better, i.e. smaller and narrower, with increasing rotating speed, melting temperature, and atomising disc size. With decreasing melt flow rate, the median particle size decrease and the particle size distribution is similar, all curves are almost overlapping. The yield of zinc powder increased with rotating speed and disc size, and decreased with melt flow rate. Apparent densities of zinc powder were in the range from 1.65 to 2.51 g/cm3. In SEM micrographs most zinc particles were irregular in shape, and the particle structure was mainly cellular based on optical imaging after etching of a polished surface.

Resumo em Inglês:

This work evaluates the corrosion process caused by the presence of hydrogen sulfide in the biogas in natura, in steels commonly used in the construction of steam generator boilers, simulating conditions close to those found on the real application of these materials, exposing the test bodies directly to biogas in natura, flame of combustion and gases resulting from the combustion of this biofuel, in chimney. After 314 hours of exposure under the specified conditions, the corroded surfaces of ASTM A178 and ASTM A516 were analyzed, by optical microscopy, electronic scanning microscopy, X-ray diffraction and surface hardness. The determination of corrosion rates for each test condition and each material tested can be used as a parameter for the determination of the minimum tolerance for mechanical stability, in the calculation of the minimum required thickness of the structural elements of the steam generator boilers fed to biogas.

Resumo em Inglês:

Magnetic nanoparticles can improve the efficiency of phase separation time in multi-stage operations when a magnetic field is present. As such operations involve contact with aqueous and/or organic solutions, hydrophilic magnetic nanoparticles synthesized through the co-precipitation method were functionalized with oleic acid to attain hydrophobic magnetic nanoparticles. Both nanoparticles were characterized morphologically, chemically and magnetically. The results revealed that the particles (size ≈ 10 nm) consisted of an iron oxide mixture of magnetite and maghemite. The functionalization with oleic acid was effective in converting them into hydrophobic nanoparticles. Both particles were ferro/ferrimagnetic and the presence of oleic acid did not interfere significantly in the saturation magnetization value. The chemical stability of both nanoparticles were also evaluated, as an attempt of simulating broad industrial conditions to which the nanoparticles may be subjected; the hydrophilic nanoparticles were resistant at pH ≥ 4, while the hydrophobic nanoparticles were stable at pH ≥ 3.

Resumo em Inglês:

The aluminum bronze alloy is part of a class of highly reliable materials due to high mechanical strength and corrosion resistence being used in the aerospace and shipbuilding industry. It's machined to produce parts and after its use cycle, it's discarded, but third process is considered expensive and besides not being correct for environment reasons. Thus, reusing this material through the powder metallurgy (PM) route is considered advantageous. The aluminum bronze chips were submitted to high energy ball milling process with 3% of niobium carbide (NbC) addition. The NbC is a metal-ceramic composite with a ductile-brittle behaviour. It was analyzed the morphology of powders by scanning electron microscopy as well as particle size it was determined. X ray diffraction identified the phases and the influence of milling time in the diffractogram patterns. Results indicates that milling time and NbC addition improves the milling efficiency significantly and being possible to obtain nanoparticles.

Resumo em Inglês:

In recent decades, changes in the surface properties of materials have been used to improve their tribology characteristics. However, this improvement depends on the process, treatment time and, essentially, the thickness of this surface film layer. Physical vapor deposition (PVD) has been used to increase the surface hardness of metallic materials. The aim of the present study was to propose a numerical-experimental method to assess the thickness (l) of films deposited by PVD. To reach this objective, Vickers experimental hardness data (HV) assays were combined with numerical simulation to study the behavior of this property as a function of maximum penetration depth of the indenter (hmax) into the film/substrate conjugate. A strategy was developed to combine the numerical results of the H x hmax/l curve with Vickers experimental hardness data (HV). This methodology was applied to a TiN-coated M2 tool steel conjugate. The mechanical properties of the studied materials were also determined. The thickness results calculated for this conjugate were compatible with their experimental data.

