Acessibilidade / Reportar erro

Prediction of soil chemical attributes using optical remote sensing

Predição de atributos químicos do solo utilizando sensoriamento remoto ótico

Abstracts

Soil fertility variability management is one of the pioneering and important areas in which Precision Agriculture has been commercially applied. Consequently, the objective of this work was to predict soil chemical attributes through spectral responses. The 1,000 ha study area used for this report was located in Uberlândia, MG, Brazil. Thirty sampling points were established, at which the soil was collected at 3 different depths. The samples were chemically and physically analyzed and the radiometric data obtained in the 400 - 2500 nm range. Multiple regression equations were generated for sum of bases, cation exchange capacity, base saturation, aluminum saturation, pH, P, K, Ca, Mg, Al, and H, all using 60 soil samples. H, Al, m%, and pH were found to have R² values less than 0.50. Equations with an R² > 0.50 for the other attributes were tested for the 30 unknown soil samples, and the estimated values were obtained. These values were then compared with those determined by conventional analysis. The coefficients of correlation were higher than 50% for all attributes except P and V%. Results indicated that determining chemical attributes with models that are specific for the region is feasible.

soil chemistry; reflectance; laboratory sensor


Uma das primeiras e mais importantes áreas nas quais a Agricultura de Precisão está sendo comercialmente aplicada é o manejo da variabilidade da fertilidade do solo. Desta forma, o objetivo deste trabalho foi predizer o teor dos atributos químicos do solo através da sua resposta espectral. A área de estudo de 1000 ha localiza-se em Uberlândia, MG. Estabeleceu-se 30 pontos de amostragem nos quais o solo foi coletado em 3 profundidades. As amostras foram analisadas química e fisicamente e, os dados radiométricos obtidos com um sensor em laboratório na faixa de 400 - 2500 nm. Equações de regressão múltipla foram geradas para soma de bases, CTC, saturação por bases, saturação por alumínio, pH, P, K, Ca, Mg, Al e H usando 60 amostras de solo. H, Al, m% e pH obtiveram R² < 0,50. As equações com R² > 0,50 para os outros atributos foram testadas para as 30 amostras de solo desconhecidas obtendo-se os valores estimados. Posteriormente, estes valores foram comparados com aqueles determinados pela análise convencional. Os coeficientes de correlação foram maiores que 50% para todos os atributos exceto P e V%. Os resultados indicam que é possível determinar atributos químicos com modelos específicos para a região.

química do solo; reflectância; sensor em laboratório


SOILS

Prediction of soil chemical attributes using optical remote sensing

Predição de atributos químicos do solo utilizando sensoriamento remoto ótico

Aline Marques GenúI, ** Author for correspondence. E-mail: agenu@unicentro.br; José Alexandre Melo DemattêII

IDepartamento de Agronomia, Universidade Estadual do Centro-Oeste, Rua Simeão Camargo Varela de Sá, 3, 85040-080, Guarapuava, Paraná, Brazil

IIDepartamento de Ciência do Solo, Escola Superior de Agricultura "Luiz de Queiroz", Universidade de São Paulo, Piracicaba, São Paulo, Brazil

ABSTRACT

Soil fertility variability management is one of the pioneering and important areas in which Precision Agriculture has been commercially applied. Consequently, the objective of this work was to predict soil chemical attributes through spectral responses. The 1,000 ha study area used for this report was located in Uberlândia, MG, Brazil. Thirty sampling points were established, at which the soil was collected at 3 different depths. The samples were chemically and physically analyzed and the radiometric data obtained in the 400 - 2500 nm range. Multiple regression equations were generated for sum of bases, cation exchange capacity, base saturation, aluminum saturation, pH, P, K, Ca, Mg, Al, and H, all using 60 soil samples. H, Al, m%, and pH were found to have R2 values less than 0.50. Equations with an R2 > 0.50 for the other attributes were tested for the 30 unknown soil samples, and the estimated values were obtained. These values were then compared with those determined by conventional analysis. The coefficients of correlation were higher than 50% for all attributes except P and V%. Results indicated that determining chemical attributes with models that are specific for the region is feasible.

Keywords: soil chemistry, reflectance, laboratory sensor.

