Granulometric influence on the combustion... GRANULOMETRIC INFLUENCE ON THE COMBUSTION OF CHARCOAL FOR BARBECUE1

The present work analyzed characteristics of charcoal used for barbecue and mainly took interest in the influence of the granulometry in the combustion process. The material have been tested for four different grain size (8, 16, 32 and 50 mm) following a combustion test called combustion index (ICOMcv), which takes in consideration time processing, temperature generated and the mass consumed. The characterization of charcoal was done according to the following parameters, moisture, apparent density, grain density, volatile materials content, ash content, fixed carbon content and calorific value. The proofed charcoal presented standard indicators for use in barbecue and was noticed the relationship between granulometric analysis and the ICOMcv. The 16 mm grain size charcoal sample showed the best results for combustion. By contrast, the largest grain size sample presented lower results compared to the other samples. Thus, establishing unprecedented quantitative indicators in relation to those observed in practice, regarding the influence of grain size on the efficiency of combustion of the charcoal when used for barbecue.


INTRODUCTION
Charcoal is a fuel used since ancient times for various purposes.Currently, it is used as much in the industrial sector, like steel industry, cement and glass, as in the household for barbecue.Warnes (2008), mentioned that cooking was the first essay of food preparation ever done by humankind.
Although the biggest producer of charcoal, most of the feedstock of Brazil is intended for industrial use.However, the country still keeps a strong tradition of using it for barbecue, as Arantes (2009) and Cintra (2009) reported the residential sector consumes 8% of all charcoal produced in the country, followed by the commercial sector 1.1%, represented by pizzerias, bakeries and steakhouses.However, it is worth noting that for some developing countries, such as Haiti, charcoal is one of the main energy source in food preparation.
Researches conducted in Brazil related to the quality of charcoal have been mainly targeted on the steel industry demand, due to stronger economic nature of charcoal which is involved in this production chain.Consequently, there are few studies focused on analysis of charcoal for the purpose of cooking and barbecue.
According to Brito (2002), Ribeiro and Vale (2006) and Rosa et al. (2012), to be considered of good quality for home use, charcoal shall meet features like high relative bulk density, high fixed carbon content, high calorific value, low moisture, low content of volatile materials and low ash content.
In United States, for instance, the studies on the quality of the barbecue charcoal and its related aspects (WARNES, 2008) PAULO, 2003).Based on voluntary membership such a stamp would be ensuring the quality of the charcoal production for barbecue based on the latter requirements.
One can cast doubt on the quality Standard pattern of charcoal for cooking, due to the difficulty of the carbonization control in most of stoves, the raw material differing from one to another in density, moisture, chemical composition, friability, mechanical resistance, reactivity and hygroscopicity.Furthermore, the result of the analysis of solid fuels should be interpreted with caution.They are influenced by the size and the shape of the material and moreover by the features of their raw material (QUIRINO; BRITO, 1991).
Despite the several underlined uncertainties about the quality definition of the charcoal for barbecue use, the enrichment of references on the issue is fundamental for the best valorization of the product regarding the end user.Thus, there is a strong probability that the grain size has a strong influence on the charcoal combustion process during the barbecue.Furthermore it has to be noticed that the packaging of the product itself, often, contains different grain size considering as powder.
In that sense the present work focused on the characterization of charcoal for barbecue purposes, mainly regarding its behavior during combustion process and the grain size influence.

Characterization of the charcoal
The charcoal was collected in a charcoal factory located in the Atibaia area in the State of São Paulo.The company produces charcoal for barbecue from Eucalyptus spp wood, in a range of seven to ten years old.The charcoal production used masonry kilns, named "rabo quente", literally "hot ass" regarding the temperature around 500 °C reached in the main phase of the combustion process.Twenty bags of 2.5 kg of charcoal were collected, from those that would be distributed in the retail sector.
Working with packaged charcoal for the retailers ensured the randomness of the sampling and let us approach as much as possible what the end user get.With regard to initial characterization of the product, some analyzes were performed by following these rules: Granulometric influence on the combustion...  Moisture content (%) -NBR 8112 (ABNT, 1986).