Resumo em Inglês:

The NaOH/metakaolin ratio and crystallization time were studied for the synthesis of zeolite NaA from a sample of kaolin from a Capim mine. The tests were carried out by using statistical design with axial points and replication of the central point. The samples obtained were characterized by X-ray diffraction (DRX), scanning electron microscopy and chemical analysis using a microprobe EPMA. The results showed that there is a relationship between the amount of NaOH added and crystallization time. The tests carried out using the lowest NaOH/metakaolin ratio (0.5) and the shortest time (4 h) produced a non-crystalline material. On the other hand, increasing the NaOH/metakaolin ratio and the crystallization time led to the formation of a NaA phase with a high structural level, but with the presence of a sodalite phase as an impurity.

Resumo em Inglês:

Studies regarding biodegradable nanocomposites to be used as orthopedics devices have been intensified. This work aims to investigate the influence of ND dispersion on thermal and mechanical properties of a biocomposite of poly(3-hydroxybutyrate) (P(3HB)) reinforced with nanodiamonds (ND) intended to be used as orthopedics devices, with advantages as biodegradability. In order to improve its dispersion, P(3HB) has encapsulated ND in three different mass ratios: P(3HB):ND(16:1), (12:1) and (8:1). However, for all formulations, NDs are presented as agglomerates, in different intensities. In order to relate the distribution of ND within the polymer matrix and biocomposite properties, TGA, DSC, and DMA analysis were done. The formulation with higher content of ND, P(3HB):ND(8:1), presents larger aggregates; thus, decreasing its properties. With smaller and more distributed agglomerates, the 12:1 ratio composite displayed superior storage modulus and glass transition temperature, probably due to better polymer chain restriction.

Resumo em Inglês:

The effect of a travel speed of 200 mm/min as well as a tool rotational speed of 1200 rpm on butt joint quality of friction stir welding (FSW) ZK60 magnesium casting alloy containing 1.5 wt.% rare earths (ZK60-1.5RE) was investigated to determine microstructure and residual stresses. FSW results in the generation of heterogeneous metallurgical structures consisting of the base material (BM), stirred zone (SZ) and thermo-mechanical affected zone (TMAZ). The stirring action also produced a non-uniform distribution and segregation of intermetalics. The transversal distribution of the longitudinal welding stresses exhibits a "M-like" shape with mostly tensile stresses under the shoulder region and only one compressive stress peak in the advancing side of the SZ and TMAZ. It could be demonstrated that FSW of ZK60-1.5RE alloy was successful in the welding conditions applied during the present work.

Resumo em Inglês:

Spark plasma sintering has been used to successfully produce WC-6Co-xCr3C2, WC-6Co-xTaC (x = 0.2, 0.6, 1.0) and WC-6Co-xCr3C2-xTaC (x = 0.1, 0.3, 0.5) cemented carbides. The spark plasma sintered compacts were investigated by scanning electron microscopy, hardness tests and fracture toughness tests. The results were compared to an additives-free WC-6Co cemented carbide consolidated under the same process parameters and commercial ISO K10 inserts. By using Cr3C2 and TaC additives, it is possible to improve the hardness and fracture toughness of WC-Co cemented carbides. The best combination of hardness (1936 ± 15 HV30) and fracture toughness (10.38 ± 0.46 MPa∙m1/2) was obtained by the WC-6Co-1Cr3C2.

Resumo em Inglês:

Bi2MoO6 nanosheets were synthesized by a hydrothermal method. Morphology and structure of the Bi2MoO6 nanosheets were analyzed by SEM, XRD, N2 adsorption techniques and XPS. Gas-sensing properties of the as-prepared Bi2MoO6 sensors were also systematically investigated. The results showed the reaction temperature greatly affected the morphology and structure of as-prepared Bi2MoO6 nanosheets. When the reaction temperature reached 170 ºC, the morphology of the Bi2MoO6 nanosheets tended to regular, and pure Bi2MoO6 nanosheets were obtained. The operating temperature determined the gas-sensing properties of the Bi2MoO6 sensor. At this optimal operating temperature of 300 ºC, the sensitivity of the Bi2MoO6 sensor towards 20 ppm nitrogen oxide (NO) reached a maximum of 3.13. With the increase of the nitrogen oxide (NO) concentration, the sensitivity of the Bi2MoO6 sensor also rapidly increased, and displayed an almost linear relationship between them. Additionally, the Bi2MoO6 sensor demonstrated excellent selectivity with respect to several typical interfering gases.

