ABSTRACT
The objective of this work was to evaluate the performance accuracy of digital elevation models in delimiting a water basin located in the relief transition region between the São Francisco Plateau, São Franciscana Depression and the Espinhaço mountain range. Four digital elevation models with data from the Shuttle Radar Topographic Mission (SRTM) and map topography were generated using the Topo To Raster interpolator with and without support from hydrography maps (IBGE), and another with the original SRTM data. For each digital elevation model, its accuracy was evaluated for representing: the drainage, the hydrography and basin mouth in comparison to the references obtained from IBGE maps. The models generated with SRTM and topographic data supported by hydrography maps showed good performance, with small delimitation errors in the water basin. Those generated without support from hydrography maps showed gross errors due to non-representation of the hydrography in the São Franciscana Depression region.
Keywords:
SRTM; topographic maps; interpolation
1. INTRODUCTION
A water basin is understood as a natural catchment area of precipitation, topographically delimited by a water divider which converges flows to a single outlet called the mouth (Ferrari et al., 2013Ferrari JL, Silva SF, Santos AR, Garcia RF. Análise morfométrica da sub-bacia hidrográfica do córrego Horizonte, Alegre, ES. Agrária 2013; 8(2): 181-188. http://dx.doi.org/10.5039/agraria.v8i2a1575.
http://dx.doi.org/10.5039/agraria.v8i2a1...
). A water basin is of fundamental importance for water resources, as they are the planning and management units adopted by the National Water Resources Policy, instituted by Law No. 9,433 from January 8, 1997.
A basin must be identified and delimited following the dynamics and conformation of the drainage network to which it is connected (Bertoni & Lombardi, 2008Bertoni J, Lombardi F No. Conservação do solo. 6. ed. São Paulo: Ícone; 2008.; Ferrari et al., 2013Ferrari JL, Silva SF, Santos AR, Garcia RF. Análise morfométrica da sub-bacia hidrográfica do córrego Horizonte, Alegre, ES. Agrária 2013; 8(2): 181-188. http://dx.doi.org/10.5039/agraria.v8i2a1575.
http://dx.doi.org/10.5039/agraria.v8i2a1...
). Correct delimitation of its water dividers and its drainage network is of great importance for studies related to modeling flows, erosive processes, transport and deposition of chemical pollutants, as well as in predicting floods and understanding geomorphological, geological and pedological issues (Ceballos & Schnabel, 1998Ceballos A, Schnabel S. Hydrological behavior of a small catchment in the dehesa landuse system (Extremadure, SW Spain). Journal of Hydrology 1998; 210(1-4): 146-160. http://dx.doi.org/10.1016/S0022-1694(98)00180-2.
http://dx.doi.org/10.1016/S0022-1694(98)...
; Ribeiro et al., 2005Ribeiro C, Pires J, Nascimento M, Santana R. Análise da exatidão de diferentes métodos de interpolação para geração de modelos digitais de elevação e obtenção de características morfométricas em bacias hidrográficas. Revista Brasileira de Recursos Hídricos 2005; 10(2): 39-47. http://dx.doi.org/10.21168/rbrh.v10n2.p39-47.
http://dx.doi.org/10.21168/rbrh.v10n2.p3...
), and should be the first step in the representation of the study area (Seyler et al., 2009Seyler F, Muller F, Cochonneau G, Guimarães L, Guyot JL. Watershed delineation for the Amazon sub-basin system using GTOPO30 DEM and a drainage network extracted from JERS SAR images. Hydrological Processes 2009; 23(22): 3173-3185. http://dx.doi.org/10.1002/hyp.7397.
http://dx.doi.org/10.1002/hyp.7397...
).
Delimiting water basins has been performed automatically using the tools available in most Geographic Information Systems (GIS) (Garbrecht & Martz, 1993Garbrecht J, Martz LW. Network and subwatershed parameters extracted from digital elevation models: the bills creek experience. Journal of the American Water Resources Association 1993; 29(6): 909-916. http://dx.doi.org/10.1111/j.1752-1688.1993.tb03251.x.
http://dx.doi.org/10.1111/j.1752-1688.19...
; Ribeiro et al., 2005Ribeiro C, Pires J, Nascimento M, Santana R. Análise da exatidão de diferentes métodos de interpolação para geração de modelos digitais de elevação e obtenção de características morfométricas em bacias hidrográficas. Revista Brasileira de Recursos Hídricos 2005; 10(2): 39-47. http://dx.doi.org/10.21168/rbrh.v10n2.p39-47.
http://dx.doi.org/10.21168/rbrh.v10n2.p3...
). Algorithms are used in this process which identify the water dividers and hydrography from a matrix representation of the terrain’s topography, called the Digital Elevation Model (DEM) (Fairfield & Leymarie, 1991Fairfield J, Leymarie P. Drainage networks from grid digital elevation models. Water Resources Research 1991; 27(5): 709-717. http://dx.doi.org/10.1029/90WR02658.
http://dx.doi.org/10.1029/90WR02658...
; Choi & Engel, 2003Choi JY, Engel BA. Real-time watershed delineation system using Web-GIS. Journal of Computing in Civil Engineering 2003; 17(3): 189-196. http://dx.doi.org/10.1061/(ASCE)0887-3801(2003)17:3(189).
http://dx.doi.org/10.1061/(ASCE)0887-380...
; Alves et al., 2010Alves T So, Oliveira PTS, Rodrigues DBB, Ayres FM. Delimitação automática de bacias hidrográficas utilizando dados SRTM. Engenharia Agrícola 2010; 30(1): 46-57. http://dx.doi.org/10.1590/S0100-69162010000100005.
http://dx.doi.org/10.1590/S0100-69162010...
; Cecílio et al., 2013Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
).