RESUMO

Uma das primeiras e mais importantes áreas nas quais a Agricultura de Precisão está sendo comercialmente aplicada é o manejo da variabilidade da fertilidade do solo. Desta forma, o objetivo deste trabalho foi predizer o teor dos atributos químicos do solo através da sua resposta espectral. A área de estudo de 1000 ha localiza-se em Uberlândia, MG. Estabeleceu-se 30 pontos de amostragem nos quais o solo foi coletado em 3 profundidades. As amostras foram analisadas química e fisicamente e, os dados radiométricos obtidos com um sensor em laboratório na faixa de 400 - 2500 nm. Equações de regressão múltipla foram geradas para soma de bases, CTC, saturação por bases, saturação por alumínio, pH, P, K, Ca, Mg, Al e H usando 60 amostras de solo. H, Al, m% e pH obtiveram R2 < 0,50. As equações com R2 > 0,50 para os outros atributos foram testadas para as 30 amostras de solo desconhecidas obtendo-se os valores estimados. Posteriormente, estes valores foram comparados com aqueles determinados pela análise convencional. Os coeficientes de correlação foram maiores que 50% para todos os atributos exceto P e V%. Os resultados indicam que é possível determinar atributos químicos com modelos específicos para a região.

Palavras-chave: química do solo, reflectância, sensor em laboratório.

Introduction

Agricultural producers consider the production area to be homogeneous; therefore, the amount of input for production is applied consistently over the entire area (CORÁ et al., 2004). However, the area typically has considerable differences in its characteristics, especially in regard to soil type, due to pedogenetic processes and factors of soil formation (SOUZA et al., 2008), which leads to variable productivity. For this reason, the identification of management zones that take into account the distribution of soil attributes is important to redefine management practices to minimize costs and maximize yield (BASNYAT et al., 2004).

The application of fertilizers is, without a doubt, one of the greatest costs involved in agricultural production, and therefore, determining the best possible cost-benefit ratio for this type of input is very important. In this respect, remote sensing has been shown to be a valuable source of information in soil fertility variability management, especially after the establishment of precision agriculture.

The traditional method used to determine soil fertility, and consequently recommend fertilizer applications, stems from the results of soil chemical analyses. The basic principle behind this method consists of sampling an area in such a way that analysis of those samples will reflect soil fertility in the area (THOMASSON et al., 2001).

Sample collection for fertility purposes consists of one compound sample comprising 20 subsamples for an area no larger than 20 ha, thus generating a considerable opportunity for error. In the case of precision agriculture, however, sampling consists of 1 to 2.5 points ha-1, resulting in high cost. Demattê et al. (2001) demonstrated that for Oxisols in the State of São Paulo, the recommended sampling rate was 1 to 2 samples ha-1. The authors also found that the analysis of soil samples had the greatest impact on production costs.

Therefore, new soil analysis methods that are less costly and faster have been investigated. The application of spectroscopy as a soil analysis method began after Bowers and Hanks (1965) demonstrated that it was possible to quantify soil attributes, such as moisture and organic matter content, by using reflected energy. In view of this, our work aimed to quantify soil chemical attributes using spectral data obtained in the laboratory and establishing their relationship to chemical management. It is expected that evaluation of the spectral data will show a correlation with the soil's chemical attributes, making quantification of these attributes possible.

Material and methods

Soil sampling and study area characterization

The 1,000 ha study area, located in Uberlândia, Minas Gerais State, Brazil, was defined by the geographical coordinates 19°27' - 19°23' latitude S and 47°57' - 47°51' longitude W. The climate was characterized by a rainy season from October to April and a dry period from May to September.

Thirty points were sampled at three depths, 0 - 20, 40 - 60, and 80 - 100 cm, referred to respectively as A, B, and C. The ninety collected samples were dried, ground and sieved. After that, chemical analyses were performed according to Brazilian guidelines reported in Raij et al. (1987) for pH, OM, Ca, Mg, K, P, Al and H + Al (potential acidity). The SB (sum of bases), CEC (cation exchange capacity), V% (base saturation) and m% (aluminum saturation) values were then calculated.