Resumo em Inglês:

This study evaluated the effect of adding poly (ethylene methyl acrylate) (EMA) and cotton linter (CL) on the properties of recycled poly (ethylene terephthalate) (PETrec). For this, PETrec/EMA blend and PETrec/EMA/CL composite were developed. In order to improve the interfacial adhesion and the properties of these materials, ethylene/methyl acrylate/glycidyl methacrylate terpolymer (EMA-GMA) and polyethylene-grafted maleic anhydride (PE-g-MAH) were added. The rheological results showed that the addition of EMA increased and the addition of 1 wt% of CL reduced the viscosity. The morphological analysis of the non-compatibilized blend and composite showed poor interfacial adhesion. Polymer blends with 2 and 6 wt% of EMA had better mechanical properties, since these formulations have the smallest average particle diameter of 0.58 and 1.00 µm, respectively. The mechanical testing of composites showed a material with higher maximum strength and elasticity modulus than polymer blend when analyzed at the same EMA phase concentration. The use of EMA-GMA was effective in reducing the size of particles of the EMA in the blend.

Resumo em Inglês:

In this study, influences of growth velocity and composition (Fe content) on the microstructure (rod spacing) and mechanical properties (microhardness, ultimate tensile strength and fracture surface) of Al-Mn-Fe ternary alloys have been investigated. Al-1.9 Mn-xFe (x=0.5, 1.5 and 5 wt. %) were prepared using metals of 99.99% high purity in the vacuum atmosphere. At a constant temperature gradient (6.7 K/mm), these alloys were directionally solidified upwards under various growth velocities (8.3-978 µm/s) using a Bridgman-type directional solidification furnace. The results show that two kinds of Al-rich α-Al phase and Fe-rich intermetallic (Al6FeMn) phase may be present in the final microstructures of the alloys when the Fe content increases from 0.5 wt.% to 5 wt.%. Al6FeMn intermetallic rod spacing, microhardness and ultimate tensile strength were measured and expressed as functions of growth velocity and Fe content by using a linear regression analysis method. According to experimental results, the microhardness and ultimate tensile strength of the solidified samples increase with increase in the growth velocity and Fe content and decrease in rod spacing. The elongations of the alloys decrease gradually with increasing growth velocity and Fe content.

Resumo em Inglês:

The main refractory lining of blast furnace hearth is composed by carbon blocks that operates in continuous contact with hot gases, liquid slag and hot metal, in temperatures above 1550 ºC for 24 hours a day. To fully understand the wear mechanism that acts in this refractory layer system it was performed a Post Mortem study during the last partial repair of this furnace. The samples were collected from different parts of the hearth lining and characterized using the following techniques: Bulk Density and Apparent Porosity, X-Ray Fluorescence, X-ray Diffraction, Scanning Electron Microscopy with Energy-dispersive X-Ray Spectroscopy. The results showed that the carbon blocks located at the opposite side of the blast furnace tap hole kept its main physicochemical characteristics preserved even after the production of 20x106 ton of hot metal. However, the carbon blocks around the Tap Hole showed infiltration by hot metal and slag and it presents a severe deposition of zinc and sulfur over its carbon flakes. The presence of these elements is undesired because it reduces the physic-chemical stability of this refractory system. This deposition found in the carbon refractory is associated with impurities present in the both coke and the sinter feed used in this blast furnace in the last few years.