Using DEM to obtain the drainage network and to delineate basins was stimulated from developing the algorithm Deterministic-8Node (D8) (O’Callaghan & Mark, 1984O’Callaghan JF, Mark DM. The extraction of drainage networks from digital elevation data. Computer Vision Graphics and Image Processing 1984; 28(3): 323-344. http://dx.doi.org/10.1016/S0734-189X(84)80011-0.
http://dx.doi.org/10.1016/S0734-189X(84)...
; Seyler et al., 2009Seyler F, Muller F, Cochonneau G, Guimarães L, Guyot JL. Watershed delineation for the Amazon sub-basin system using GTOPO30 DEM and a drainage network extracted from JERS SAR images. Hydrological Processes 2009; 23(22): 3173-3185. http://dx.doi.org/10.1002/hyp.7397.
http://dx.doi.org/10.1002/hyp.7397...
). This algorithm determines that in a grid of cells which represent the altimetric relief values, water flow happens from each cell to one of its eight neighbors (orthogonal and diagonal) in the direction of the highest slope (Ribeiro et al., 2005Ribeiro C, Pires J, Nascimento M, Santana R. Análise da exatidão de diferentes métodos de interpolação para geração de modelos digitais de elevação e obtenção de características morfométricas em bacias hidrográficas. Revista Brasileira de Recursos Hídricos 2005; 10(2): 39-47. http://dx.doi.org/10.21168/rbrh.v10n2.p39-47.
http://dx.doi.org/10.21168/rbrh.v10n2.p3...
).
DEMs are currently obtained through remote sensor images (radars) or from interpolating topographic data points and contour lines extracted from topographic maps or planialtimetric surveys (Pinheiro, 2006Pinheiro ES. Comparação entre dados altimétricos Shuttle Radar Topography Mission, cartas topográficas e GPS: Numa área com relevo escarpado. Revista Brasileira de Cartografia 2006; 58(1): 1-9.; Oliveira et al., 2010Oliveira PTS, Alves T So, Steffen JL, Rodrigues DBB. Caracterização morfométrica de bacias hidrográficas através de dados SRTM. Revista Brasileira de Engenharia Agrícola e Ambiental 2010; 14(8): 819-825. http://dx.doi.org/10.1590/S1415-43662010000800005.
http://dx.doi.org/10.1590/S1415-43662010...
; Cecílio et al., 2013Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
). Depending on the DEM characteristics such as scale, resolution and origin, automatic delimitation of a basin may differ significantly (Ribeiro et al., 2005Ribeiro C, Pires J, Nascimento M, Santana R. Análise da exatidão de diferentes métodos de interpolação para geração de modelos digitais de elevação e obtenção de características morfométricas em bacias hidrográficas. Revista Brasileira de Recursos Hídricos 2005; 10(2): 39-47. http://dx.doi.org/10.21168/rbrh.v10n2.p39-47.
http://dx.doi.org/10.21168/rbrh.v10n2.p3...
; Alcaraz et al., 2009Alcaraz SA, Sannier C, Vitorino ACT, Daniel O. Comparison of methodologies for automatic generation of limits and drainage networks for hidrographic basins. Revista Brasileira de Engenharia Agrícola e Ambiental 2009; 13(4): 369-375. http://dx.doi.org/10.1590/S1415-43662009000400001.
http://dx.doi.org/10.1590/S1415-43662009...
; Seyler et al., 2009Seyler F, Muller F, Cochonneau G, Guimarães L, Guyot JL. Watershed delineation for the Amazon sub-basin system using GTOPO30 DEM and a drainage network extracted from JERS SAR images. Hydrological Processes 2009; 23(22): 3173-3185. http://dx.doi.org/10.1002/hyp.7397.
http://dx.doi.org/10.1002/hyp.7397...
; Medeiros et al., 2009Medeiros LC, Ferreira NC, Ferreira LG. Avaliação de modelos digitais de elevação para delimitação automática de bacias hidrográficas. Revista Brasileira de Cartografia 2009; 61(2): 137-151.; Cecílio et al., 2013Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
; Rawat et al., 2014Rawat KS, Krishna G, Mishra A, Singh J, Mishra SV. Effect of DEM data resolution on low relief region sub-watershed boundaries delineating using of SWAT model and DEM derived from CARTOSAT-1 (IRS-P5), SRTM and ASTER. Journal of Applied and Natural Science 2014; 6(1): 144-151. http://dx.doi.org/10.31018/jans.v6i1.391.
http://dx.doi.org/10.31018/jans.v6i1.391...
).
Ribeiro et al. (2005)Ribeiro C, Pires J, Nascimento M, Santana R. Análise da exatidão de diferentes métodos de interpolação para geração de modelos digitais de elevação e obtenção de características morfométricas em bacias hidrográficas. Revista Brasileira de Recursos Hídricos 2005; 10(2): 39-47. http://dx.doi.org/10.21168/rbrh.v10n2.p39-47.
http://dx.doi.org/10.21168/rbrh.v10n2.p3...
compared the quality and accuracy of DEMs generated by IDW, SPLINE and TOPOGRID interpolators and obtained better results with TOPOGRID and SPLINE. Cecílio et al. (2013)Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
evaluated the automatic delimitation of a river basin located in a mountainous region from six different DEMs: three DEMs originating from radar imaging (SRTM) and their refinements; and three DEMs originating from spatial interpolation processes of contour lines. The authors verified that the DEM generated from the contour lines and hydrography mapped using the Topo To Raster interpolator better represented the basin relief for delimitation purposes. Rawat et al. (2014)Rawat KS, Krishna G, Mishra A, Singh J, Mishra SV. Effect of DEM data resolution on low relief region sub-watershed boundaries delineating using of SWAT model and DEM derived from CARTOSAT-1 (IRS-P5), SRTM and ASTER. Journal of Applied and Natural Science 2014; 6(1): 144-151. http://dx.doi.org/10.31018/jans.v6i1.391.
http://dx.doi.org/10.31018/jans.v6i1.391...
evaluated the effects of DEM resolution on delimiting the water dividers of a sub-basin in Shahjahanpur, India. The authors evaluated a DEM with a resolution of 2.6 m (DEM CARTOSAT-1), one with a resolution of 30 m (ASTER DEM) and another with a resolution of 90 m (SRTM DEM). They obtained a better accuracy in delimiting the basin with the resolution of 2.6 m, and much better precision with that of 90 m in comparison to the one with greater spatial resolution (30 m).