Obtaining the spectral data

The sample spectral data were obtained in the laboratory with an Infra Red Intelligent Spectroradiometer (IRIS) sensor ranging from 400 to 2,500 nm. The geometry of the system was based on positioning the sensor 27 cm above the sample, which was placed in a Petri dish measuring 9 cm in diameter. The lighting source, a 650 W halogen lamp, produced a non-collimated ray toward the target plane and was positioned 61 cm from the target at a zenithal angle of 20°. The standard reference utilized was a white spectralon plate with reflectance calibrated at 100 %. The spectral ratio between the radiation flow reflected by the reference surface and the sample generated the bidirectional reflectance factor (NICODEMUS et al., 1977).

Statistical analysis

The statistical analysis was performed between the reflectance data obtained in the laboratory for the different chemical attributes of the soils (SB, CEC, V%, m%, pH in CaCl2, P, K, Ca and Mg, Al and H) studied. Twenty-two bands (B) and 13 heights (H) (in nm) were selected for the spectral data: B1: 420-481, B2: 481, B3: 481-596, B4: 596-710, B5: 710-814, B6: 814-975, B7: 975-1350, B8: 1350-1417, B9: 1417, B10: 1417-1449, B11: 1449-1793, B12: 1793-1831, B13: 1865-1927, B14: 1927, B15: 1927-2102, B16: 2101-2139, B17: 2139-2206, B18: 2206, B19: 2206-2258, B20: 2258, B21: 2258-2389, B22: 2389-2498; H1: 469-532, H2: 532-768, H3: 768-876, H4: 876-1353, H5: 1353-1411, H6: 1411-1439, H7: 1439-1783, H8: 1860-1923, H9: 1923-2120, H10: 2120-2206, H11: 2206-2258, H12: 2258-2389, and H13: 2389-2498, as suggested by Nanni and Demattê (2006).

Initially, variables (bands and heights) were selected for each soil attribute through stepwise analysis. Next, a multi-colinearity test was used to eliminate one or more of the variables that acted concurrently by estimating the same attribute that caused an overestimation of that attribute. Then, a statistical model was generated using 60 soil samples and a multiple linear regression analysis. These analyses were performed with the Statistical Analysis System (SAS, 1999). Estimated values were then generated for 30 samples that were meant for testing. These values were obtained only for attributes whose R2 from the multiple regression equation showed values higher than 0.50. Next, a correlation analysis between values determined in the laboratory (DV) and those estimated (EV) by radiometry was conducted.

Results and discussion

The attributes m%, pH in CaCl2, and Al did not have equations with satisfactory results, as their coefficients of determination were around 0.1 (Table 1). These results were lower than those reported by Dunn et al. (2002), Chang et al. (2001), Malley et al. (1999), or Nanni and Demattê (2006). Another attribute that showed an R2 value smaller than 0.5 was hydrogen (0.42). It was interesting to note that the four attributes showing the smallest coefficients of determination were all related (pH and H, m% and Al). Therefore, it could be expected that as the base content increased, an increase in reflectivity also occurred, a result verified by Demattê et al. (2004). On the other hand, little information was available on the action of elements related to soil acidity, such as H, Al, and pH. The lack of precise results for those elements indicated that there was not a logical definition for their increases and decreases as a function of reflected energy.

For SB, V% and CEC, R2 values of 0.83, 0.77, and 0.88 were obtained, respectively (Table 1). Other authors reported values that were similar to those observed (CHANG et al., 2001; GENÚ et al., 2010). However, Demattê and Garcia (1999) found coefficients that were smaller than 0.5 for the same three attributes. The potential CEC (pH 7.0) is an attribute determined by the sum of exchangeable bases, H, and Al. Therefore, the incident energy on the elements that make up CEC reflect the soil's retention capacity. In the area under consideration, CEC was low in most soil samples (approximately 42 mmolc dm-3). In other words, even when the data did not show great variation, the correlation was reasonable, indicating that CEC directly influenced reflected energy.

The exchangeable bases (K, Ca and Mg) and phosphorous showed R2 values between 0.67 and 0.84 (Table 1), which were considered satisfactory and agreed with those obtained by Thomasson et al. (2001). However, Dematê and Garcia (1999) obtained values smaller than 0.4 for these four elements, whereas Malley et al. (1999) reported R2 values higher than 0.9 for the same nutrients. The differences observed between results obtained in this work and other results cited in the literature could be related to the equipment utilized, which have different resolutions, or with selection of the best bands to carry out the tests, as observed by McBratney et al. (2006).