Index of combustion of charcoal grill (ICOM cv )
The ICOM was determined using the methodology developed by Quirino and Brito (1991) for briquettes of charcoal fines.It was necessary to adapt the assay for charcoal and to set the end time of the test, as the one required for complete combustion of the material (few minutes after beginning the assay).Such an adjustment was made due to the fact charcoal has a lower density than the briquettes assessed by the authors.The rest of the procedures followed every last details of the original methodology.As part of the set, a digital thermometer to measure the temperatures reached during combustion and scale with a capacity of 2.5 kg and a precision of 0.5 g were used.
The volume of the combustor (1.25 dm³) was filled with a charcoal mass of 150 ± 10 g.The temperature and mass consumption were recorded every five minutes, from the start of the experiment, set as zero until the end of the test.The combustion index of charcoal, called ICOM cv in this research, was calculated according to Eq. 1.
(Eq. 1) Where: A= is a percentage corresponding to the test time in which the temperature remained above 150 °C on the total time (min) of combustion (%); B= is the percentage of the maximum temperature reached in the test compared to 150 °C (%); C= is the percentage of the total mass consumed generating temperatures above 150 °C.
Observation: Conformed to the original methodology, the temperature of 150 °C is the minimum one required to start the cooking process on a barbecue, comprising the food dewatering stage.
In order to simulate everyday household situations that may be encountered during barbecue (combining several charcoal particle sizes in a single package), charcoal was passed in five different sieves with particle size mesh 8, 16, 32 and 50 mm in adequation with the volume capacity of the combustor.
The data obtained from the combustion experiment were submitted to the Kolmogorov-Smirnov test at a significance level of 5% to check the standard distribution of the data.The nearness of variances was checked to the same level of significance applying the Levene's test, whose one of the assumptions of variance analysis is that the variances are equal in the analyzed category.Once corroborated, the tests were driven following a completely randomized design with five replicates per treatment (sizing).The variance analysis was carried out with the aid of Minitab ® 16 software and the Scott-Knott test at 5% significance level was used as multiple comparison test.

Characteristics of the charcoal
Table 1 shows the average values obtained for the tests conducted to characterize the charcoal.

Combustion index (ICOM cv )
Analyzing the behavior of charcoal during combustion in Figure 1, one can observed that the maximum temperature reached varied according to grain size and showed the same tendency once plot over time.The average values contained in Table 2 show statistically differences.
The Figure 2 illustrates the mass consumption during combustion.Note that the particle size of 50 mm charcoal consumed a smaller mass percentage during the assay and more uniform mass loss.Paula et al. (2011) evaluating charcoal ICOM of unknown grain size, observed as well the uniformity along of the burning and of the material weight loss.
The Figure 3 presents the average values for a charcoal ICOM cv got from well-known grains size.

Characteristics of the charcoal
The results of the analysis of charcoal have permitted to feature it as a classical product with regular for barbecue characteristics for the consumer market.A high coefficient of variation for the ash content was DIAS JÚNIOR, A.F. et al noticed, however Trugilho et al. (2005) report it as usual for this kind of product and probably related to multiple factors.The other analyzed characteristics are consistent with the values obtained by Brito et al. (1982), Quirino andBrito (1991), São Paulo (2003)