Considering the above, we have not found any studies evaluating DEM performance obtained by different techniques in relief transition regions. Thus the objective of this work was to evaluate the accuracy of digital elevation models generated from SRTM data and topographic charts using different techniques in delimiting a river basin located in a transition region between the São Francisco Plateau, São Franciscana Depression and Espinhaço mountain range in Minas Gerais state, Brazil.
2. MATERIAL AND METHODS
2.1. Study area
The study was conducted for the Peixe River water basin, which has a drainage area of approximately 580 km2 located in one of the most important hydrographic basins of the country, the São Francisco River. It is located in the central region of Minas Gerais state, between the coordinates of 19°25’00” and 19°42’00” S and 44°40’00” and 45°00’00” W, in a transition region between the São Francisco Plateau, the São Franciscana Depression and the Espinhaço mountain range (Figure 1). The basin covers the municipalities of Pitangui, Onça do Pitangui, Pompeu, Maravilhas and Papagaio.
The São Francisco Plateau consists of tabular surfaces called chapadas, with predominantly sandy sedimentary cover bordered by erosive ridges well-marked in the landscape and intersected by deep drainage headwaters known as waterpaths. The tabular reliefs are distinguished in two levels of altitude: one ranging from 800 to 1000 m, and the other from 600 to 800 m (IGA, 2016Instituto de Geociências Aplicadas – IGA. Atlas digital de Minas Gerais: geomorfologia [online]. Belo Horizonte: IGA; 2016 [cited 2016 May 20]. Available from: http://www.iga.mg.gov.br/mapserv_iga/atlas/TutorialPDF/7-Geomorfologia.pdf
http://www.iga.mg.gov.br/mapserv_iga/atl...
).
The São Franciscana Depression develops along the São Francisco River drainage, where flattened relief forms, wavy surfaces and ragged pediments predominate. The extensive recessed areas show prevailing altitudes around 500 m. The landscape shows more rugged relief close to the Espinhaço mountain range, where hills and crests with ravined slopes and embedded valleys predominate (IGA, 2016Instituto de Geociências Aplicadas – IGA. Atlas digital de Minas Gerais: geomorfologia [online]. Belo Horizonte: IGA; 2016 [cited 2016 May 20]. Available from: http://www.iga.mg.gov.br/mapserv_iga/atlas/TutorialPDF/7-Geomorfologia.pdf
http://www.iga.mg.gov.br/mapserv_iga/atl...
).
The Espinhaço mountain range is a large water divider interposed between the central-east Brazil basins and that of the São Francisco River. In Minas Gerais, it constitutes a set of uplands with a boomerang form in the general north-south direction with convexity orientated to the west (Saadi, 1995Saadi A. A geomorfologia da Serra do Espinhaço em Minas Gerais e de suas margens. Geonomos 1995; 3(1): 41-63.) with predominance of crests, peaks, and embedded valleys, as well as slightly wavy relief forms to a lesser extent (Sodré et al., 2007Sodré RVR, Carvalho AO Jr, Machado WP, Oliveira SN, Gomes RAT, Guimarães RF. Classificação de bacias de drenagem do Alto Jequitaí (Minas Gerais) a partir da análise de principais componentes e análise de grupos. Revista Brasileira de Geomorfologia 2007; 8(2): 73-86. http://dx.doi.org/10.20502/rbg.v8i2.95.
http://dx.doi.org/10.20502/rbg.v8i2.95...
).
The region’s climate is Cwa (mesothermic tropical altitude) according to the Köppen classification, presenting dry winters and mild summers with an average lower than 19 °C in the coldest month. The predominant vegetation is medium-sized cerrado, with patches of perennial forests and semi-deciduous occurring (Romano & Soares, 2007Romano AW, Soares ACP. Geologia da folha Pará de Minas SE.23-Z-C-IV. Belo Horizonte: CPRM; 2007.). The soils present in the basin are: Red Latosol; Red-yellow Latosol; Red Argisol and Red-yellow Argisol (IBGE, 2002Instituto Brasileiro de Geografia e Estatística – IBGE. Mapa de solos do Brasil [online]. Rio de Janeiro: IBGE; 2002 [cited 2015 July 17]. Available from: ftp://geoftp.ibge.gov.br/mapas_tematicos/mapas_murais/solos.pdf).
2.2. Delimitation of water dividers, representation of the hydrography and mouth
Delimiting the water dividers, as well as the representativeness of the water basin’s hydrography and mouth, was performed via five different digital elevation models obtained from different techniques (Table 1). Three of these models were elaborated based on the matrix representation obtained by radar interferometry called Shuttle Radar Topography Mission (SRTM) (Rabus et al., 2003Rabus B, Eineder M, Roth A, Bamler R. The shuttle radar topography mission – a new class of digital elevation models acquired by spaceborne radar. ISPRS Journal of Photogrammetry and Remote Sensing 2003; 57(4): 241-262. http://dx.doi.org/10.1016/S0924-2716(02)00124-7.
http://dx.doi.org/10.1016/S0924-2716(02)...