Additionally, the variation in results that were more or less reliable indicated that the deviations were related to the sampling locations and regions. While Demattê and Garcia (1999) correlated chemical elements with reflectance in soil samples from distinct regions in the State of Paraná, an area adding up to 25,620 ha with a total of 45 samples, Thomasson et al. (2001) in turn evaluated areas of approximately 273 ha with 724 samples. Nanni and Demattê (2006) followed the same line by studying an area of 280 ha with a high sampling density. In chemical terms, everything indicated that models should be evaluated for and constructed from smaller areas.

In order to verify if it was possible to utilize these equations to predict soil chemical attributes, those attributes with R2 higher than 0.5 were tested using 30 samples that were not utilized to generate the model. These samples were used to make scatter plots comparing the values determined in the soil analysis laboratory (DV) with the values estimated by the spectral models.

It could be observed that the coefficients obtained in the correlations for the chemical attributes under study were all greater than 0.5 (Figure 1). The sum of bases (SB) and CEC also showed R2 values greater than 0.5 (Figures 1a and 1b), which was in agreement with Nanni and Demattê (2006). Phosphorus (Figure 1d) had the smallest R2 (0.40) when compared with potassium, magnesium, and calcium (Figures 1c, 1e, and 1f, respectively), but V% had the lowest coefficient at 0.35 (Figure 1g).


It was interesting to notice that the sum of bases (SB) and the exchangeable bases studied (K, Ca, Mg) were all related and had high correlation coefficients (Figures 1a, 1c, 1e, and 1f). However, both CEC and V% were also related, both having potential acidity (H + Al) involved in their determination. As observed in Table 1, the equations obtained had low R2, indicating that there was interference with a spectral correlation of these attributes.

With the advent of Precision Agriculture and the need for optimizing and rationalizing soil sample costs, new research projects on remote sensing have been conducted, with a new emphasis placed on soil chemistry. Under this new perspective, Demattê et al. (2004) determined that the application of agro-industrial liquid residues from sugarcane promoted chemical alterations in the soil samples (increasing K and Ca, for example), which in turn were observed from reflectance. In this case, the authors verified a change in reflectance intensity and demonstrated the importance of the elements present in the soil solution on reflected energy.

Based on these questions, papers, such as those by Thomasson et al. (2001) and Dunn et al. (2002), indicated that electromagnetic energy, when studied in detail on a per band basis, was capable of detecting variations in exchangeable elements. This work, according to the results presented in Table 1 and Figure 1, verified the results obtained in these papers and indicated that the electromagnetic spectrum was influenced by these elements. Therefore, these elements are detectable depending on the evaluation methodology.

Conclusion

It was possible to estimate CEC, SB, K, Ca, and Mg content of soils for the region under study from the spectral responses and at levels comparable to those values found from specific models.

Received on August 17, 2009.

Accepted on May 31, 2010.