Index of combustion
The Figure 1 and Table 2 report that the 16 mm grain size charcoal had the highest maximum temperature, while the 50 mm particle size one showed the lowest one.In the statistical field, the 8, 32 and 50 mm grain sizes of charcoal are grouped together, as differing from the others.The maximum temperature value for the 50 mm grain size can be related to its dimension.Indeed, under such size there are less contact between parts, giving a much less efficient energy transfer between them not allowing to constitute the "block continuous" of mass combustion generally expected with smaller grain size.Practically, in the 50 mm case, parts are burning individually, disconnected from the heat supply.
Granulometric influence on the combustion...As Figure 2 shows, even with a low mass consumption, the largest charcoal grains (50 mm) have a similar tendency as particles from other sizes, even if it takes it more time to lose mass during heating generation.According to Quirino and Brito (1991), for cooking use, it is interesting to maintain a given constant temperature, even if inappropriate in case of abrupt changes, which may foster frequent interferences in the process, for example feeding the combustion to keep it.
It can be also noticed that the 8, 16 and 32 mm charcoal grain size degradated between 70 and 75 minutes Valores médios seguidos pela mesma letra na coluna não diferem entre si, pelo teste de Scott-Knott a 5% de significância.
after starting the test, whereas the larger grain size charcoal (50 mm) achieved complete degradation only after 120 minutes duration of the test.
It is interesting to analyze the values of ICOM cv from the perspective of the combustion behavior illustrated in Figure 1, which represents the references of temperature versus time.It is to note that maintaining the temperature above 150 °C is highly relevant considering Equation 2. In fact, the 16 mm grain size charcoal present clearly the largest area under a curve (Figure 1) and therefore the greatest ICOM cv .
As shown in Figure 3, the ICOM cv values for the grain sizes of 8, 16 and 32 mm are in agreement with the values obtained by Quirino and Brito (1991).The authors found values from 0.31 to 1.23.It is observed that the highest value of ICOM cv was for charcoal grain size of 16 mm.From which one can deduce that the higher the ICOM cv , the greater the heat generation with the least fuel consumption mass relative to a given time.
In general, if a fuel releases enough energy (heat quantity) during combustion, but, counterpart, consumes too much mass to generate this energy, its ICOM will be lower.This occurred for charcoal with a 8 mm grain size, which showed ICOM cv lower than 16 mm grain size charcoal, despite the differences between them were not statistically significant.The charcoal with the grain size of 32 mm occured with the third ICOM cv value.Mass Consumption (%) DIAS JÚNIOR, A.F. et al When the combustion refers to charcoal with large particle sizes, as with the 50 mm charcoal, the ICOM cv value got significantly lower than the others.It let infer that due to the size of its parts, the contact between them was very small, which probably would have lessened the energy transfer throughout the mass under combustion.Despite slower mass loss rate (Figure 2), on the other hand, the temperature ranged in most of the case, below the minimum one required for use in barbecue.
The results of research provide us with the direction that, in fact, there would be arguments for considering the grain size of charcoal as an important characteristic in the product qualification proposition for use in barbecue.Similarly, by controlling the granulometry could be proposed to define the choice of charcoal, depending on the type of behavior that is desired during cooking, commanded by type of heat needs to be demanded by the food being prepared.This aspect opens up the prospect of new researches in the area, combining the quality of the charcoal and the type of cooking that it will be required.

CONCLUSION
The analyzed charcoal had regular features for use in barbecue.In the combustion test, the charcoal of 16 mm grain size was the one with the highest maximum temperature and the highest value of ICOM cv .Charcoal 50 mm had the worst behavior in the combustion test.
It is then recommended for the combustion tests of charcoal used for barbecue to establish a grain size standard and test time for a better evaluation of the material.
longstanding exist.In Europe, the "Association Française de Normalisation-AFNOR" established in 2005 a standard defined as "Appliances, solid combustibles and charcoal lighter for barbecue" describing quality issues for charcoal and briquettes used for barbecue.In Brazil, the only official proposal covering specifically charcoal quality control for barbecue, comes from the Secretariat of Agriculture and Supply of São Paulo State.Named "Selo São Paulo -Carvão Premium" (Sao Paulo Seal -Premium Quality Charcoal), it has been enacted by Resolution NÚ. 10 SAA of 11 July 2003.It aims to establish a quality standard for household charcoal, whose indicators among others are moisture, fixed carbon content, volatile material content, ash content, size of parts, labor needed (SÃO

Figure 1 -
Figure 1 -Variation of temperature versus time during the combustion.Figura 1 -Variação da temperatura em função do tempo durante o teste de combustão.

Figure 3 -
Figure 3 -Combustion index of analyzed grain sizes.Average values with same letter in the bar chart do not differ in the Scott-Knott test with a 5% significance.Figura 3 -Índice de combustão das granulometrias analisadas.Valores médios seguidos pela mesma letra na coluna não diferem entre si, pelo teste de Scott-Knott a 5% de significância.