). The other two were obtained from interpolating the contour lines obtained from planialtimetric maps from the Brazilian Institute of Geography and Statistics (IBGE), in the scale of 1:100,000. The IBGE planialtimetric maps have information on hydrography (mapped) and altimetry (50 m equidistance contour lines) referring to the Pará de Minas (042533) and Pompeu (042495) sheets, available in vector format. It should be noted that this scale was used because these data are not available on a larger scale.
Digital elevation models assessed in delimiting water dividers, hydrography and the mouth of the Peixe River water basin.
SRTM data were obtained from the Brazilian Agricultural Research Corporation (EMBRAPA), with a spatial resolution of 90 × 90 m and WGS84 datum. One DEM was elaborated from the original SRTM matrix representation. The other two were obtained by adapting the methodology of Valeriano & Abdon (2007)Valeriano MM, Abdon MM. Aplicação de dados SRTM a estudos do Pantanal. Revista Brasileira de Cartografia 2007; 59(1): 63-71., described as: first, contour lines with equidistance of 20 m were generated from the SRTM for the entire length of the basin; next, the contour lines were interpolated through the Topo To Raster interpolator with and without the IBGE hydrography support (mapped), respectively generating the DEMs denominated SRTM-TRH and SRTM-TR, both with spatial resolution of 10 × 10 m (Table 1). It should be noted that the DEMs were previously georeferenced using the ArcGis 9.3 georeferencing extension, adjusting the raster image (DEM) to the georeferenced mesh (vector file.dgn) using the Auto Adjust and 1st order polynomial error, observing an acceptable limit of 10 for the total RMS Error.
The other DEMs were obtained by interpolating the IBGE map contour lines using the Topo To Raster interpolator with and without mapped hydrography support, respectively generating the DEMs denominated TM-TRH and TM-TR, both with spatial resolution of 10 × 10 m (Table 1). It should be noted that choosing the Topo To Raster interpolator was based on the results obtained in other studies that proved its effectiveness in interpolating data.
ArcGIS 9.3 software (ESRI, 2008Environmental Systems Research Institute – ESRI. ArcGIS Professional GIS for the desktop. version 9.3 [software]. Redlands: ESRI; 2008.) was used in order to obtain the DEMs from different techniques, as well as for the automatic delimitation of the water dividers, for the hydrographic representation and the mouth of the water basin, which were determined using the Spatial Analyst and Hydrology Modeling extensions and based on the Deterministic-8Node algorithm (O’Callaghan & Mark, 1984O’Callaghan JF, Mark DM. The extraction of drainage networks from digital elevation data. Computer Vision Graphics and Image Processing 1984; 28(3): 323-344. http://dx.doi.org/10.1016/S0734-189X(84)80011-0.
http://dx.doi.org/10.1016/S0734-189X(84)...
). Firstly, spurious depressions (cells surrounded by others with higher elevation values) were identified and eliminated (which can cause distortions in the drainage network and make it impossible to trace the water dividers) (Oliveira et al., 2010Oliveira PTS, Alves T So, Steffen JL, Rodrigues DBB. Caracterização morfométrica de bacias hidrográficas através de dados SRTM. Revista Brasileira de Engenharia Agrícola e Ambiental 2010; 14(8): 819-825. http://dx.doi.org/10.1590/S1415-43662010000800005.
http://dx.doi.org/10.1590/S1415-43662010...
) using the Fill Sinks command. Next, the flow directions were defined using the Flow Direction command, the accumulated flow (Flow Accumulation command) and the automatic delimitation of the basin (Watershed command). The hydrography was generated from the accumulated flow, adopting a value of 500 in the Raster Calculator tool as the minimum number of cells for flow generation denominated numerically.
2.3. Evaluation of Digital Elevation Models (DEMs)
In order to evaluate the accuracy of the DEMs obtained by different techniques, delimitations of the water dividers, the hydrographic representation and the Peixe River water basin mouth were determined from each DEM and compared with their references: the delimitation of the water dividers performed manually from topographic charts, and the hydrography and mapped data obtained from IBGE. ArcGIS 9.3 software and topographic maps mentioned above were used to this purpose.
The accuracy of the DEM was evaluated by submitting each DEM to the following criteria (Ribeiro et al., 2005Ribeiro C, Pires J, Nascimento M, Santana R. Análise da exatidão de diferentes métodos de interpolação para geração de modelos digitais de elevação e obtenção de características morfométricas em bacias hidrográficas. Revista Brasileira de Recursos Hídricos 2005; 10(2): 39-47. http://dx.doi.org/10.21168/rbrh.v10n2.p39-47.
http://dx.doi.org/10.21168/rbrh.v10n2.p3...
; Pinheiro, 2006Pinheiro ES. Comparação entre dados altimétricos Shuttle Radar Topography Mission, cartas topográficas e GPS: Numa área com relevo escarpado. Revista Brasileira de Cartografia 2006; 58(1): 1-9.; Lindsay et al., 2008Lindsay JB, Rothwell JJ, Davies H. Mapping outlet points used for watershed delineation onto DEM-derived stream networks. Water Resources Research 2008; 44(8): W08442. http://dx.doi.org/10.1029/2007WR006507.
http://dx.doi.org/10.1029/2007WR006507...
; Cecílio et al., 2013Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
; Rawat et al., 2014Rawat KS, Krishna G, Mishra A, Singh J, Mishra SV. Effect of DEM data resolution on low relief region sub-watershed boundaries delineating using of SWAT model and DEM derived from CARTOSAT-1 (IRS-P5), SRTM and ASTER. Journal of Applied and Natural Science 2014; 6(1): 144-151. http://dx.doi.org/10.31018/jans.v6i1.391.
http://dx.doi.org/10.31018/jans.v6i1.391...
