ERRATUM

Due to a publishing error the article: “The effect of cooling procedures on monomer elution from heat-cured polymethyl methacrylate denture base materials”, published at Journal of Applied Oral Science 2022;30:e20220161 was printed with the following error:

Where it reads:

Figure 1
The heat-cured denture base materials used in the study

* According to the manufacturers’ information. MMA: Methyl methacrylate, PMMA: Polymethyl methacrylate, BPO: Benzoyl peroxide, HQ: Hydroquinone, EGDMA: Ethyleneglycol dimethacrylate, BDMA: Tetramethylene dimethacrylate

It should read:

Figure 1
The heat-cured denture base materials used in the study

* According to the manufacturers’ information. MMA: Methyl methacrylate, PMMA: Polymethyl methacrylate, BPO: Benzoyl peroxide, HQ: Hydroquinone, EGDMA: Ethyleneglycol dimethacrylate, BDMA: Tetramethylene dimethacrylate

Where it reads:

Table 1 The results of the MMA concentration in the water-eluents of the heat-cured PMMA denture base materials tested*

Cooling procedures	MMA eluted in water (ppm)
	PA	PB	QC	VE
A	4.6<LoQ	4.6<LoQ	8.5 (1.7)a,A	6.4 (0.3)b,A
B	<LoD	2.1<LoQ	<LoD	8.7 (2.4)b
C	<LoD	4.8<LoQ	13.2 (2.4)a	2.9<LoQ
D	2.8<LoQ	2.2<LoQ	<LoD	3.2<LoQ
E	<LoD	<LoD	<LoD	4.2<LoQ
Control	<LoD	<LoD	<LoD	<LoD

* Means and standand deviations (in parentheses).Superscript letters show mean values with insignificant differences within each material group (lower case) and between material groups per treatment (upper case). LoQ: Lower limit of quantitation (5.90 ppm), LoD: Limit of detection (1.95 ppm). Bold characters show the values obtained using the cooling modes suggested by the manufacturers. Data given for results <LoQ represent only mean values

It should read:

Table 1 The results of the MMA concentration in the water-eluents of the heat-cured PMMA denture base materials tested*

Cooling procedures	MMA eluted in water (ppm)
	PA	PB	QC	VE
A	4.6<LoQ	4.6<LoQ	8.5 (1.7) a,A	6.4 (0.3)b,A
B	<LoD	2.1<LoQ	<LoD	8.7 (2.4)b
C	<LoD	4.8<LoQ	13.2 (2.4)a	2.9<LoQ
D	2.8<LoQ	2.2<LoQ	<LoD	3.2<LoQ
E	<LoD	<LoD	<LoD	4.2<LoQ
Control	<LoD	<LoD	<LoD	<LoD

* Means and standand deviations (in parentheses).Superscript letters show mean values with insignificant differences within each material group (lower case) and between material groups per treatment (upper case). LoQ: Lower limit of quantitation (5.90 ppm), LoD: Limit of detection (1.95 ppm). Bold characters show the values obtained using the cooling modes suggested by the manufacturers. Data given for results <LoQ represent only mean values

Publication Dates

• Publication in this collection
  22 Aug 2022
• Date of issue
  2022