License information: This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

  • BASNYAT, P.; McCONKEY, B.; MEINERT, B.; GATKZE, C.; NOBLE. G. Agriculture field characterization using aerial photograph and satellite imagery. IEEE Geoscience and Remote Sensing Letters, v. 1. n. 1, p. 7-10, 2004.
  • BOWERS, S. A.; HANKS, R. J. Reflection of radiant energy from soils. Soil Science, v. 100, n. 2, p. 130-138, 1965.
  • CHANG, C. W.; LAIRD, D. A.; MAUSBACH, M. J.; HURBURGH JUNIOR, C. R. Near-infrared reflectance spectroscopy - principal components regression analyses of soil properties. Soil Science Society of America Journal, v. 65, n. 2, p. 480-490, 2001.
  • CORÁ, J. E.; ARAUJO, A. V.; PEREIRA, G. T.; BERALDO, J. M. G. Variabilidade especial de atributos do solo para adoção do sistema de agricultura de precisão na cultura de cana-de-açúcar. Revista Brasileira de Ciência do Solo, v. 28, n. 6, p. 1013-1021, 2004.
  • DEMATTÊ, J. A. M.; GARCIA, G. J. Avaliação de atributos de Latossolo Bruno e de Terra Bruna estruturada da região de Guarapuava, Paraná, por meio de sua energia refletida. Revista Brasileira de Ciência do Solo, v. 23, n. 2, p. 343-355, 1999.
  • DEMATTÊ, J. A. M.; DEMATTÊ, J. L. I.; CAMARGO, W. P.; FIORIO, P. R.; NANNI, M. R. Remote sensing in the recognition and mapping of tropical soils developed on topographic sequences. Mapping Science and Remote Sensing, v. 38, n. 2, p. 79-102, 2001.
  • DEMATTÊ, J. A. M.; GAMA, M. A. P.; COOPER, M.; ARAÚJO, J. C.; NANNI, M. R.; FIORIO, P. R. Effect of fermentation residue on the spectral reflectance properties of soils. Geoderma, v. 120, n. 3-4, p. 187-200, 2004.
  • DUNN, B. W.; BEECHER, H. G.; BATTEN, G. D.; CIAVARELLA, S. The potential of near-infrared reflectance spectroscopy for soil analysis - a case study from the Riverine Plain of south-eastern Australia. Australian Journal of Experimental Agriculture, v. 42, n. 5, p. 607-614, 2002.
  • GENÚ, A. M.; DEMATTÊ, J. A. M.; FIORIO, P. R. Análise espectral de solos da Região de Mogi-Guaçú (SP). Semina: Ciências Agrárias, v. 31, supl. 1, p. 1235-1244, 2010.
  • MALLEY, D. F.; YESMIN, L.; WRAY, D.; EDWARDS, S. Application of near-infrared spectroscopy in analysis of soil mineral nutrients. Communications in Soil Science and Plant Analysis, v. 30, n. 7-8, p. 999-1012, 1999.
  • McBRATNEY, A. B.; MINASNY, B.; VISCARRA ROSSEL, R. Spectral soil analysis and inference systems: a powerful combination for solving the soil data crisis. Geoderma, v. 136, n. 1-2, p. 272-278, 2006.
  • NANNI, M. R.; DEMATTÊ, J. A. M. Spectral reflectance methodology in comparison to traditional soil analysis. Soil Science Society of America Journal, v. 70, n. 2, p. 393-407, 2006.
  • NICODEMUS, F. E.; RICHMOND, J. C.; HSIA, J. J.; GINSBERG, I. W.; LIMPERIS, T. Geometrical considerations and nomenclature for reflectance Washington, D.C.: U.S. Department of Commerce, 1977. (NBS Monograph 160).
  • RAIJ, B. Van; QUAGGIO, J. A.; CANTARELLA, H.; FERREIRA, M. E.; LOPES, A. S.; BATAGLIA, C. O. Análise química do solo para fins de fertilidade Campinas: Fundação Cargill, 1987.
  • SAS-Statistical Analisys System. Statistical analisys system: user's guide version 8.2. Cary: Statistical Analysis System Institute, 1999.
  • SOUZA, G. S.; LIMA, J. S. S.; SILVA, S. A.; OLIVEIRA, R. B. Variabilidade espacial de atributos químicos em um Argissolo sob pastagem. Acta Scientiarum. Agronomy, v. 30, n. 4, p. 589-596, 2008.
  • THOMASSON, J. A.; SUI, R.; COX, M. S.; AL-RAJEHY, A. Soil reflectance sensing for determining soil properties in precision agriculture. Transactions of the ASAE, v. 44, n. 6, p. 1445-1453, 2001.
  • *
    Author for correspondence. E-mail:
  • Publication Dates

    • Publication in this collection
      31 Oct 2011
    • Date of issue
      Dec 2011

    History

    • Received
      17 Aug 2009
    • Accepted
      31 May 2010
    Editora da Universidade Estadual de Maringá - EDUEM Av. Colombo, 5790, bloco 40, 87020-900 - Maringá PR/ Brasil, Tel.: (55 44) 3011-4253, Fax: (55 44) 3011-1392 - Maringá - PR - Brazil
    E-mail: actaagron@uem.br