): a) minimum and maximum altitude and relative error in determining the drainage area; b) error in the water basin’s mouth location obtained from the location difference in a straight line; c) visual comparison between mapped and numerical hydrography (obtained with the DEM); and d) visual comparison between the reference water dividers and the dividers obtained from the DEM. It should be noted that the relative error was obtained by the difference (in the module) between the reference value and that obtained with the DEM, divided by the reference value.
3. RESULTS AND DISCUSSION
Table 2 shows the drainage areas and the minimum and maximum altitudes obtained automatically by means of the different evaluated DEMs, and manually by reference.
Drainage area (Ad) and minimum (Amin) and maximum (Amax) altitudes of the Peixe River Water Basin obtained automatically by the DEM and manually (reference).
In general, we obtained the best results with the models generated using mapped hydrography support (SRTM-TRH and TM-TRH) (Table 2). Considering only the drainage area of the basin, the model that presented the best estimates was generated from the SRTM data using the Topo To Raster interpolator with the mapped hydrography support (SRTM-TRH). It has an estimation error of 0.4% compared to that obtained from the reference delimitation (578.8 km2), which shows the accuracy of this technique for obtaining the DEM. Cecílio et al. (2013)Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
obtained an error of only 0.04% in evaluating different DEMs in delimitating the Prata River Basin, Espírito Santo state, obtaining the drainage area using the TM-TRH DEM, which was considered by the authors as having the best performance for delimiting the basin. In the present study, although it was not the best DEM for delimiting the basin, good estimates were also obtained with the TM-TRH DEM with a relative error of only 1.1%, also proving the accuracy of the technique for obtaining this DEM. It should be noted that these differences found between the studies are associated to the different topographic characteristics between the basins, especially with respect to the flat areas, which are lower in the case of the basin used by Cecílio et al. (2013)Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
than in this study.
In using the DEMs generated without the hydrography support (SRTM-O, SRTM-TR and TM-TR), it can be observed that good estimates were not obtained in delimiting the Peixe River Basin, with differences in drainage area of 104.8, 104.8 and 154.8 km2 for SRTM-O, SRTM-TR and TM-TR respectively, compared to the reference delimitation, which is equivalent to relative errors of 18.1, 18.1 and 26.6% (Table 2). These values are considered high when compared to those obtained in the literature, mainly those found by Cecílio et al. (2013)Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
, who obtained errors up to 1.8% in the drainage area using these DEMs in delimiting the Prata River basin. It should be noted that the authors tested the models in a mountainous region with different topographic conditions than the region of the present study, which is a transition of extensive flat area with more pronounced relief areas. Error close to the present study and also in flat relief regions was obtained by Seyler et al. (2009)Seyler F, Muller F, Cochonneau G, Guimarães L, Guyot JL. Watershed delineation for the Amazon sub-basin system using GTOPO30 DEM and a drainage network extracted from JERS SAR images. Hydrological Processes 2009; 23(22): 3173-3185. http://dx.doi.org/10.1002/hyp.7397.
http://dx.doi.org/10.1002/hyp.7397...
when evaluating SRTM DEM in delimiting sub-basins in Amazonas State in the northern region of Brazil. The authors obtained an error of 17.4% in delimiting the drainage area for one of the studied basins.
Regarding the maximum and minimum altitude values, the best estimate was also observed when using SRTM-TRH DEM. We obtained a difference of 1 and 15 m in the minimum and maximum altitude for this model, respectively, in comparison to the reference. The worst estimate was observed using the TM-TR model, with a difference of 21 and 25 m in the minimum and maximum altitude, respectively. Adequate estimation of the minimum altitude is of fundamental importance for delimiting the basin since it is directly related to its mouth, and errors in its estimation can cause great errors in delimiting basins, which was verified in the present study in using DEM generated without mapped hydrography support (Figures 222e).
Location of the real Peixe River Water Basin mouth and those obtained using the various evaluated Digital elevation models (DEMs).
Figure 2a shows the Peixe River Basin inserted between the Espinhaço mountain range, São Francisco Plateau and São Franciscana Depression. Figures 22f show the location of the Peixe River basin mouth, delimited from the evaluated DEMs and the manual procedure (reference). It is emphasized that the reliefs were not inserted in Figures 22f for clarity.
As with determining the drainage area and the altitudes (minimum and maximum), the errors verified in determining the basin’s mouth were smaller when using the DEM generated with the mapped hydrography support (Figures 22f), which are visually imperceptible. A large difference between the actual mouth and those obtained using the DEM without the mapped hydrography support (Figures 222e) is also visually observed. Considering a straight line, the difference in location between the actual mouth and those generated automatically were: 9,303.3 m for SRTM-O; 9,179.1 m for SRTM-TR; 10,606.2 m for TM-TR; 165.0 m for TM-TRH; and 13.1 m for SRTM-TRH. The differences in the actual mouth location and those obtained with the DEMs without the hydrography support are large, mainly when compared to those found by Cecílio et al. (2013)Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
for the Prata River basin, Espírito Santo state. These authors found a location difference of 614, 421 and 71 m between the actual basin mouth and those generated using SRTM-O, SRTM-TR and TM-TR, respectively.
According to Cecílio et al. (2013)Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
, the errors made in determining the mouth are associated with hydrography mischaracterization by using a simulation of rectilinear water courses in flatter areas. This observation made by the authors was verified in the present study, as can be observed in Figures 222e. Note that the hydrography generated with SRTM-O (2b), SRTM-TR (2c) and TM-TR (2e) cuts the real water divider of the basin. It diverts the Peixe River (main river from the basin) to a neighboring basin due to the mischaracterization of the numerical hydrograph (generated with the DEMs) in the São Franciscana Depression region, as can be verified when comparing the respective figure with Figure 2a. However (Figures 33f), by using the DEMs generated with mapped hydrography support (Figures 33f), we can see a good fit of the numerical hydrograph to the mapped one by the overlapping hydrographs. These results demonstrate the accuracy and the necessity of using mapped hydrography as a support to generate the DEM in order to force the Topo To Raster algorithm to generate the numerical hydrograph with greater precision in the São Franciscana Depression region, as its flattened relief form hinders better characterization. Other studies also suggest that hydrography be used as a support to strengthen the drainage network location of a basin (Fairfield & Leymarie, 1991Fairfield J, Leymarie P. Drainage networks from grid digital elevation models. Water Resources Research 1991; 27(5): 709-717. http://dx.doi.org/10.1029/90WR02658.
http://dx.doi.org/10.1029/90WR02658...