Resumo em Inglês:

Biomaterials with the hydroxyapatite and biopolymers such as chitosan derived of crustaceans are is an alternative for bone repair. Carbon nanotubes have been a focus of interest because they can ameliorate the biomechanical properties of biomaterials. The objective of this study was to evaluate these materials in the repair of cranial defects in rats. The animals were divided in groups: without implant (G1), implanted with the chitosan/carbon nanotube membrane (G2), and chitosan/nanotube membrane mineralized with hydroxyapatite (G3). The animals were sacrificed 5 weeks after surgery and the skulls were removed for analysis of the defect area. The results showed absence of chronic inflammatory and little bone neoformation in the defect area of all groups. In G2 and G3 there was lack of reabsorption of the biomaterial that were encapsulated by connective tissue. In conclusion, the biomaterials were biocompatible, but their specific physicochemical properties did not indicate a considerable osteoregenerative capacity.

Resumo em Inglês:

Poly(ethylene terephthalate)/organically modified montmorillonite (PET/o-Mt) nanocomposites were prepared via melt intercalation in a twin-screw extruder using a polyester ionomer (PETi) as compatibilizer. The o-Mt content used was 0, 1, 3 or 5 wt% and the compatibilizer/o-Mt mass ratio was 0/1, 1/1 or 3/1. The main objective was to study the effects of the addition of o-Mt and compatibilizer on the barrier properties of PET/o-Mt nanocomposites. The nanocomposites showed a significant reduction in CO2 permeability of up to 50% when compared to the neat PET, without significant change in the CO2 solubility revealing the importance of the diffusional path imputed by the organoclay on the overall permeation process. Water vapor permeability was reduced for all nanocomposites, achieving up to 30% reduction for the nanocomposite containing a compatibilizer/o-Mt mass ratio of 1/1. Overall, the nanocomposite containing 5 wt% of organoclay and compatibilizer/o-Mt mass ratio of 1/1 showed the best barrier properties.

Resumo em Inglês:

Flat sintered copper and copper-zirconia substrates, with zirconia nanoparticles contents of 1 and 3 vol%, were produced by aqueous tape casting and controlled sintering. Aqueous suspensions were prepared to a solid content of 58 vol% using 3 wt% commercial binder emulsion. The green tapes were treated at 350 ºC in air to remove organics and sintered at temperatures ranging from 800 to 1000 ºC in atmosphere of Ar/5%H2. Copper tapes reached almost full densification at 900 ºC. Composite with 1 vol% zirconia, sintered at 800 ºC, maintained high density and provided a noticeable increase of the mechanical strength, whereas further additions up to 3 vol% reduced the densification and the resulting mechanical performance became poorer.

Resumo em Inglês:

Oil is a major pollutant of water resources, affects aquatic life, causing environmental degradation. Currently there is an increase in studies of membrane applied to separation of oil-water. Among these membranes, there are composite membranes, which show as main characteristic an association of organic and inorganic membrane properties. In a tangential flow process, the ceramic tube (support) is responsible for the mechanical strength of the membrane and the selective barrier property of the membrane is established by the polymer. The aim of this work is the application of α-alumina/polyamide 66 composite membrane in the retention of sunflower oil from oil-water emulsions and the study of resistance of such membranes in ultrafiltration processes. The α-alumina ceramic tubes were impregnated internally with a solution of polyamide 66 (PA66) (5% w/v) and tested with distilled water and sunflower oil solutions at concentrations of 50, 100 and 200 mg·L-1. Membranes impregnated with PA66 showed a sunflower oil retention between 53.5 and 99.5% and superior membrane resistance (MR) to the permeate flux (1.92 x 1013 a 5.52 x 1013) which explains the decrease in the permeate volume.

Resumo em Inglês:

In this paper, two low carbon microalloyed steels, named as steel A and steel B, were fabricated by ultra fast cooling (UFC). In both steels, the microstructures containing quasi polygonal ferrite (QF), acicular ferrite (AF) and granular bainite (GB) can be obtained by UFC process. The amount of AF in steel B is more than that in steel A. The size and distribution of precipitates (Nb/Ti carbonitrides) in steel B are finer and more dispersed than those of in steel A due to relatively low finish cooling temperature. The mechanical properties of both steels are effectively enhanced by UFC process. UFC process produces low-temperature transformation microstructures containing a significant amount of AF. The mechanical properties of steel B were more satisfactory than those of steel A due to the finer average grain size, the greater amount of the volume fractions and smaller size of secondary phases.