; Ribeiro et al., 2005Ribeiro C, Pires J, Nascimento M, Santana R. Análise da exatidão de diferentes métodos de interpolação para geração de modelos digitais de elevação e obtenção de características morfométricas em bacias hidrográficas. Revista Brasileira de Recursos Hídricos 2005; 10(2): 39-47. http://dx.doi.org/10.21168/rbrh.v10n2.p39-47.
http://dx.doi.org/10.21168/rbrh.v10n2.p3...
; Cecílio et al., 2013Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
).
Main errors made in delimiting the Peixe River Basin water dividers using the Shuttle Radar Topography Mission original (SRTM-O DEM).
Figure 3a shows the clearest errors made using the SRTM-O DEM in delimiting the Peixe River Basin water dividers, which is inserted in the transition region between the São Francisco Plateau, São Franciscana Depression and Espinhaço mountain range. These errors are presented in greater detail in Figures 333d, emphasizing that the relief information was not inserted for clarity.
Three of the clearest errors in basin delineation using the SRTM-O DEM compared to the reference (actual water divider) are shown in Figure 3a. A large part of the drainage area and the hydrography of the neighboring basin (number 1 – Figure 3b) are also included, as well as the exclusion of a large part of the basin drainage area towards the mouth (number 2 – Figure 3c). These errors were caused due to a gross error in which the main river of the basin (Peixe River) was cut by the water dividers delimited with this DEM in the São Franciscana Depression region, as can be visualized by comparing Figures 33c. Small inclusion and exclusion errors of drainage areas (number 3) can also be observed (Figure 3d) in areas of the São Franciscana Depression and in the São Francisco Plateau (Figure 3a). Based on these errors (1 and 2) and on the large errors made in determining the drainage area and the location of the Peixe River basin mouth, it can be inferred that SRTM-O presented poor performance and should not be used for studies in the region.
The errors found between the reference delimitation and that obtained with the elevation model generated from the SRTM without the hydrographic mapped support (SRTM-TR) can be seen in Figures 44d.
Main errors made in delimiting the Peixe River Basin water dividers using the SRTM without the hydrographic mapped support (SRTM-TR DEM).
Thus, as in SRTM-O, a large inclusion of drainage area and hydrography of the neighboring basin was observed (Figure 4b), as represented by number 1; the exclusion of a good part of the drainage area and hydrography of the basin in the mouth direction (number 2 – Figure 4c); and small inclusions and exclusions of drainage area (number 3 – Figure 4d). Errors 1 and 2 were also caused by the gross error in which the main river of the basin was cut by the water dividers delimited with this DEM in the São Franciscana Depression region (Figures 44c). Thus, it is seen that the errors made with the SRTM-TR were practically the same as with the SRTM-O. The pixel size reduction from 90 × 90 m (SRTM-O) to 10 × 10 m (SRTM-TR) interpolated by using Topo To Raster did not show improvements. Therefore the DEM obtained by this technique (just as SRTM-O) should not be used for on-site studies.
Figures 55c show the main errors in delimiting the water dividers using the SRTM-TRH DEM in comparison to the reference (actual water divider).
Main errors made in delimiting Peixe River Basin water dividers using the SRTM with the hydrographic mapped support (SRTM-TRH DEM).
One of the best results was obtained from the studied models, evidencing the technique’s effectiveness in associating the basin’s hydrography (mapped) when performing DEM interpolation. Inclusion and exclusion errors of drainage areas were few (Figures 55c), which are only limited to the São Franciscana Depression region. Therefore this corroborates the best drainage area estimate and minimum altitude of the basin (Table 2), thereby qualifying the SRTM-TRH DEM as having great precision for studies on the Peixe River water basin. The models generated with the mapped hydrography support also presented the best results in other automatic delimitation studies of water basins like those of Alcaraz et al. (2009)Alcaraz SA, Sannier C, Vitorino ACT, Daniel O. Comparison of methodologies for automatic generation of limits and drainage networks for hidrographic basins. Revista Brasileira de Engenharia Agrícola e Ambiental 2009; 13(4): 369-375. http://dx.doi.org/10.1590/S1415-43662009000400001.
http://dx.doi.org/10.1590/S1415-43662009...
, Medeiros et al. (2009)Medeiros LC, Ferreira NC, Ferreira LG. Avaliação de modelos digitais de elevação para delimitação automática de bacias hidrográficas. Revista Brasileira de Cartografia 2009; 61(2): 137-151. and Cecílio et al. (2013)Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
.
The clearest errors in delimiting the Peixe River basin are presented in Figures 66f by use of the TM-TR DEM in comparison to the reference (real water divider).
Main errors made in delimiting the Peixe River Basin water dividers using the IBGE topographic maps without mapped hydrography support (TM-TR DEM).
In addition to the greater errors in the mouth location, in estimating the drainage area and worse performance in estimating the minimum altitude of the basin (Table 2) compared to the other studied DEMs, more errors were made with this model in delimiting the basin’s water dividers (Figure 3a). The errors (1 and 2) observed with the other models generated without the mapped hydrography support were also observed (Figures 33c), because the main river of the basin (Peixe River) was cut by the water dividers delimited with this DEM. However, this occurred in a slightly higher region of the São Franciscana Depression than the SRTM-O and SRTM-TR DEMs. These errors caused by using these three DEMs serve as an alert to the academic community and water managers about the need to verify the accuracy of the DEM prior to its use, since such serious errors can compromise all the environmental planning of the basin.
Other errors which were not committed by the other models were observed using TM-TR, such as the inclusion of a good part of the area and the hydrography of another neighboring basin (number 3) in areas of the São Francisco Plateau and São Franciscana Depression (Figures 66d). There were also minor errors of including drainage area and hydrography of neighboring basins in areas of the São Francisco Plateau and Espinhaço mountain range (Figures 666f).
In other studies such as those by Ribeiro et al. (2005)Ribeiro C, Pires J, Nascimento M, Santana R. Análise da exatidão de diferentes métodos de interpolação para geração de modelos digitais de elevação e obtenção de características morfométricas em bacias hidrográficas. Revista Brasileira de Recursos Hídricos 2005; 10(2): 39-47. http://dx.doi.org/10.21168/rbrh.v10n2.p39-47.
http://dx.doi.org/10.21168/rbrh.v10n2.p3...
and Cecílio et al. (2013)Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007.
http://dx.doi.org/10.5433/1679-0359.2013...
, satisfactory results have been observed with the use of this DEM by using topographic maps at a scale of 1:50,000. The scale of the planialtimetric maps used (1:100,000) possibly influenced the delimitation errors of the basin by using this DEM a little. However it is evident that the reason for large errors is not associated with this, but to the distinct relief characteristics in which the basin is located.
Figures 77d show the main errors made using the DEM generated from IBGE topographic maps with mapped hydrography support (TM-TRH).
Main errors made in delimiting Peixe River Basin water dividers using the IBGE topographic maps with mapped hydrography support (TM-TRH DEM).
Differently from the TM-TR DEM without hydrography support, the TM-TRH DEM presented good results in estimating the Peixe River basin water dividers. However, some faults were observed such as the inclusion of a small drainage area of the neighboring basin (Figure 7d) in the São Francisco Plateau region and the exclusion of a small basin drainage area (Figures 77c) in the São Franciscana Depression.
4. CONCLUSIONS
-
i
The models generated with SRTM data and topographic maps with the mapped hydrography support presented good precision, with small basin delimitation errors. They are indicated for in situ studies;
-
ii
The models generated without the mapped hydrography support presented gross errors due to the non-representativeness of the hydrography in the São Franciscana Depression region. These errors serve as an alert for the academic community and water resource managers about the need to verify the accuracy of the DEM before use;
-
iii
The results were obtained and are valid for the scale of 1,100,000. Therefore, it is advisable to perform other studies in other relief transition regions similar or not to this study, with different scales or not, and with different SRTM resolution (cell size of 30 × 30 m) for a more solid conclusion on the accuracy of these models. It is noteworthy that the 30 m SRTM DEM is available for download on the USGS website (NASA, 2018National Aeronautics and Space Administration – NASA. Shuttle radar topography mission [online]. Washington; 2018 [cited 2018 July 6]. Available from: http://www2.jpl.nasa.gov/srtm/index.html
http://www2.jpl.nasa.gov/srtm/index.html... ).
ACKNOWLEDGEMENTS
The authors would like to thank FAPEMIG for granting a scholarship to the first author, which was fundamental for the accomplishment of the work.
REFERENCES
- Alcaraz SA, Sannier C, Vitorino ACT, Daniel O. Comparison of methodologies for automatic generation of limits and drainage networks for hidrographic basins. Revista Brasileira de Engenharia Agrícola e Ambiental 2009; 13(4): 369-375. http://dx.doi.org/10.1590/S1415-43662009000400001
» http://dx.doi.org/10.1590/S1415-43662009000400001 - Alves T So, Oliveira PTS, Rodrigues DBB, Ayres FM. Delimitação automática de bacias hidrográficas utilizando dados SRTM. Engenharia Agrícola 2010; 30(1): 46-57. http://dx.doi.org/10.1590/S0100-69162010000100005
» http://dx.doi.org/10.1590/S0100-69162010000100005 - Bertoni J, Lombardi F No. Conservação do solo 6. ed. São Paulo: Ícone; 2008.
- Ceballos A, Schnabel S. Hydrological behavior of a small catchment in the dehesa landuse system (Extremadure, SW Spain). Journal of Hydrology 1998; 210(1-4): 146-160. http://dx.doi.org/10.1016/S0022-1694(98)00180-2
» http://dx.doi.org/10.1016/S0022-1694(98)00180-2 - Cecílio RA, Coutinho LM, Xavier AC, Moreira MC, Zanetti SS, Garcia GO. Delimitação de bacia hidrográfica em região montanhosa a partir de diferentes modelos digitais de elevação. Semina: Ciências Agrárias 2013; 34(5): 2007-2024. http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007
» http://dx.doi.org/10.5433/1679-0359.2013v34n5p2007 - Choi JY, Engel BA. Real-time watershed delineation system using Web-GIS. Journal of Computing in Civil Engineering 2003; 17(3): 189-196. http://dx.doi.org/10.1061/(ASCE)0887-3801(2003)17:3(189)
» http://dx.doi.org/10.1061/(ASCE)0887-3801(2003)17:3(189) - Environmental Systems Research Institute – ESRI. ArcGIS Professional GIS for the desktop. version 9.3 [software]. Redlands: ESRI; 2008.
- Fairfield J, Leymarie P. Drainage networks from grid digital elevation models. Water Resources Research 1991; 27(5): 709-717. http://dx.doi.org/10.1029/90WR02658
» http://dx.doi.org/10.1029/90WR02658 - Ferrari JL, Silva SF, Santos AR, Garcia RF. Análise morfométrica da sub-bacia hidrográfica do córrego Horizonte, Alegre, ES. Agrária 2013; 8(2): 181-188. http://dx.doi.org/10.5039/agraria.v8i2a1575
» http://dx.doi.org/10.5039/agraria.v8i2a1575 - Garbrecht J, Martz LW. Network and subwatershed parameters extracted from digital elevation models: the bills creek experience. Journal of the American Water Resources Association 1993; 29(6): 909-916. http://dx.doi.org/10.1111/j.1752-1688.1993.tb03251.x
» http://dx.doi.org/10.1111/j.1752-1688.1993.tb03251.x - Instituto Brasileiro de Geografia e Estatística – IBGE. Mapa de solos do Brasil [online]. Rio de Janeiro: IBGE; 2002 [cited 2015 July 17]. Available from: ftp://geoftp.ibge.gov.br/mapas_tematicos/mapas_murais/solos.pdf
- Instituto de Geociências Aplicadas – IGA. Atlas digital de Minas Gerais: geomorfologia [online]. Belo Horizonte: IGA; 2016 [cited 2016 May 20]. Available from: http://www.iga.mg.gov.br/mapserv_iga/atlas/TutorialPDF/7-Geomorfologia.pdf
» http://www.iga.mg.gov.br/mapserv_iga/atlas/TutorialPDF/7-Geomorfologia.pdf - Lindsay JB, Rothwell JJ, Davies H. Mapping outlet points used for watershed delineation onto DEM-derived stream networks. Water Resources Research 2008; 44(8): W08442. http://dx.doi.org/10.1029/2007WR006507
» http://dx.doi.org/10.1029/2007WR006507 - Medeiros LC, Ferreira NC, Ferreira LG. Avaliação de modelos digitais de elevação para delimitação automática de bacias hidrográficas. Revista Brasileira de Cartografia 2009; 61(2): 137-151.
- National Aeronautics and Space Administration – NASA. Shuttle radar topography mission [online]. Washington; 2018 [cited 2018 July 6]. Available from: http://www2.jpl.nasa.gov/srtm/index.html
» http://www2.jpl.nasa.gov/srtm/index.html - O’Callaghan JF, Mark DM. The extraction of drainage networks from digital elevation data. Computer Vision Graphics and Image Processing 1984; 28(3): 323-344. http://dx.doi.org/10.1016/S0734-189X(84)80011-0
» http://dx.doi.org/10.1016/S0734-189X(84)80011-0 - Oliveira PTS, Alves T So, Steffen JL, Rodrigues DBB. Caracterização morfométrica de bacias hidrográficas através de dados SRTM. Revista Brasileira de Engenharia Agrícola e Ambiental 2010; 14(8): 819-825. http://dx.doi.org/10.1590/S1415-43662010000800005
» http://dx.doi.org/10.1590/S1415-43662010000800005 - Pinheiro ES. Comparação entre dados altimétricos Shuttle Radar Topography Mission, cartas topográficas e GPS: Numa área com relevo escarpado. Revista Brasileira de Cartografia 2006; 58(1): 1-9.
- Rabus B, Eineder M, Roth A, Bamler R. The shuttle radar topography mission – a new class of digital elevation models acquired by spaceborne radar. ISPRS Journal of Photogrammetry and Remote Sensing 2003; 57(4): 241-262. http://dx.doi.org/10.1016/S0924-2716(02)00124-7
» http://dx.doi.org/10.1016/S0924-2716(02)00124-7 - Rawat KS, Krishna G, Mishra A, Singh J, Mishra SV. Effect of DEM data resolution on low relief region sub-watershed boundaries delineating using of SWAT model and DEM derived from CARTOSAT-1 (IRS-P5), SRTM and ASTER. Journal of Applied and Natural Science 2014; 6(1): 144-151. http://dx.doi.org/10.31018/jans.v6i1.391
» http://dx.doi.org/10.31018/jans.v6i1.391 - Ribeiro C, Pires J, Nascimento M, Santana R. Análise da exatidão de diferentes métodos de interpolação para geração de modelos digitais de elevação e obtenção de características morfométricas em bacias hidrográficas. Revista Brasileira de Recursos Hídricos 2005; 10(2): 39-47. http://dx.doi.org/10.21168/rbrh.v10n2.p39-47
» http://dx.doi.org/10.21168/rbrh.v10n2.p39-47 - Romano AW, Soares ACP. Geologia da folha Pará de Minas SE.23-Z-C-IV Belo Horizonte: CPRM; 2007.
- Saadi A. A geomorfologia da Serra do Espinhaço em Minas Gerais e de suas margens. Geonomos 1995; 3(1): 41-63.
- Seyler F, Muller F, Cochonneau G, Guimarães L, Guyot JL. Watershed delineation for the Amazon sub-basin system using GTOPO30 DEM and a drainage network extracted from JERS SAR images. Hydrological Processes 2009; 23(22): 3173-3185. http://dx.doi.org/10.1002/hyp.7397
» http://dx.doi.org/10.1002/hyp.7397 - Sodré RVR, Carvalho AO Jr, Machado WP, Oliveira SN, Gomes RAT, Guimarães RF. Classificação de bacias de drenagem do Alto Jequitaí (Minas Gerais) a partir da análise de principais componentes e análise de grupos. Revista Brasileira de Geomorfologia 2007; 8(2): 73-86. http://dx.doi.org/10.20502/rbg.v8i2.95
» http://dx.doi.org/10.20502/rbg.v8i2.95 - Valeriano MM, Abdon MM. Aplicação de dados SRTM a estudos do Pantanal. Revista Brasileira de Cartografia 2007; 59(1): 63-71.
Publication Dates
-
Publication in this collection
30 May 2019 -
Date of issue
2019
History
-
Received
11 June 2016 -
Accepted
10 June 2018